Find Parts That Fit Your Vehicle

Differential Mounts

Differential Bushings can vastly change the feel of your BMW. While you may notice a slight increase in NVH, upgrading your differential bushings will give your rear end a more planted feel that you can't put a price on.

Sort By:

Febi Rear Differential Carrier Bushing - E82, E84, E88, E90, E91, E92...

We Price Match - Give Us A Call or Chat!

T#:382058

Part#: 33176760287

In Stock at Vendor

$ 27.99

This product was last offered at the strikethrough price on
05-07-2026

$ 23.99 USD

Add to Wish List

Qty

$ 23.99 USD

Add to Wish List

Prevent expensive damage and eliminate unwanted drivetrain flex, replace worn carrier bushings.

F9X X3/4M Billet Diff Lock Down Kit

T#:26404860

Part#: VTT-F9X-LDK

Back Ordered

Starting at $ 314.99 USD

Add to Wish List

Starting at $ 314.99 USD

Add to Wish List

VTT noticed a hole in the F9X X3/4M market for a high-quality, lightweight, NVH-friendly, and easy-to-install Diff Lock Down kit to improve diff stability under launching, and hard cornering. So we did something about it and went to work on a very innovative design that 100% positively locks the diff down from movement, while shielding it from adding a ton of NVH, and can be used with the stock diff, and subframe bushings. This design uses existing mounting points on the vehicle, you do NOT have to remove the subframe or the Diff to install. Simply remove 4 differential bolts, drill two holes in the subframe slightly bigger, install two M8 riv-nuts, and install the lockdown, you do not even have to move the exhaust. A typical install can be 30-45 minutes for someone who is experienced working on vehicles, an hour or two if you like taking it slow. Features: Lightweight 1.5 lbs for the entire lockdown plate Uses FOUR connection points on the Diff, and three on the subframe for the ultimate in positive diff location, this will stop all diff movement on launch, saving your guibos, etc 100% Billet construction from 6061-T6 aluminum Anodized in 3 colors for corrosion resistance, a long-lasting finish, and good looks The subframe does NOT have to be removed for installation Uses all 12.9 grade hardware Does not add excessive NVH Positively locks down the diff to eliminate all unwanted movement under launches, acceleration, cornering, etc.

Show More Show Less

Febi Subframe Mount Bushing - E30

We Price Match - Give Us A Call or Chat!

T#:3660

Part#: 33311129144

In Stock

$ 19.99

This product was last offered at the strikethrough price on
07-10-2026

$ 15.99 USD

Add to Wish List

Qty

$ 15.99 USD

Add to Wish List

The E30 rear subframe is held into the chassis by two bolts going through these rubber mounts. A lot of suspension motion, chassis flex, and driveline torque has to go through these two points, which makes them notorious for failure. When they do, the subframe will move around, playing havoc with your suspension's alignment and settings and making a very annoying clunk. These are direct replacement rubber mounts, sold as a pair. This item fits the following BMWs: 1984-1991 E30 BMW 318i 318is 318ic 325e 325es 325i 325ic 325is M3

Show More Show Less

Billet Diff Lock Down Kit

T#:21176906

Part#: VTT-A9X-DLD

In Stock

Sale - Save 7% $ 313.99

This product was last offered at the strikethrough price on
05-04-2026

Starting at $ 291.99 USD

Add to Wish List

Sale - Save 7%

$ 313.99

This product was last offered at the strikethrough price on
05-04-2026

Starting at $ 291.99 USD

Add to Wish List

VTT noticed a hole in the A9X/Z4 market for a high-quality, lightweight, NVH-friendly, and easy-to-install Diff Lock Down kit to improve diff stability under launching, and hard cornering. Vargas went to work on a very innovative design that 100% positively locks the diff down from movement, while shielding it from adding a ton of NVH, and can be used with the stock diff, and subframe bushings. This design uses existing mounting points on the vehicle, you do NOT have to remove the subframe or the Diff to install. Simply remove 4 diff bolts, drill two holes in the subframe slightly bigger, install two M10 riv-nuts, and install the lockdown, you do not even have to move the exhaust. A typical install can be 15-30 minutes for someone who is experienced. You will need a Riv-nut tool to install the Riv-nuts as one is not included. Features: Lightweight 1.5 lbs for the entire lockdown plate Uses FOUR connection points on the Diff, and two on the subframe for the ultimate in positive diff location, this will stop all diff movement on launch, saving your guibos, etc 100% Billet construction from 6061-T6 aluminum Anodized in 4 colors for corrosion resistance, a long-lasting finish, and good looks The subframe does NOT have to be removed for installation Uses all 12.9 grade hardware Does not add excessive NVH Positively locks down the diff to eliminate all unwanted movement under launches, acceleration, cornering, etc.

Show More Show Less