Shock Mount Kits

BMW E9X Front Upper Strut Mount - Priced Each

T#:594663

Part#: 31336775097

In Stock

$ 46.99 USD

Add to Wish List

Qty

$ 46.99 USD

Add to Wish List

The upper strut mount provides a locating point for the top of the front struts. It contains a rubber-isolated bearing that allows the strut shaft to move independently from the rest of the suspension - a critical component for the suspension to be quiet and effective. The rubber also absorbs vibrations and impact harshness, helping to keep unwanted noise and harshness from reaching the steering wheel.
Price is per mount. Left and Right are the same.

This item fits the following BMWs:
2006-2011 E90 BMW 325xi 328xi 328i xDrive 330xi 335xi 335i xDrive - Sedan
2006-2012 E91 BMW 325xi 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328xi 328i xDrive 335xi 335i xDrive - Coupe

Show More Show Less

Rear Shock Mounts (RSM) - Lower + Upper - OEM Rubber - E82, E9X (not ...

T#:11953

Part#: E9X-REAR-MOUNTS

Ships in 3 Business Days

$ 96.91 USD

Add to Wish List

Qty

$ 96.91 USD

Add to Wish List

A 5-piece set of new OEM rear upper and lower shock mounts to complete your shock install or replace broken mounts (RSM). The top mounts on the shocks for the E82 1-series and E90/E91/E92/E93 3-series consist of 4 pieces -
A. rear upper-top shock mounts, 33506771737
B. rear upper-middle shock mounts, 33506767010
C. rear upper-bottom shock mounts, 33506771738
D. rear upper supporting cup, 33526764418 (sits over bumpstop)
In addition, there is a lower shock mount to locate the shock to the suspension (installs on spring arm), 33526768544.

That's a lot of rubber that takes constant deflecting and absorbing of cornering forces and impacts from bumps, potholes, etc. Replacing the RSMs is key to maintaining a quiet and comfortable ride. Price is for all 5 pieces.

This item fits the following BMWs:
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive - Sedan
2006-2011 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2012 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive - Coupe
2007-2012 E93 BMW 328i 335i - Convertible

Show More Show Less

OEM Sachs Rear Shock Mount - E39 525/528/530/540i (w/o EDC)

T#:369231

Part#: 33521091710

In Stock

$ 47.99

This product was last offered at the strikethrough price on
04-30-2026

$ 28.99 USD

Add to Wish List

Qty

$ 28.99 USD

Add to Wish List

While replacing rear shocks it is a good idea to inspect / replace these mounts as the rubber can wear and crack over time. This mounts at the top of the rear shock and is held into the chassis with 3 bolts.

Show More Show Less

1-series Strut/Shock Mount Kit - E82 128i, 135i

T#:11958

Part#: E82MOUNTKIT

Ships in 3 Business Days

Sale - Save 2% $ 167.99

This product was last offered at the strikethrough price on
04-16-2026

$ 165.35 USD

Add to Wish List

Qty

Sale - Save 2%

$ 167.99

This product was last offered at the strikethrough price on
04-16-2026

$ 165.35 USD

Add to Wish List

Replacing your struts and shocks? Don't forget the bushings! The rubber mounts for the shocks will go bad over time, especially if you drive hard or the roads are particularly rough. The shock mounts locate the front struts and rear shocks to the car - providing a quiet and vibration-free buffer between the road and the cabin. Shock mounts and bushings can wear out just like any other rubber part on the car. This leads to more noise and harshness reaching the chassis and may complicate your new suspension install. When installing new shocks, that is the perfect time to also replace the mounts. There is no additional time to install them, no special tools required, and doesn't take any extra time! If you re-use the original mounts you have the risk of them failing before your next shock replacement, doubling your labor costs.

Included in the E82 1-series Mount Kit:

front upper strut mounts (also known as a guide support), 31306775098

A. rear upper-top shock mounts, 33506771737

B. rear upper-middle shock mounts, 33506767010

C. rear upper-bottom shock mounts, 33506771738

D. rear upper supporting cup, 33526764418 (sits over bumpstop)

rear lower shock mount (installs on spring arm), 33526768544
Buy as a package and save $!!

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i - Coupe
2008-2012 E88 BMW 128i 135i - Convertible

Show More Show Less

OEM Rear Shock Mounts (RSM) - Upper - OEM Rubber - E82 1M, E9X M3 (no...

T#:11954

Part#: TMS11954

In Stock

Sale - Save 2% $ 49.12

This product was last offered at the strikethrough price on
05-03-2026

$ 48.01 USD

Add to Wish List

Qty

Sale - Save 2%

$ 49.12

This product was last offered at the strikethrough price on
05-03-2026

$ 48.01 USD

Add to Wish List

A 4-piece set of new OEM rear upper and lower shock mounts to complete your shock install or replace broken mounts (RSM). The top mounts on the shocks for the E82 1M and E90/E92/E93 M3 consist of 4 pieces. These are the mounts to fit a non-EDC suspension.

Rear Shock Mount (RSM) Kit consists of:
A. rear upper-top shock mounts, 33506771737
B. rear upper-middle shock mounts, 33506767010
C. rear upper-bottom shock mounts, 33506771738
D. rear upper supporting cup, 33526764418 (sits over bumpstop)
The lower mount on the 1M/M3 is integrated on the shock absorber.

That's a lot of rubber that takes constant deflecting and absorbing of cornering forces and impacts from bumps, potholes, etc. Replacing the RSMs is key to maintaining a quiet and comfortable ride. Price is for all 4 upper pieces.

This item fits the following BMWs:
2011-2012 E82 BMW 1M
2008-2011 E90 BMW M3 - Sedan
2008-2012 E92 BMW M3 - Coupe
2008-2012 E93 BMW M3 - Convertible

Show More Show Less

3-series Front and Rear Strut/Shock Mount Kit - E9X Xi AWD

T#:340289

Part#: TMS11957

Ships in 3 Business Days

Starting at $ 167.45 USD

Add to Wish List

Starting at $ 167.45 USD

Add to Wish List

New mounts should be installed whenever you are replacing the struts and shocks on your E90 and E92 3-series. The mounts keep the cabin isolated from annoying noises and impacts. Just like any other rubber mount, these will go bad over time, which allows more harshness and vibration to the chassis along with clunking noises. Replace them now to avoid doubling the labor charges down the road. When installing new shocks, that is the perfect time to also replace the mounts. There are no special tools required and don't take any extra time!

Included in the Xi Mount Kit:

front upper strut mounts (also known as a guide support), 31336775097 or 31306785962

A. rear upper-top shock mounts, 33506771737

B. rear upper-middle shock mounts, 33506767010

C. rear upper-bottom shock mounts, 33506771738

D. rear upper supporting cup, 33526764418 (sits over bumpstop)

rear lower shock mount (installs on spring arm), 33526768544
Buy as a package and save $!! Select the kit that fits the production date of your car below.

This item fits the following BMWs:
2006-2011 E90 BMW 325xi 328xi 328i xDrive 330xi 335xi 335i xDrive - Sedan
2006-2011 E91 BMW 325xi 328xi 328i xDrive - Wagon
2007-2012 E92 BMW 328xi 328i xDrive 335xi 335i xDrive - Coupe

Show More Show Less

OEM Sachs Upper Front Strut Mount - E39 540i M5, E52 Z8

T#:348794

Part#: 31331091708

Ships in 1 Business Day

$ 91.64

This product was last offered at the strikethrough price on
08-17-2026

$ 82.93 USD

Add to Wish List

Qty

$ 82.93 USD

Add to Wish List

This is the front shock mount that connects the top of the front shock to the body of the car. Sold Individually.

URO Rear Shock Mount

T#:7276182

Part#: 33526773669

Ships in 1 Business Day

$ 37.99 USD

Add to Wish List

Qty

$ 37.99 USD

Add to Wish List

Common failure component producing an audible clunk over bumps. Recommended to be replaced with shock replacement, or as failure is indicated. Priced each, fits left or right sides. Replace in pairs for best results.

Show More Show Less

Front Strut Mount - Priced Each

T#:584490

Part#: 33506787178

Ships in 1 Business Day

$ 29.99 USD

Add to Wish List

Qty

$ 29.99 USD

Add to Wish List

Shock and Strut Installation Kit - E9X 325xi 328xi 330xi 335xi ...

T#:554760

Part#: E9XXISIKT

Ships in 3 Business Days

$ 382.06 USD

Add to Wish List

Qty

$ 382.06 USD

Add to Wish List

Replacing your struts and shocks? Don't forget the bushings! The rubber mounts for the shocks will go bad over time, especially if you drive hard or the roads are particularly rough. The shock mounts locate the front struts and rear shocks to the car - providing a quiet and vibration-free buffer between the road and the cabin. Shock mounts and bushings can wear out just like any other rubber part on the car. This leads to more noise and harshness reaching the chassis and may complicate your new suspension install. When installing new shocks, that is the perfect time to also replace the mounts. There is no additional time to install them, no special tools required, and doesn't take any extra time! If you re-use the original mounts you have the risk of them failing before your next shock replacement, doubling your labor costs.

This item fits the following BMWs:
2006-2012 E9X BMW All xi models - 325xi 328xi 330xi 335xi

Show More Show Less

Rear Upper Shock Mount Kit

T#:15710806

Part#: 33506771738-KT

In Stock

Sale - Save 2% $ 49.12

This product was last offered at the strikethrough price on
05-03-2026

$ 48.01 USD

Add to Wish List

Qty

Sale - Save 2%

$ 49.12

This product was last offered at the strikethrough price on
05-03-2026

$ 48.01 USD

Add to Wish List

Includes all the necessary mounts to install new shocks on the rear of your E9X BMW. The following parts are included. Rear Upper Shock Mount - Upper Section (x2) Rear Upper Shock Mount - Lower Section (x2) Supporting Cup (x2) Sealing grommet (x2)

Show More Show Less

Self Leveling Delete Kit - E34

T#:11978

Part#: TMS11978

Ships in 7 Business Days

$ 200.88

This product was last offered at the strikethrough price on
07-09-2026

$ 195.12 USD

Add to Wish List

Qty

$ 195.12 USD

Add to Wish List

Some E34 5 series came equipped with self leveling suspension to provide a stable ride height when carrying extra passengers. While it helped to improve ride quality it is not always the best for performance, and the self leveling system parts can be very expensive to replace. Our self leveling delete kit provides all the parts required to convert your E34 sedan to a standard type suspension. Shocks and Springs are sold separately. We recommend Bilstein Shocks and H&R springs for improved performance.

Kit includes:
2 - 33521132270 - Rear Shock Mount / Guide Support
2 - 33531133671 - Spring Pad Lower
2 - 33521136063 - Support
2 - 33531133670 - Spring Pad Upper
4 - 33521129565 - Washer
2 - 33531135624 - Additional Shock Absorber (bump stop)
2 - 31331134314 - Shock Protection Tube
2 - 34326757282 - Intermediate Piece

This item fits the following BMWs:
1989-1995 E34 BMW 525i 530i 535i 540i M5
1991-1995 E34 BMW 525i 530i - Wagon - Factory Euro Non-Leveling Springs Recommended.

Show More Show Less

3-series Strut/Shock (non-EDC) Mount Kit - E90 M3, E92 M3, E93 M3 ...

T#:11950

Part#: E9XM3MOUNTKIT

In Stock

$ 650.52 USD

Add to Wish List

Qty

$ 650.52 USD

Add to Wish List

Any change of your M3 struts and shocks should include new mounts. Installing new bushings and mounts is very easy when changing the shocks - there's no additional time or no special tools required! If you re-use the original mounts you have the risk of them failing before your next shock replacement, doubling your labor costs.

The shock mounts locate the front struts and rear shocks to the car - providing a quiet and vibration-free buffer between the road and the cabin. Shock mounts and bushings can wear out just like any other rubber part on the car. This leads to more noise and harshness reaching the chassis and may complicate your new suspension install.

This package is for cars NOT equipped with the EDC suspension.

Included in the E9X M3 Mount Kit:

front upper strut mounts with bearings (also known as a guide support), 31302283650

A. rear upper-top shock mounts, 33506771737

B. rear upper-middle shock mounts, 33506767010

C. rear upper-bottom shock mounts, 33506771738

D. rear upper supporting cup, 33526764418 (sits over bumpstop)
Buy as a package and save $!!

This item fits the following BMWs without EDC suspension
2008-2012 E90 BMW M3 - Sedan
2008-2012 E92 BMW M3 - Coupe
2008-2012 E93 BMW M3 - Convertible

Show More Show Less

3-series Strut/Shock Mount Kit - Rubber Bushings - E30 318i/325e/325i...

T#:338659

Part#: E30MOUNTKIT

Back Ordered

Sale - Save 3% $ 286.99

This product was last offered at the strikethrough price on
06-13-2026

Starting at $ 278.38 USD

Add to Wish List

Sale - Save 3%

$ 286.99

This product was last offered at the strikethrough price on
06-13-2026

Starting at $ 278.38 USD

Add to Wish List

This package of mounts includes the front and rear mounts that should also be installed when replacing your struts and shocks. Don't overlook your rubber suspension mounts as they wear out just as fast (or faster) as the shocks themselves. Installing these new mounts does not take any additional time, effort, or special tools. These are direct replacements for the mounts already on the car.

E30 Mount Kit includes -

Front upper strut mounts (guide support), standard alignment settings (not offset)

Front and rear self-locking mounting nuts

Rear Lifetime Warranty 'Repair Shop' shock mounts

Rear shock mount gaskets
We offer three varieties of the rear shock mounts - OEM, Repair Shop, and HP alum-rubber. We recommend either the Repair Shop or HP mounts because the stock OEM design has a flaw that can lead to premature failure of the mounts. The Repair Shop and HP mounts use a different design that will last longer and the Repair Shop mounts also have a lifetime warranty!

This item fits the following BMWs:
1984-1991 E30 BMW 318i 318is 318ic 325e 325es 325i 325ic 325is M3

Show More Show Less

3-series Strut/Shock Mount Kit - E36 M3 96-99

T#:348546

Part#: TMS11812DK

Ships in 4 Business Days

Sale - Save 2% $ 439.99

This product was last offered at the strikethrough price on
08-04-2026

Starting at $ 431.10 USD

Add to Wish List

Sale - Save 2%

$ 439.99

This product was last offered at the strikethrough price on
08-04-2026

Starting at $ 431.10 USD

Add to Wish List

This strut and shock mount package covers the front and rear rubber mounts and bushings commonly replaced during a strut and shock install. While you're installing new front struts and rear shocks these are easily installed - there's no additional labor and special tools are not required. Since these pieces are mostly rubber, they dry up and crack over time. Re-using them lead to problems with fitment or noise, and may have safety issues as well. These mounts and pads are the perfect complement to your new shocks to help restore your car's handling and performance.

We sell the basic strut and shock mount package, which includes:

Front strut mounts (also known as guide support)
Front strut reinforcement plates (to prevent cracking and deforming of the front strut towers)
Front strut tower paper washer gaskets
Front and rear self-locking mounting nuts
Rear Lifetime Warranty 'Repair Shop' shock mounts
Rear shock mount reinforcements (to prevent cracking of shock towers)
Rear shock mount gaskets

In addition, you can add the front spring pads, front bump stops, front dust boots, rear bump stops, and rear dust boots if needed. But please note that some shocks and coil overs come with all or some of these pieces already. If in doubt, check with your supplier on what is included.

We offer three varieties of the rear shock mounts - OEM, Repair Shop, and HP alum-rubber. We recommend either the Repair Shop or HP mounts because the stock OEM design has a flaw that can lead to premature failure of the mounts. The Repair Shop and HP mounts use a different design that will last longer and the Repair Shop mounts also have a lifetime warranty!

This item fits the following BMWs:
1996-1999 E36 BMW M3
1996-2002 Z3 BMW 2.5 2.5i 2.8 3.0i M Coupe

Show More Show Less

3-series Rear Suspension Mount Package - Rubber Street Bushings - E46...

T#:11758

Part#: E46REARBUSHINGS

Back Ordered

Sale - Save 13% $ 746.04

This product was last offered at the strikethrough price on
02-26-2026

$ 650.58 USD

Add to Wish List

Qty

Sale - Save 13%

$ 746.04

This product was last offered at the strikethrough price on
02-26-2026

$ 650.58 USD

Add to Wish List

This package is a complete overhaul of the rear suspension bushings in the E46 3-series. If your car is not feeling as crisp, has irregular tire wear, or has inconsistent (and unsafe) handling it's likely the rear bushings. We put together this package as a total overhaul to restore your car back to its original feel. Depending on the symptoms and diagnosis from your mechanic, it may be logical to replace all of the bushings in the rear suspension (there are 19 total). This is especially true if the subframe is being removed to repair or reinforce the rear floor (prone to failure).

Turner Motorsport is a big believer in using rubber bushings for street cars. Urethanes, Delrin, or aluminum are generally good for reducing compliance and limiting deflection - attributes that don't really work well on roads filled with potholes, railroad crossings, cracks, and expansion joints. The rubber bushings maintain the factory ride/handling traits that won the 3-series praise all over the world. Every bushing will need maintenance or replacement at some point and rubber has proven to last the longest and need less maintenance than anything else, even urethane. And unless competitive driving is your goal, the harder materials are only a gimmick.

Individual Item Descriptions:
Trailing Arm Bushings and Limiters (33 32 2 228 153 and TSU9990001) - our OEM rubber replacement trailing arm bushings (RTABs) are a perfect fit and help maintain rear toe alignment. The Limiters prevent premature bushing wear.
Rear Inner Control Arm Bushings (upper 33 32 1 092 247 and lower 33 32 6 770 824) - new stock inner rubber bushings for the upper spring arm and the lower camber arm. These do not wear out very quickly but should be replaced as a 'While you're in there...' job.
Rear Outer Control Arm Bushings (upper and lower) (33 32 6 775 551) - outer ball joints for the upper spring arm and the lower camber arm. These are the standard ball joint design found on the M3 and are a direct replacement upgrade on the other E46 models.
Rear Shock Mounts (JTD909) - Our very best JT Designs rear shock mounts with gaskets and hardware. If your mounts have not been replaced in the last 40,000 miles, now is the perfect time. Skip this option if you recently replaced mounts or already have an upgraded mount.
Rear Shock Mount Reinforcements (TSU9975100) - Even if your shock mounts are new or recent, the sheetmetal of the rear shock tower can still fatigue, leaving you with a very dangerous and expensive fix. These reinforcements are extra-thick, providing crucial strength to one of the weakest points on the car. They work with nearly every shock mount.
Differential mounts (33 17 1 093 175MY and 33 17 6 751 808MY) - Now is a great time to replace the rubber-isolated differential mounts. The diff mounts take the bulk of the twisting and binding as power is transmitted through the differential. We use a Meyle HD rubber bushing for the rear mount as it's stronger than the factory part.
Rear subframe mounts (33 31 6 770 783, 33 31 6 770 784, and 33 31 6 770 781 x 2) - The heart of the rear suspension, the subframe (or carrier) mounts located the entire rear suspension to the car. There are four mounts in total and bolt up into the rear floor. Worn subframe mounts are one of the leading contributors to rear floor-subframe failure. As the mounts flex, so does the sheetmetal of the chassis, which will fatigue the sheetmetal and crack the spot welds. Therefore, replacement of the subframe mounts is critical and a must when doing the subframe reinforcement or repair.

This item fits the following BMWs:
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi

Show More Show Less

OEM Sachs Rear Shock Mount - E36 E46 Z3

T#:369237

Part#: 33521092362

Back Ordered

$ 29.99 USD

Add to Wish List

Qty

$ 29.99 USD

Add to Wish List

This is the rear shock mount that connects the top of the rear shock to the body of the car. Sold Individually.

5-series Strut/Shock Mount Kit - E39 540i/M5 with Performance Shocks/...

T#:182513

Part#: TMS182513

Back Ordered

Sale - Save 6% $ 765.58

This product was last offered at the strikethrough price on
06-26-2026

$ 716.44 USD

Add to Wish List

Qty

Sale - Save 6%

$ 765.58

This product was last offered at the strikethrough price on
06-26-2026

$ 716.44 USD

Add to Wish List

Part of maintaining the precision and crisp handling of your BMW is with refreshing the shock mounts from time to time. The rubber parts that mount the front struts and rear shocks to the chassis suffer from age and mileage just like any other rubber part on the car. Over time they become weak and sloppy and that leads to poor ride characteristics, alignment issues, poor steering feedback and the associated clunks and other noises.

This set of stock mounts replaces the original worn-out shock mounts, bushings, bearings, bump stops, and pads on your existing suspension. We have built this package specifically for use with an aftermarket performance suspension such as our Bilstein/H&R package or other similar performance shocks and springs. This makes a great package when upgrading the non-sport package as the original standard mounts and bushings were not designed for the sport/performance suspension. Installing new mounts with new struts and shocks will ensure proper performance and avoid doing the labor twice if a used mount fails soon after. These are all factory BMW or OEM parts so they fit right and perform just like the factory original parts.

Included in our E39 mount kit is:

front strut bearing dust cap

front strut mount

front upper cupped washer (lower dust cap)

flat washer

front upper spring plate

front upper spring pad

front lower spring pad

rear upper cupped washer

rear shock mount

rear upper spring pad

rear lower cupped washer

rear bump stop

rear lower spring pad note: front bump stops are not included in this package because our Bilstein/H&R suspension includes its own internal bump stops

You save $$ when buying all of these parts as a package!!

Note for 1997-1999 528i, 540i: BMW had a factory recall to replace the front struts and lower spring perches on pre-2000 528i and 540i models. The lower spring perch was redesigned to be stronger and our mount kits cover front struts that have already been replaced under this recall. If yours has not been done we strongly recommend contacting your BMW dealer and having the recall and replacement parts installed. This does not apply to most aftermarket struts, including Bilstein, as their spring perch incorporates the new design.

This item fits the following BMWs:
1997-2003 E39 BMW 540 M5i
with suitable aftermarket sports or performance shocks and springs, H&R, Dinan, Eibach, etc

Show More Show Less

Cup Kit/Coilover Installation Kit

T#:16175687

Part#: 31331091708-KT

Ships in 2 Business Days

Sale - Save 1% $ 586.99

This product was last offered at the strikethrough price on
05-03-2026

$ 578.28 USD

Add to Wish List

Qty

Sale - Save 1%

$ 586.99

This product was last offered at the strikethrough price on
05-03-2026

$ 578.28 USD

Add to Wish List

If you are looking to install a cup kit or a set of coilovers on your BMW, this kit will be a great aid in doing so. It includes everything you will need to do the job, so you can admire your work sooner. See kit contents tab for a list of included components.

Show More Show Less

5-series Strut/Shock Mount Kit - E39 525i/528i/530i with Factory Spor...

T#:182511

Part#: TMS182511

Back Ordered

$ 518.34

This product was last offered at the strikethrough price on
08-07-2026

$ 484.12 USD

Add to Wish List

Qty

$ 484.12 USD

Add to Wish List

Part of maintaining the precision and crisp handling of your BMW is with refreshing the shock mounts from time to time. The rubber parts that mount the front struts and rear shocks to the chassis suffer from age and mileage just like any other rubber part on the car. Over time they become weak and sloppy and that leads to poor ride characteristics, alignment issues, poor steering feedback and the associated clunks and other noises.

This set of stock mounts replaces the original worn-out shock mounts, bushings, bearings, bump stops, and pads on your existing suspension. This package includes all of the original parts used in the E39 factory sport suspension. If you're overhauling your E39 suspension with the factory sport shocks and springs this is the mount package you need (see our other listings if you're using performance shocks such as Bilstein). Installing new mounts with new struts and shocks will ensure proper performance and avoid doing the labor twice if a used mount fails soon after. These are all factory BMW or OEM parts so they fit right and perform just like the factory original parts.

Included in our E39 mount kit is:

front strut bearing dust cap

front strut mount

front upper cupped washer (lower dust cap)

front bump stop

flat washer

front upper spring plate

front upper spring pad

front lower spring pad

rear upper cupped washer

rear shock mount

rear upper spring pad

rear lower cupped washer

rear bump stop

rear lower spring pad You save $$ when buying all of these parts as a package!!

Note for 1997-1999 528i, 540i: BMW had a factory recall to replace the front struts and lower spring perches on pre-2000 528i and 540i models. The lower spring perch was redesigned to be stronger and our mount kits cover front struts that have already been replaced under this recall. If yours has not been done we strongly recommend contacting your BMW dealer and having the recall and replacement parts installed. This does not apply to most aftermarket struts, including Bilstein, as their spring perch incorporates the new design.

This item fits the following BMWs:
1997-2003 E39 BMW 525i 528i 530i
with factory sport suspension

Show More Show Less

3-series Strut/Shock Mount Kit - E36, Z3 (not M models)

T#:340167

Part#: E36MOUNTKIT

Back Ordered

Sale - Save 3% $ 320.99

This product was last offered at the strikethrough price on
05-03-2026

Starting at $ 312.43 USD

Add to Wish List

Sale - Save 3%

$ 320.99

This product was last offered at the strikethrough price on
05-03-2026

Starting at $ 312.43 USD

Add to Wish List

The E36 3 Series Strut/Shock Mount Kit includes two OEM front strut tower mounts with bearings, two front strut reinforcement plates , two front strut tower paper washer gaskets, two rear shock tower reinforcement plates , ten M8 13mm head Nyloc nuts, a pair of rear shock tower mount gaskets and your choice of three different rear shock mounts.

You can choose from the HD OEM Rear Mounts , the " Repair Shop" Lifetime Warranty Mounts , or the High Performance Aluminum & Rubber Mounts . Any of these mounts are suitable for street use, we recommend the Performance Aluminum & Rubber Mounts for coil-over suspensions or for cars that see a lot of track use.

When you replace spring or shocks & struts in your car, these mounts must be removed and reinstalled anyway. Do it at the same time you replace shocks to save yourself the the increased labor time if they go bad soon after shock/strutinstall.

Choose your product options below.

This item fits the following BMWs:
6/1992-1998 E36 BMW 318i 318is 318ti 323is 325i 325is 328i 328is - not for convertibles
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i

Show More Show Less

3-series Strut/Shock Mount Kit - E46 M3

T#:338743

Part#: E46M3MOUNTKIT

Back Ordered

$ 806.99

This product was last offered at the strikethrough price on
08-04-2026

Starting at $ 806.23 USD

Add to Wish List

Starting at $ 806.23 USD

Add to Wish List

One of the secrets of the M3's acclaimed handling is its suspension bushings and mounts. That's why you absolutely cannot overlook replacing the rubber mounts when installing new struts and shocks. Since these pieces are mostly rubber, they dry up and crack over time. Re-using them lead to problems with fitment or noise, and may have safety issues as well. These mounts and pads are the perfect complement to your new shocks to help restore your car's handling and performance.

This mount package contains all of the commonly replaced rubber mounts and pads for the front and rear shocks on a 2001-2006 E46 M3 (incl CSL model). These are the direct replacement pieces - there's no additional labor, time, or effort and special tools are not required.

The basic E46 M3 mount package includes:

Front strut mounts (also known as the guide support)

Front upper spring plate with captive bearing

Front strut reinforcement plates (to prevent cracking and deforming of the front strut towers)

Front and rear self-locking mounting nuts

Rear Lifetime Warranty 'Repair Shop' shock mounts

Rear shock mount reinforcements (to prevent cracking of shock towers)

Rear shock mount gaskets
The spring pads, dust boots, and bump stops can be added from the menu below. Note that front bump stops and dust boots are generally not required if you're using Bilstein struts, Bilstein coil overs, H&R coil overs, or KW coil overs. Those struts come with their own front bump stops and boots and may include rear stops and boots as well.

We offer three varieties of the rear shock mounts - OEM, Repair Shop, and HP alum-rubber. We recommend either the Repair Shop or HP mounts because the stock OEM design has a flaw that can lead to premature failure of the mounts. The Repair Shop and HP mounts use a different design that will last longer and the Repair Shop mounts also have a lifetime warranty!

This item fits the following BMWs:
2001-2006 E46 BMW M3 M3 CSL

Show More Show Less

3-series Strut/Shock Mount Kit - E46 325Xi/330Xi

T#:338752

Part#: E46XIMOUNTKIT

Back Ordered

Starting at $ 284.99 USD

Add to Wish List

Starting at $ 284.99 USD

Add to Wish List

If you're replacing the struts and shocks on your 325Xi or 330Xi you should also pick up this mount package. As these cars have gotten older, their rubber mounts have deteroriated. If your shocks have gone bad then chances are very good that the mounts need replacing too. The rubber bushings are designed to isolate the chassis from bumps, potholes, and poor roads and give a harsh-free ride and precise handling. But they won't last forever. These mounts and pads are the perfect complement to your new shocks to help restore your car's handling and performance.

This mount package contains all of the commonly replaced rubber mounts and pads for the front and rear shocks on a 1999-2006 E46 325Xi and 330Xi AWD. These are easily installed - there's no additional labor, time, or effort and special tools are not required.

The basic E46 Xi mount package includes:

Front strut mounts (also known as the guide support)
Front strut reinforcement plates (to prevent cracking and deforming of the front strut towers)
Front and rear self-locking mounting nuts
Rear Lifetime Warranty 'Repair Shop' shock mounts
Rear shock mount reinforcements (to prevent cracking of shock towers)
Rear shock mount gaskets

The spring pads, dust boots, and bump stops can be added from the menu below. Note that front bump stops and dust boots are generally not required if you're using Bilstein struts, Bilstein coil overs, H&R coil overs, or KW coil overs. Those struts come with their own front bump stops and boots and may include rear stops and boots as well.

This item fits the following BMWs:
1999-2006 E46 BMW 325xi 330xi

Show More Show Less

Cup Kit/Coilover Installation Kit

T#:15644325

Part#: 33306760349-KT

Ships in 3 Business Days

$ 364.60 USD

Add to Wish List

Qty

$ 364.60 USD

Add to Wish List

If you are looking to install a cup kit or a set of coilovers on your BMW, this kit will be a great aid in doing so. It includes everything you will need to do the job. See kit contents tab for a list of included components.

Show More Show Less

URO Rear Upper Shock Mount - Lower Section - BMW E82/88 E9X

T#:639538

Part#: 33506771738

Ships in 1 Business Day

$ 5.99 USD

Add to Wish List

Qty

$ 5.99 USD

Add to Wish List

Replace your shock mount each time you replace your shocks to reduce noise and vibrations from the road and suspension system. Failing shock mounts may also end up leading to knocking and rattling sounds coming from the rear suspension. URO Parts is one of the leading manufacturers of high quality direct replacement aftermarket components, covering a wide range of makes and models. All of their replacement parts are manufactured to ISO 9000 certification standards, so you can expect long lasting performance from URO Parts. As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Show More Show Less

Front Strut Mount - Priced Each

T#:14419823

Part#: 31306850031

In Stock

$ 37.99

This product was last offered at the strikethrough price on
06-25-2026

$ 33.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 37.99

This product was last offered at the strikethrough price on
06-25-2026

$ 33.99 USD

Limited Qty Sale

Add to Wish List

Rear Shock Mount Refresh Kit

T#:55281742

Part#: 3352BBKT

In Stock

$ 28.58 USD

Add to Wish List

Qty

$ 28.58 USD

Add to Wish List

This Rear Shock Mount and Gasket Refresh Kit provides exactly what you need to maintain chassis integrity and prevent distracting cabin noise.

Cup Kit/Coilover Installation Kit - With Spring Pads (3-Bolt M10) ...

T#:15677578

Part#: 07119907135-KT

In Stock

$ 581.75 USD

Add to Wish List

Qty

$ 581.75 USD

Add to Wish List

If you are looking to install a cup kit or a set of coilovers on your BMW, this kit will be a great aid in doing so. It includes everything you will need to do the job, so you can admire your work sooner. See kit contents tab for a list of included components.

Show More Show Less

Coilover Installation/Cup Kit - Front - 5-Bolt Strut Mount

T#:27871824

Part#: 31306881930KT4

Ships in 5 Business Days

$ 495.99

This product was last offered at the strikethrough price on
03-11-2026

$ 358.99 USD

Add to Wish List

Qty

$ 358.99 USD

Add to Wish List

Installing a new set of shocks and struts in your BMW? Turner has your back with this complete "cup kit", which contains all the necessary components for ensuring a lasting installation.

See "kit contents" for a detailed list of all components included with this purchase.

Show More Show Less

3-series Strut/Shock Mount Kit - E36 M3 95

T#:348543

Part#: TMS11810DK

Back Ordered

$ 1,515.99

This product was last offered at the strikethrough price on
04-17-2026

Starting at $ 1,070.99 USD

Add to Wish List

Starting at $ 1,070.99 USD

Add to Wish List

This strut and shock mount package covers the front and rear rubber mounts and bushings commonly replaced during a strut and shock install. While you're installing new front struts and rear shocks these are easily installed - there's no additional labor and special tools are not required. Since these pieces are mostly rubber, they dry up and crack over time. Re-using them lead to problems with fitment or noise, and may have safety issues as well. These mounts and pads are the perfect complement to your new shocks to help restore your car's handling and performance.

We sell the basic strut and shock mount package, which includes:

Front strut mounts (also known as guide support)
Front strut reinforcement plates (to prevent cracking and deforming of the front strut towers)
Front strut tower paper washer gaskets
Front and rear self-locking mounting nuts
Rear Lifetime Warranty 'Repair Shop' shock mounts
Rear shock mount reinforcements (to prevent cracking of shock towers)
Rear shock mount gaskets

In addition, you can add the front spring pads, front bump stops, front dust boots, rear bump stops, and rear dust boots if needed. But please note that some shocks and coil overs come with all or some of these pieces already. If in doubt, check with your supplier on what is included.

We offer three varieties of the rear shock mounts - OEM, Repair Shop, and HP alum-rubber. We recommend either the Repair Shop or HP mounts because the stock OEM design has a flaw that can lead to premature failure of the mounts. The Repair Shop and HP mounts use a different design that will last longer and the Repair Shop mounts also have a lifetime warranty!

This item fits the following BMWs:
1995 E36 BMW M3

Show More Show Less

Rear Strut Mount - Priced Each

T#:35863169

Part#: 33521126680

Back Ordered

$ 48.99 USD

Add to Wish List

Qty

$ 48.99 USD

Add to Wish List

While replacing rear shocks it is a good idea to inspect / replace these mounts as the rubber can wear and crack over time. This mounts at the top of the rear shock and is held into the chassis with 3 bolts.

This item fits the following BMWs:
1982-1988 E28 BMW 524td 528e 533i 535i 535is
1983-1989 E24 BMW 633csi 635csi - not for cars with self-levelling

Show More Show Less

5-series Strut/Shock Mount Kit - E39 540i with Factory Sport Suspensi...

T#:182514

Part#: TMS182514

Back Ordered

Sale - Save 5% $ 873.02

This product was last offered at the strikethrough price on
06-26-2026

$ 833.21 USD

Add to Wish List

Qty

Sale - Save 5%

$ 873.02

This product was last offered at the strikethrough price on
06-26-2026

$ 833.21 USD

Add to Wish List

Part of maintaining the precision and crisp handling of your BMW is with refreshing the shock mounts from time to time. The rubber parts that mount the front struts and rear shocks to the chassis suffer from age and mileage just like any other rubber part on the car. Over time they become weak and sloppy and that leads to poor ride characteristics, alignment issues, poor steering feedback and the associated clunks and other noises.

This set of stock mounts replaces the original worn-out shock mounts, bushings, bearings, bump stops, and pads on your existing suspension. This package includes all of the original parts used in the E39 factory sport suspension. If you're overhauling your E39 suspension with the factory sport shocks and springs this is the mount package you need (see our other listings if you're using performance shocks such as Bilstein). Installing new mounts with new struts and shocks will ensure proper performance and avoid doing the labor twice if a used mount fails soon after. These are all factory BMW or OEM parts so they fit right and perform just like the factory original parts.

Included in our E39 mount kit is:

front strut bearing dust cap

front strut mount

front upper cupped washer (lower dust cap)

front bump stop

flat washer

front upper spring plate

front upper spring pad

front lower spring pad

rear upper cupped washer

rear shock mount

rear upper spring pad

rear lower cupped washer

rear bump stop

rear lower spring pad You save $$ when buying all of these parts as a package!!

Note for 1997-1999 528i, 540i: BMW had a factory recall to replace the front struts and lower spring perches on pre-2000 528i and 540i models. The lower spring perch was redesigned to be stronger and our mount kits cover front struts that have already been replaced under this recall. If yours has not been done we strongly recommend contacting your BMW dealer and having the recall and replacement parts installed. This does not apply to most aftermarket struts, including Bilstein, as their spring perch incorporates the new design.

This item fits the following BMWs:
1997-2003 E39 BMW 540i
with factory sport suspension

Show More Show Less

OEM Sachs Upper Strut Mount - E38 740i/Li 750iL

T#:371830

Part#: 31331090611

Back Ordered

$ 46.99 USD

Add to Wish List

Qty

$ 46.99 USD

Add to Wish List

While replacing front shocks it is a good idea to inspect / replace these mounts as the rubber can wear and crack over time. This mounts at the top of the front shock and is held into the chassis with 3 bolts.

Show More Show Less

5-series Strut/Shock Mount Kit - E39 525i/528i/530i

T#:182510

Part#: TMS182510

Back Ordered

$ 491.44

This product was last offered at the strikethrough price on
08-07-2026

$ 457.22 USD

Add to Wish List

Qty

$ 457.22 USD

Add to Wish List

Part of maintaining the precision and crisp handling of your BMW is with refreshing the shock mounts from time to time. The rubber parts that mount the front struts and rear shocks to the chassis suffer from age and mileage just like any other rubber part on the car. Over time they become weak and sloppy and that leads to poor ride characteristics, alignment issues, poor steering feedback and the associated clunks and other noises.

This set of stock mounts replaces the original worn-out shock mounts, bushings, bearings, bump stops, and pads on your existing suspension. We have built this package specifically for use with an aftermarket performance suspension such as our Bilstein/H&R package or other similar performance shocks and springs. This makes a great package when upgrading the non-sport package as the original standard mounts and bushings were not designed for the sport/performance suspension. Installing new mounts with new struts and shocks will ensure proper performance and avoid doing the labor twice if a used mount fails soon after. These are all factory BMW or OEM parts so they fit right and perform just like the factory original parts.

Included in our E39 mount kit is:

front strut bearing dust cap

front strut mount

front upper cupped washer (lower dust cap)

flat washer

front upper spring plate

front upper spring pad

front lower spring pad

rear upper cupped washer

rear shock mount

rear upper spring pad

rear lower cupped washer

rear bump stop

rear lower spring pad note: front bump stops are not included in this package because our Bilstein/H&R suspension includes its own internal bump stops

You save $$ when buying all of these parts as a package!!

Note for 1997-1999 528i, 540i: BMW had a factory recall to replace the front struts and lower spring perches on pre-2000 528i and 540i models. The lower spring perch was redesigned to be stronger and our mount kits cover front struts that have already been replaced under this recall. If yours has not been done we strongly recommend contacting your BMW dealer and having the recall and replacement parts installed. This does not apply to most aftermarket struts, including Bilstein, as their spring perch incorporates the new design.

This item fits the following BMWs:
1997-2003 E39 BMW 525i 528i 530i
with suitable aftermarket sports or performance shocks and springs, H&R, Dinan, Eibach, etc

Show More Show Less

3-series Strut/Shock Mount Kit - MZ3

T#:340357

Part#: MZ3MOUNTKIT

Back Ordered

Sale - Save 3% $ 474.99

This product was last offered at the strikethrough price on
06-13-2026

Starting at $ 460.74 USD

Add to Wish List

Sale - Save 3%

$ 474.99

This product was last offered at the strikethrough price on
06-13-2026

Starting at $ 460.74 USD

Add to Wish List

This strut and shock mount package covers the front and rear rubber mounts and bushings commonly replaced during a strut and shock install. While you're installing new front struts and rear shocks these are easily installed - there's no additional labor and special tools are not required. Since these pieces are mostly rubber, they dry up and crack over time. Re-using them lead to problems with fitment or noise, and may have safety issues as well. These mounts and pads are the perfect complement to your new shocks to help restore your car's handling and performance.

We sell the basic strut and shock mount package, which includes:

Front strut mounts (also known as guide support)

Front strut reinforcement plates (to prevent cracking and deforming of the front strut towers)

Front and rear self-locking mounting nuts

Rear Lifetime Warranty 'Repair Shop' shock mounts

Rear shock mount reinforcements (to prevent cracking of shock towers)

Rear shock mount gaskets
In addition, you can add the front spring pads, front bump stops, front dust boots, rear bump stops, and rear dust boots if needed. But please note that some shocks and coil overs come with all or some of these pieces already. If in doubt, check with your supplier on what is included.

We offer three varieties of the rear shock mounts - OEM, Repair Shop, and HP alum-rubber. We recommend either the Repair Shop or HP mounts because the stock OEM design has a flaw that can lead to premature failure of the mounts. The Repair Shop and HP mounts use a different design that will last longer and the Repair Shop mounts also have a lifetime warranty!

This item fits the following BMWs:
1998-2002 Z3 BMW M Roadster M Coupe

Show More Show Less

3-series Strut/Shock Mount Kit - E36 Convertibles

T#:340163

Part#: E36ICMOUNTKIT

Back Ordered

Sale - Save 3% $ 357.99

This product was last offered at the strikethrough price on
05-03-2026

Starting at $ 348.31 USD

Add to Wish List

Sale - Save 3%

$ 357.99

This product was last offered at the strikethrough price on
05-03-2026

Starting at $ 348.31 USD

Add to Wish List

The E36 3 Series Strut/Shock Mount Kit includes two OEM front strut tower mounts with bearings, two front strut reinforcement plates , front strut tower paper gaskets, two rear shock tower reinforcement plates , ten M8 13mm head Nyloc nuts, a pair of rear shock tower mount gaskets and your choice of three different rear shock mounts.

You can choose from the HD OEM Rear Mounts , the " Repair Shop" Lifetime Warranty Mounts , or the High Performance Aluminum & Rubber Mounts . Any of these mounts are suitable for street use, we recommend the Performance Aluminum & Rubber Mounts for coil-over suspensions or for cars that see a lot of track use.

When you replace spring or shocks & struts in your car, these mounts must be removed and reinstalled anyway. Do it at the same time you replace shocks to save yourself the the increased labor time if they go bad soon after shock/strutinstall.

Choose your product options below.

This item fits the following BMWs:
1994-1998 E36 BMW 318ic 323ic 325ic 328ic M3 Convertible

Show More Show Less

Front Strut Mount - Priced Each

T#:14419845

Part#: 31306852167

Back Ordered

$ 108.99 USD

Add to Wish List

Qty

$ 108.99 USD

Add to Wish List

3-series Strut/Shock Mount Kit - E46 (not M3, not xi)

T#:338747

Part#: E46MOUNTKIT

Back Ordered

Sale - Save 5% $ 377.99

This product was last offered at the strikethrough price on
06-25-2026

Starting at $ 357.85 USD

Add to Wish List

Sale - Save 5%

$ 377.99

This product was last offered at the strikethrough price on
06-25-2026

Starting at $ 357.85 USD

Add to Wish List

This mount package contains all of the commonly replaced rubber mounts and pads for the front and rear shocks on a 1999-2005 E46 3-series (not for M3 or xi AWD). While you're installing new front struts and rear shocks these are easily installed - there's no additional labor and special tools are not required. Since these pieces are mostly rubber, they dry up and crack over time. Re-using them lead to problems with fitment or noise, and may have safety issues as well. These mounts and pads are the perfect complement to your new shocks to help restore your car's handling and performance.

Pick and choose from mounts below:

Front strut mounts (also known as the guide support)

Front strut reinforcement plates (to prevent cracking and deforming of the front strut towers)

Front and rear self-locking mounting nuts

Rear Lifetime Warranty 'Repair Shop' shock mounts

Rear shock mount reinforcements (to prevent cracking of shock towers)

Rear shock mount gaskets The spring pads, dust boots, and bump stops can be added from the menu below. Note that front bump stops and dust boots are generally not required if you're using Bilstein struts, Bilstein coil overs, H&R coil overs, or KW coil overs. Those struts come with their own front bump stops and boots and may include rear stops and boots as well.

We offer three varieties of the rear shock mounts - OEM, Repair Shop, and HP alum-rubber. We recommend either the Repair Shop or HP mounts because the stock OEM design has a flaw that can lead to premature failure of the mounts. The Repair Shop and HP mounts use a different design that will last longer and the Repair Shop mounts also have a lifetime warranty!

This item fits the following BMWs:
1999-2005 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci

Show More Show Less

5-series Strut/Shock Mount Kit - E39 525i/528i/530i with Performance ...

T#:338707

Part#: TMS182510

Back Ordered

$ 491.99

This product was last offered at the strikethrough price on
08-07-2026

Starting at $ 457.22 USD

Add to Wish List

Starting at $ 457.22 USD

Add to Wish List

Part of maintaining the precision and crisp handling of your BMW is with refreshing the shock mounts from time to time. The rubber parts that mount the front struts and rear shocks to the chassis suffer from age and mileage just like any other rubber part on the car. Over time they become weak and sloppy and that leads to poor ride characteristics, alignment issues, poor steering feedback and the associated clunks and other noises.

This set of stock mounts replaces the original worn-out shock mounts, bushings, bearings, bump stops, and pads on your existing suspension. We have built this package specifically for use with an aftermarket performance suspension such as our Bilstein/H&R package or other similar performance shocks and springs. This makes a great package when upgrading the non-sport package as the original standard mounts and bushings were not designed for the sport/performance suspension. Installing new mounts with new struts and shocks will ensure proper performance and avoid doing the labor twice if a used mount fails soon after. These are all factory BMW or OEM parts so they fit right and perform just like the factory original parts.

Included in our E39 mount kit is:

front strut bearing dust cap

front strut mount

front upper cupped washer (lower dust cap)

flat washer

front upper spring plate

front upper spring pad

front lower spring pad

rear upper cupped washer

rear shock mount

rear upper spring pad

rear lower cupped washer

rear bump stop

rear lower spring pad note: front bump stops are not included in this package because our Bilstein/H&R suspension includes its own internal bump stops

You save $$ when buying all of these parts as a package!!

Note for 1997-1999 528i, 540i: BMW had a factory recall to replace the front struts and lower spring perches on pre-2000 528i and 540i models. The lower spring perch was redesigned to be stronger and our mount kits cover front struts that have already been replaced under this recall. If yours has not been done we strongly recommend contacting your BMW dealer and having the recall and replacement parts installed. This does not apply to most aftermarket struts, including Bilstein, as their spring perch incorporates the new design.

This item fits the following BMWs:
1997-2003 E39 BMW 525i 528i 530i
with suitable aftermarket sports or performance shocks and springs, H&R, Dinan, Eibach, etc

Show More Show Less

Project Cars

SELECT YOUR BMW

Sub-Categories

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results