Control Arm Bushings

For all 2001 to 2005 325xi and 330xi. For convenience, we have assembled this bushing carrier bracket kit, to save you time when changing our control arm bushings. It includes two bushing carriers with pre-installed bushings (one left, one right) and mounting bolts.

 These bushing brackets fit all 2001, 2002, 2003, 2004, and 2005 model BMW 325xi and 330xi.

Swapping in E46 control arms into your E30 or E36 significantly increases negative camber by widening the track width and also gives you more clearance for more steering angle. Condor's CNC machined control arm brackets are made from solid steel and are fitted with a solid hex-shaped bushing. Designed for the street or the track, they hold the control arm steady and eliminate "shimmy" caused by stock bushings. They sharpen steering and improve overall driving feel. Comparable to the NLA Treehouse E36 & E30 Eyeball Arms.

Easiest install of any aftermarket solution
Allow clearance for E30 M50 Conversion exhaust
Street Approved, marginal increase in NVH
Easy Installation, no need for a press
CNC machined steel construction
Solid design without the maintenance of spherical bearings
Heavy-Duty replaceable UHMW insert. Don't be misinformed, UHMW is the best material for these inserts. Delrin is not self-lubricating and will crack and degrade over time.
Powder coated white for corrosion resistance
Improve caster with M3 offset geometry
Keep proper steering geometry under high loads
Made in the U.S.A.
Fitment:
E30 84-91 3 Series
E36 92-98 3 series & Z3

Note that you will need to use E36 outer tie rods and E90 inner tie rods when installing in an E30 or E36

Be sure to measure your control arms to determine if you need 21mm or 23mm. Meyle makes a standard e46 control arm and a Heavy Duty control arm. Most HD arms have a hex that is larger in size (23mm). Lifetime Warranty

Swapping in E46 control arms into your E30 or E36 will significantly increase negative camber by widening the track width and will also give you more clearance for more steering angle. Condor's conversion bushings are machined from UHMW due to its high rigidity and low coefficient of friction allowing for minimal suspension bushing deflection (geometry change). They've designed them offset to re-center the wheel and give your e30/e36 the correct caster. They will include a stainless-steel insert that tightly presses over the hex pattern on the E46 control arms. You do not need to grind down your control arms or make any other modifications to your chassis. Please note that you will need to use E36 outer tie rods and E90 inner tie rods when installing in an E30 or E36.

Fitment:
Fits the following Meyle and Lemforder arms with 21-22MM Hex.

LEMFORDER ZHP - 31122282121 & 31122282122
LEMFORDER - 31126777851 & 31126777852
MEYLE HD - 31126777851 & 31126777852
*Please note that Meyle makes a standard e46 control arm and a Heavy Duty control arm. SOME HD arms have a hex that is larger in size. These HD control arms may need to be shaved 1-2 mm for proper fitment.

For someone looking for superior performance and longevity these sealed monoball bushings are the best upper thrust bearing you can buy for an F22 2-series or F3X 3/4-series. The advantage of a monoball bearing is that it will not deflect under load. All of the rubber bushings move in all sorts of directions and that changes your alignment, especially when used with big brake kits or when driven hard. The condition worsens as the bushing wears out. The Dinan monoball sits in a CNC machined aluminum housing which has zero deflection. The monoball allows complete freedom of movement but only at the desired angles. What you get is superior steering precision, better handling from more consistent alignment, and almost infinite bushing life. And thanks to the inner liner and sealed rubber boots there's none of the extra noise or reduced service life of fully solid race bushings. 

We strongly advise using these with new control arms. BMW recommends that the bushings be replaced only once per set of control arms. So if your thrust arm bushings have been replaced already then we do not recommend re-using the arms. The other reason is that the aluminum arms stretch over time which will make the bushings loose inside the arm. Other manufacturers recommend filling the stretched arms with paste but replacing the control arm is the better solution.

For over 35 years, Dinan has been America's premier tuning company, pioneering advancements in BMW modification while retaining a focus on balanced performance that preserves the original character and driving feel that a BMW offers. When you install a Dinan part on your car, know that it's not only carefully developed and tested, but that Dinan stands behind it with a four year, 50,000-mile warranty. Dinan believes so fully in their “total package” approach that once your car has been fitted with enough of their parts, they celebrate your conversion from stock to Dinan with an exclusive trunk badge, displayed proudly by BMW enthusiasts everywhere.

This item fits the following BMWs:
2014+ F22 F23 BMW 228i M235i
2012+ F30 BMW 320i 328i 335i - Sedan
2012+ F32 BMW 428i 435i - Coupe
2013+ F33 BMW 428i 435i - Convertible
2012+ F34 BMW 328i 335i - Gran Turismo
2012+ F36 BMW 428i 435i - GranCoupe

Experience effortless caster adjustment with KMAC's premium inner thrust arm bushings.

Key Features:

1. Patented Design: Enjoy precise adjustments with a single wrench, even under load directly on the alignment rack.

2. Simplified Adjustment: Say goodbye to inaccurate multi-bolt systems and time-consuming disassembly for readjustments.

3. Extensive Adjustment Range: Benefit from the largest and strongest adjustment range available.

4. Mono Ball/Dual-Axis Bushings

5. Enhance brake and steering response with these high-performance bushings.

6. Superior Design: Our unique design surpasses traditional steel spherical bearings, offering over 2 ½ times the load-bearing and impact area.

Upgrade your vehicle's handling and responsiveness with KMAC's innovative inner thrust arm bushings.