Stock rear lower control arms offer very little adjustment for alignment, especially in lowered vehicles, due to their use of an eccentric bolt. These aftermarket performance control arms from ECS Tuning are designed for maximum adjustability, allowing you to maximize handling and minimize tire wear.

To ensure maximum reliability, ECS Tuning's control arms are constructed from strong, lightweight 6061-T6 aluminum and feature a 303 stainless steel center turnbuckle that offers over 8 degrees of fast and precise camber adjustment. The inner bushing is a stock style serviceable OEM bushing for long life and inexpensive maintenance.

Features:

Durable construction suitable for the daily driver and track car alike
8+ degrees adjustment range for dialing in any suspension and wheel/tire setup
Center located adjuster for maximum clearance during adjustment
OEM-style bushing for long life and inexpensive service
Black anodized 6061-T6 aluminum with 303 stainless steel turnbuckle
Includes new hardware
*With the exception of the stance community, most enthusiasts will need no more than a few degrees of adjustment range. Total adjustment often is dependent on wheel/tire clearances.

The rear lower control arms on E82/E9X models are the weakest link in the rear suspension. The arm is made from folded sheetmetal and it bends and deforms easily. Not only will it deform from potholes and curbs, tow truck drivers love to hook onto them without realizing how weak they are. We have seen other race teams complete the box section to make them stronger. A bent arm will throw off the geometry in the suspension, potentially affecting handling and tire wear. These aluminum arms are both lighter and stronger than the factory sheetmetal arms and is the best solution for chronic bending of the stock arm. These are a direct replacement to your stock arms with no changes needed to your alignment. New high-grade hardware is included.

Note: the stock arm is designed from the factory to be intentionally weak. These arms will bend so that something else in the suspension does not break. Our race cars used the stock sheetmetal arm but we replaced them often. We found that it was better to finish a race with a bent arm than not finish due to a catastrophic failure. The ECS arms are still designed to be the weakest link but are far stronger than the factory arm and will not bend as easily.

This item fits the following BMWs:

2008-2013 E82 E88 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 325xi 328i 328xi 330i 330xi 335i 335xi M3 - Sedan
2007-2011 E91 BMW 325i 325xi 328i 328xi - Touring Wagon
2007-2013 E92 BMW 328i 328xi 335i 335is 335xi M3 - Coupe
2007-2013 E93 BMW 328i 335i 335is M3 - Convertible

Maintaining optimal vehicle alignment is crucial, especially when dealing with challenging road or track conditions. To prevent excess tire wear and ensure precise vehicle handling, turn to the Godspeed Project Rear Toe Arms.

These rear toe arms offer stability at high speeds, thanks to their precise alignment capabilities. Unlike traditional rubber bushings that wear quickly, these arms feature solid spherical bushings for exceptional durability. Their heat-treated ball and hard chrome-plated alloy steel composition guarantee strength and longevity.

Not only do these rear toe arms provide cost-effective performance improvements, but they also offer extended adjustment ranges and versatility. Their solid design enhances road feel, giving you more control and confidence in your BMW's performance.

Please note that realignment is recommended after installation, and these rear toe arms are intended for "Track Use Only" due to the increased road noise and vibration caused by solid bushings.

Lowering a vehicle can often lead to the OEM suspension falling out of factory specifications, resulting in compromised handling and uneven tire wear. Godspeed offers the ideal solution with their range of adjustable arms and links designed to correct camber issues and restore your vehicle's performance.

Constructed from heavy-duty steel alloy, these components are built to withstand the test of time. To further ensure durability and protect against corrosion, Godspeed employs a meticulous three-stage powder coating process. These arms and links are engineered as direct replacements for factory components, making installation straightforward with the right tools. What sets them apart is the inclusion of spherical bearings, which provide a tighter feel and superior durability compared to the rubber bushings commonly found in competitors' offerings.

Key Features:

• Heavy Duty Steel Alloy Construction: Ensures exceptional durability
• Spherical Bearing for Exceptional Durability: Delivers a tighter feel and enhanced longevity
• Three-Stage Powder Coating for Corrosion Protection: Guards against corrosion for long-lasting performance
• Adjustable Length for Camber and Track Width: Provides flexibility to fine-tune your vehicle's setup
• Enhances Handling and Eliminates Uneven Tire Wear: Restore your vehicle's performance and tire longevity
• A Must-Have for Lowered Vehicles: Essential for optimizing suspension geometry after lowering
• Allows Camber Correction for Improved Handling: Offers adjustment up to +/- 3 degrees

Upgrade your vehicle's suspension with Godspeed's Adjustable Arms and Links to experience improved handling and resolve camber issues with ease.

This OEM Lemforder rear guide rod for the E38 7 series and E39 5 series chassis helps to control the toe alignment of the car (the horizontal in/out angle of the tire). There is a rubber bushing on the inside and a ball joint on the outside mounting point. When the bushings on the arm wear out they can contribute to a 'wandering' or 'loose' or unstable feeling in the rear. There may also be a clunking noise associated with bumps. This arm is just one part of the rear suspension, and other parts should be checked to confirm which one is causing the issues. Price is for each - order 2 to replace both on the car.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
1997-12/2001 E39 BMW 525i 528i 530i 540i M5
1995-2001 E38 BMW 740i 740il 750il

ALTA Rear Control Arms are the ultimate upgrade for your MINI, replacing your rear lateral links with a solid and performance-focused design. These control arms enhance traction and handling while giving you precise control over camber and toe settings. The flexibility of ALTA control arms allows for fine-tuning without the hassle of removing and reinstalling the linkage. Simply adjust the lock nuts and twist the center section to achieve your desired settings.

These control arms are the perfect complement to other suspension products like springs, coilovers, or sway bars.

Key Features of ALTA Rear Control Arms:

• CNC machined from 6061 aluminum rod for durability.
• Heavy texture powder coating for corrosion resistance and added style.
• Teflon-lined spherical rod ends for a solid connection and improved articulation.
• Aircraft-quality spherical bearings for smooth and precise movement.
• Injected Nylon around the ball center for quiet operation as the part ages.

For a comprehensive rear end upgrade, consider purchasing two sets of control arms to replace both upper and lower control arms. This minimizes deflection from the OEM rubber bushings and reduces weight. Please note that on models with Xenon-style headlamps, some modifications to the leveling sensor mounting may be necessary. For additional details, consult your ALTA dealer or our Tech Department.

ALTA Rear Control Arms come with high-quality hardware, including corrosion-resistant spacers and Grade 8 adjustment nuts.

Control arms begin to wear over time, leading to sloppy control of your vehicle. Anything from knocking, steering vibration, or even loss of vehicle control could occur. An OEM replacement from Lemförder is the perfect option to restore control and suspension quality.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

MINI F Chassis Godspeed Adjustable Rear Control Arms Spherical Bearings - Set Of 2 - Lower

Enhance your Mini's handling with the MINI F Chassis Godspeed Adjustable Rear Control Arms Spherical Bearings - Set Of 2 - Lower. Specifically designed for Mini F Chassis models, these adjustable rear control arms feature spherical bearings for improved performance and durability. Enjoy greater control and precision during spirited driving with this set of high-quality control arms.

• Specifically designed for Mini F Chassis models
• Features spherical bearings for improved performance
• Adjustable design allows for fine-tuning of suspension settings
• Enhances handling and cornering capabilities
• High-quality construction ensures durability and reliability

Control arms are some of the most crucial components on a BMW suspension. The control arms literally control the wheel and suspension as they go through their range of motions. A faulty or worn control arm or ball joint is a very dangerous and potentially life-threatening problem so make sure they are inspected and replaced at regular intervals. For a street-driven car we advise yearly inspection and a full replacement every 3-4 years. For track-driven cars these should be inspected before every event and replaced every two years.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Genuine BMW Control Arm With Rubber Bushing, Left
This item fits the following BMW Chassis:
E70 X5M,E71 X6M,E70 X5,E71 X6,F15,F16

Control arms begin to wear over time, leading to sloppy control of your vehicle. Anything from knocking, steering vibration, or even loss of vehicle control could occur. An OEM replacement from Lemförder is the perfect option to restore control and suspension quality.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Ball joints begin to pop and rattle after a long period of wear and tear. An OEM Lemforder ball joint is the perfect replacement to ensure complete reliability eliminate any noises from the suspension.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMW Chassis:
E70 X5M,E71 X6M,E70 X5,E71 X6,F15,F16

Updated design!  Now shipping!

When an E9X is lowered beyond the limits of just lowering springs, the rear wheels toe-in excessively. This excessive rear toe leads to premature wear, that many people attribute to an increase in negative camber. It has become a common belief that an extremely low vehicle will wear the tires wrong as a matter of consequence. It has become standard practice to go as low as you can and proceed to replace your tires every five to ten thousand miles. Whats more is that when the vehicle reaches a certain ride height, the factory arms become maxed out and there is no way to compensate and dial in the proper toe. You're left with an improperly aligned vehicle that is in effect worse off than it was with the stock suspension installed.

This is not only uneconomical but improper and unsafe. ECS Tuning is proud to offer a solution for this problem in the form of Rogue Engineering E9X adjustable rear toe arms. These arms allow for greater toe adjustment on vehicles that have been lowered with a coilover suspension. With the toe set properly the tires can contact the road properly this maximizes grip and minimizes wear. 

Features:

100% machined and anodized, 6061-T6 lightweight aluminum arms (and collars).

Stainless hardware and spacers are perfect for the tough Northeast climate!

New!  Easy adjustment with 22mm open ended wrench and 5mm allen key!  It only requires 15 ft. lbs. on the clamp to secure the clamp!

New!  Included lock-out kit, replaces factory eccentric hardware.

Updated 3-piece rod ends features 4130 chromoly steel bodies, heat-treated, alloy steel races, and Teflon liners

Extremely easy installation and adjustment (your alignment shop will LOVE you!)

Control arms begin to wear over time, leading to sloppy control of your vehicle. Anything from knocking, steering vibration, or even loss of vehicle control could occur. An OEM replacement from Lemförder is the perfect option to restore control and suspension quality.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

Fits the following chassis:
E60, E61

Control arms are some of the most crucial components on a BMW suspension. The control arms literally control the wheel and suspension as they go through their range of motions. A faulty or worn control arm or ball joint is a very dangerous and potentially life-threatening problem so make sure they are inspected and replaced at regular intervals. For a street-driven car we advise yearly inspection and a full replacement every 3-4 years. For track-driven cars these should be inspected before every event and replaced every two years.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!