Front Control Arm

Swapping in E46 control arms into your E30 or E36 significantly increases negative camber by widening the track width and also gives you more clearance for more steering angle. Condor's CNC machined control arm brackets are made from solid steel and are fitted with a solid hex-shaped bushing. Designed for the street or the track, they hold the control arm steady and eliminate "shimmy" caused by stock bushings. They sharpen steering and improve overall driving feel. Comparable to the NLA Treehouse E36 & E30 Eyeball Arms.

Easiest install of any aftermarket solution
Allow clearance for E30 M50 Conversion exhaust
Street Approved, marginal increase in NVH
Easy Installation, no need for a press
CNC machined steel construction
Solid design without the maintenance of spherical bearings
Heavy-Duty replaceable UHMW insert. Don't be misinformed, UHMW is the best material for these inserts. Delrin is not self-lubricating and will crack and degrade over time.
Powder coated white for corrosion resistance
Improve caster with M3 offset geometry
Keep proper steering geometry under high loads
Made in the U.S.A.
Fitment:
E30 84-91 3 Series
E36 92-98 3 series & Z3

Note that you will need to use E36 outer tie rods and E90 inner tie rods when installing in an E30 or E36

Be sure to measure your control arms to determine if you need 21mm or 23mm. Meyle makes a standard e46 control arm and a Heavy Duty control arm. Most HD arms have a hex that is larger in size (23mm). Lifetime Warranty

Add negative camber to the front wheels of your BMW to increase the stock handling limitations and reduce the issues with outer tire wear during hard cornering. The increased camber adjustment allows for more responsive turn-ins and can slightly reduce the tire wear on the outer edge of the tire.

Benefits:

• Replaces front upper control arms with ones that increase negative camber up to -0.5 degrees
• Improves grip of front tires
• Evens out tire wear during aggressive cornering

For over 35 years, Dinan has been America's premier tuning company, pioneering advancements in BMW modification while retaining a focus on balanced performance that preserves the original character and driving feel that a BMW offers. When you install a Dinan part on your car, know that it's not only carefully developed and tested, but that Dinan stands behind it with a four year, 50,000-mile warranty. Dinan believes so fully in their “total package” approach that once your car has been fitted with enough of their parts, they celebrate your conversion from stock to Dinan with an exclusive trunk badge, displayed proudly by BMW enthusiasts everywhere. This setup is worth 1 point towards your Dinan badge.

Fits the Following BMW's:

2011+ F13 BMW 640i 640iX 650i 650iX 650iX 4.0 650iX 4.4
2012+ F12 BMW 640i 640iX 650i 650iX 650iX 4.0 650iX 4.4
2011 - 2016 F11 BMW 520i 523i 528i 528iX 530dX 530i 535i 535iX 550I
2010 - 2016 F10 BMW 520i 523i 528i 528iX 530i 535i 535iX 550i 550iX Hybrid 5 M5
2009 - 2016 F07 BMW 528i 535i 535iX 550i 550iX 550iX 4.0 550iX 4.4
2013+ F06 BMW 640i 640i xDrive 650i 650i xDrive ALPINA B6X
2010 - 2015 F04 BMW Active Hybrid 7 Active Hybrid 7L
2010 - 2015 F03 BMW 7 Series Sedan F01/F02 Protection versions 750LiS 760LiS
2011 - 2015 F02 BMW Long Wheelbase 740Ld xDrive 740i 740Li xDrive 750Li 750Li xDrive 760Li Active Hybrid 7
2008 - 2010 F02 BMW Long Wheelbase 740Li 750Li 750Li xDrive 760Li ALPINA B7L ALPINA B7LX
2011 - 2015 F01 BMW 740i 750i 750i xDrive
2008 - 2010 F01 BMW 740i 750i 750i xDrive ALPINA B7 ALPINA B7X

Over the years, the road takes a serious toll on your suspension. Pot holes, speed bumps, and road hazards all contribute to a sloppy, weak suspension. To give a better feel to your driving experience, change components as they wear to improve safety and ride comfort.

One item to replace is the control arm. After years of service, the non-serviceable ball joints and other components can begin to wear out. Because some components cannot be replaced, the only solution is replacement of the entire arm.

If replacing any part of your front or rear suspension, it is best to either do it in pairs (both left and right sides), or examine parts that are prone to failure. This will provide the most service life out of replacement parts and assure they are all performing properly.

Referred to as a wishbone by BMW.

For someone looking for superior performance and longevity these sealed monoball bushings are the best upper thrust bearing you can buy for an F22 2-series or F3X 3/4-series. The advantage of a monoball bearing is that it will not deflect under load. All of the rubber bushings move in all sorts of directions and that changes your alignment, especially when used with big brake kits or when driven hard. The condition worsens as the bushing wears out. The Dinan monoball sits in a CNC machined aluminum housing which has zero deflection. The monoball allows complete freedom of movement but only at the desired angles. What you get is superior steering precision, better handling from more consistent alignment, and almost infinite bushing life. And thanks to the inner liner and sealed rubber boots there's none of the extra noise or reduced service life of fully solid race bushings. 

We strongly advise using these with new control arms. BMW recommends that the bushings be replaced only once per set of control arms. So if your thrust arm bushings have been replaced already then we do not recommend re-using the arms. The other reason is that the aluminum arms stretch over time which will make the bushings loose inside the arm. Other manufacturers recommend filling the stretched arms with paste but replacing the control arm is the better solution.

For over 35 years, Dinan has been America's premier tuning company, pioneering advancements in BMW modification while retaining a focus on balanced performance that preserves the original character and driving feel that a BMW offers. When you install a Dinan part on your car, know that it's not only carefully developed and tested, but that Dinan stands behind it with a four year, 50,000-mile warranty. Dinan believes so fully in their “total package” approach that once your car has been fitted with enough of their parts, they celebrate your conversion from stock to Dinan with an exclusive trunk badge, displayed proudly by BMW enthusiasts everywhere.

This item fits the following BMWs:
2014+ F22 F23 BMW 228i M235i
2012+ F30 BMW 320i 328i 335i - Sedan
2012+ F32 BMW 428i 435i - Coupe
2013+ F33 BMW 428i 435i - Convertible
2012+ F34 BMW 328i 335i - Gran Turismo
2012+ F36 BMW 428i 435i - GranCoupe