BMW Ignition Coils

Enhance your BMW's performance with the upgraded BAV Ignition Coil, designed to boost firepower and optimize engine efficiency. These coils boast modified core windings for a faster, more efficient burn, resulting in increased torque at lower RPMs and heightened horsepower in the upper range. While improvements depend on your engine's condition, these coils ensure noticeable enhancements in performance and potential fuel economy benefits.

Product Benefits:

Improved engine firepower and efficiency
Increased torque at lower RPMs
Enhanced horsepower in higher ranges
Potential improvement in fuel economy
Set of six for complete BMW Cooper replacement

Enhance your BMW's performance with the upgraded BAV Ignition Coil, designed to boost firepower and optimize engine efficiency. These coils boast modified core windings for a faster, more efficient burn, resulting in increased torque at lower RPMs and heightened horsepower in the upper range. While improvements depend on your engine's condition, these coils ensure noticeable enhancements in performance and potential fuel economy benefits.

Product Benefits:

Improved engine firepower and efficiency
Increased torque at lower RPMs
Enhanced horsepower in higher ranges
Potential improvement in fuel economy
Set of eight for complete BMW Cooper replacement

MSD Performance Coil Pack for MINI

Before ordering, check whether you need round or flat pin connectors for your MINI's coil pack. The type of pin is determined by the connectors that link the coil to the wiring harness. To check, slide the red locking tab to the right, press down on the tab, and pull the connector off the coil. Examine the pins to see if they are flat or round. Reattach the connector by pushing it back on until it clicks, then slide the red locking tab back to the locked position.

This high-performance coil pack is a popular upgrade among MINI owners looking to enhance their vehicle's performance over the stock coil. The installation requires removing the factory bolts from the old coil and modifying the MSD factory sleeves by drilling out 1/16" to fit the stock bolts.

Kits Include:

• MSD Coil Pack
• MSD Wire Set - Red
• Inductance: 7mH
• Maximum Voltage: 36,000 Volts
• Primary Resistance: 0.51 OHMs
• Secondary Resistance: 12K OHMs
• Turns Ratio: 77:1

Key Benefits:

• Upgraded performance over stock coil pack
• Enhances ignition efficiency and engine performance
• High voltage output of 36,000 volts for stronger sparks
• Low primary resistance of 0.51 OHMs for efficient energy transfer
• High secondary resistance of 12K OHMs for improved performance
• Durable construction for long-lasting use

If you're noticing misfires, poor fuel economy, reduced engine performance, or ignition-related diagnostic trouble codes (DTCs), a failing ignition coil is likely the cause. Late-model BMWs, such as the E60 M5, E63 M6, and E64 M6, use a coil-on-plug ignition system, where each cylinder has its own coil and spark plug for efficient ignition. When a coil fails, the affected cylinder won't receive a spark and will misfire. Even if the misfire doesn’t trigger a DTC, you’ll still feel the difference in engine performance—rough idling, hesitation during acceleration, or a strong fuel smell. To avoid these issues, we recommend replacing your ignition coils every 40,000-60,000 miles.

The S85 engine uses a specialized ignition system called Ionic Current Control, which differs from traditional knock sensors. BMW engineers developed this system to more accurately detect pre-ignition and misfires in the high-revving, ten-cylinder S85. Instead of relying on conventional knock sensors, the system uses each spark plug to measure current after the power stroke, transmitting that data to the Ionic Current Control Unit (ICC). This allows for precise monitoring of combustion events. To support this, the S85’s ignition coils are specially designed with a modified “pencil” shape and lack a Zener diode in the secondary winding, allowing for accurate current measurements without triggering fault codes in the engine control unit (DME). These ignition coils are manufactured to the exact specifications of the OE Ionic Current Control-compatible ignition coil, and will not trigger ignition-related fault codes in the DME.

Bavarian Autosport ignition coils are engineered for reliability, delivering a consistent, long-lasting spark. These high-quality OE replacement coils are specifically designed for your S85-powered E60 M5, E63 M6, or E64 M6. Constructed with durable, heat-resistant plastic and featuring premium rubber spark plug boots, each boot is pre-lubricated with dielectric grease to ensure smooth installation and prevent corrosion.

Whether you're fixing misfires, replacing a faulty coil, or performing preventative maintenance on your S85 ignition system, trust Bavarian Autosport ignition coils for a dependable, lasting repair.

FEATURES:

Durable, heat-resistant plastic: Built to withstand extreme temperatures and harsh driving conditions for long-lasting durability. Pre-lubricated, high-quality rubber boots: Prevent moisture and corrosion while ensuring smooth, easy installation. OE-quality construction: Meets or exceeds original equipment standards for perfect fit, reliable performance, and effortless installation.