Maintaining optimal vehicle alignment is crucial, especially when dealing with challenging road or track conditions. To prevent excess tire wear and ensure precise vehicle handling, turn to the Godspeed Project Rear Toe Arms.

These rear toe arms offer stability at high speeds, thanks to their precise alignment capabilities. Unlike traditional rubber bushings that wear quickly, these arms feature solid spherical bushings for exceptional durability. Their heat-treated ball and hard chrome-plated alloy steel composition guarantee strength and longevity.

Not only do these rear toe arms provide cost-effective performance improvements, but they also offer extended adjustment ranges and versatility. Their solid design enhances road feel, giving you more control and confidence in your BMW's performance.

Please note that realignment is recommended after installation, and these rear toe arms are intended for "Track Use Only" due to the increased road noise and vibration caused by solid bushings.

Swapping in E46 control arms into your E30 or E36 significantly increases negative camber by widening the track width and also gives you more clearance for more steering angle. Condor's CNC machined control arm brackets are made from solid steel and are fitted with a solid hex-shaped bushing. Designed for the street or the track, they hold the control arm steady and eliminate "shimmy" caused by stock bushings. They sharpen steering and improve overall driving feel. Comparable to the NLA Treehouse E36 & E30 Eyeball Arms.

Easiest install of any aftermarket solution
Allow clearance for E30 M50 Conversion exhaust
Street Approved, marginal increase in NVH
Easy Installation, no need for a press
CNC machined steel construction
Solid design without the maintenance of spherical bearings
Heavy-Duty replaceable UHMW insert. Don't be misinformed, UHMW is the best material for these inserts. Delrin is not self-lubricating and will crack and degrade over time.
Powder coated white for corrosion resistance
Improve caster with M3 offset geometry
Keep proper steering geometry under high loads
Made in the U.S.A.
Fitment:
E30 84-91 3 Series
E36 92-98 3 series & Z3

Note that you will need to use E36 outer tie rods and E90 inner tie rods when installing in an E30 or E36

Be sure to measure your control arms to determine if you need 21mm or 23mm. Meyle makes a standard e46 control arm and a Heavy Duty control arm. Most HD arms have a hex that is larger in size (23mm). Lifetime Warranty

ALTA Rear Control Arms are the ultimate upgrade for your MINI, replacing your rear lateral links with a solid and performance-focused design. These control arms enhance traction and handling while giving you precise control over camber and toe settings. The flexibility of ALTA control arms allows for fine-tuning without the hassle of removing and reinstalling the linkage. Simply adjust the lock nuts and twist the center section to achieve your desired settings.

These control arms are the perfect complement to other suspension products like springs, coilovers, or sway bars.

Key Features of ALTA Rear Control Arms:

• CNC machined from 6061 aluminum rod for durability.
• Heavy texture powder coating for corrosion resistance and added style.
• Teflon-lined spherical rod ends for a solid connection and improved articulation.
• Aircraft-quality spherical bearings for smooth and precise movement.
• Injected Nylon around the ball center for quiet operation as the part ages.

For a comprehensive rear end upgrade, consider purchasing two sets of control arms to replace both upper and lower control arms. This minimizes deflection from the OEM rubber bushings and reduces weight. Please note that on models with Xenon-style headlamps, some modifications to the leveling sensor mounting may be necessary. For additional details, consult your ALTA dealer or our Tech Department.

ALTA Rear Control Arms come with high-quality hardware, including corrosion-resistant spacers and Grade 8 adjustment nuts.

When an E9X is lowered beyond the limits of just lowering springs, the rear wheels toe-in excessively. This excessive rear toe leads to premature wear, that many people attribute to an increase in negative camber. It has become a common belief that an extremely low vehicle will wear the tires wrong as a matter of consequence. It has become standard practice to go as low as you can and proceed to replace your tires every five to ten thousand miles. Whats more is that when the vehicle reaches a certain ride height, the factory arms become maxed out and there is no way to compensate and dial in the proper toe. You're left with an improperly aligned vehicle that is in effect worse off than it was with the stock suspension installed.

This is not only uneconomical but improper and unsafe. ECS Tuning is proud to offer a solution for this problem in the form of Rogue Engineering E9X adjustable rear toe arms. These arms allow for greater toe adjustment on vehicles that have been lowered with a coilover suspension. With the toe set properly the tires can contact the road properly this maximizes grip and minimizes wear. 

Features:

• 100% machined and anodized, 6061-T6 lightweight aluminum arms
• High-strength, 3-piece, rod end (with carbon fiber reinforced, PTFE race) offers longer life for street compared to standard rod ends
• SEALS-IT Rod end seals keep dirt, water, and other contaminants out
• Rod ends feature grease fittings, to allow for rod end serviceability.
• Lighter than stock!  (Stock is 875g, RE arms are 640g)
• Extremely easy installation and adjustment (your alignment shop will LOVE you!)

Updated design!  Now shipping!

When an E9X is lowered beyond the limits of just lowering springs, the rear wheels toe-in excessively. This excessive rear toe leads to premature wear, that many people attribute to an increase in negative camber. It has become a common belief that an extremely low vehicle will wear the tires wrong as a matter of consequence. It has become standard practice to go as low as you can and proceed to replace your tires every five to ten thousand miles. Whats more is that when the vehicle reaches a certain ride height, the factory arms become maxed out and there is no way to compensate and dial in the proper toe. You're left with an improperly aligned vehicle that is in effect worse off than it was with the stock suspension installed.

This is not only uneconomical but improper and unsafe. ECS Tuning is proud to offer a solution for this problem in the form of Rogue Engineering E9X adjustable rear toe arms. These arms allow for greater toe adjustment on vehicles that have been lowered with a coilover suspension. With the toe set properly the tires can contact the road properly this maximizes grip and minimizes wear. 

Features:

100% machined and anodized, 6061-T6 lightweight aluminum arms (and collars).

Stainless hardware and spacers are perfect for the tough Northeast climate!

New!  Easy adjustment with 22mm open ended wrench and 5mm allen key!  It only requires 15 ft. lbs. on the clamp to secure the clamp!

New!  Included lock-out kit, replaces factory eccentric hardware.

Updated 3-piece rod ends features 4130 chromoly steel bodies, heat-treated, alloy steel races, and Teflon liners

Extremely easy installation and adjustment (your alignment shop will LOVE you!)