BMW 3 Series G20 (2019+)

• 70MM, 80MM, OR 90MM OVERALL LENGTH
• OUR HIGHEST-GRADE PREMIUM WHEEL STUD
• DRY LUBE WITH BLACK M-PHOSPHATE COATING
• STUD FOR RACE/TRACK USE
• CORRECT SHOULDER SIZE FOR A WIDE RANGE OF HUBS/BRAKE ROTORS
• USE WITH 14x1.5 NUT
  
• For the very best in a race-grade wheel stud, stop looking! These are the wheel studs that our race teams insist on (after years of trying every stud design on the market). MSI Racing specializes in hardware for motorsport use (NASCAR and IMSA) and other advanced industries. We tried them on our Grand-Am/IMSA racecars and were very impressed by the performance and durability of their designs. Race wins and championships can come down to the seconds of a pitstop. We could run any wheel stud in the world and we use these. After testing them over the course of a few endurance seasons we decided to offer them to all of our customers as well.
  
  These studs are available in three overall lengths - 70.5mm, 80.5mm, and 90.5mm. All sizes are made with aircraft quality alloy steel and have roll formed threads for greater strength than cut threads. We use a dry film lubricant HM-30 coating containing Teflon & Moly over a manganese phosphate finish. Manganese is preferred over the more common zinc because it's better at reducing friction and wear to prevent thread galling. With the dry lube applied over the phosphate this is the best corrosion resistance we have seen in any wheel stud! Salt tests have shown this stud is superior to others in corrosion resistance. The dry lube helps the nut engage and glide over the threads for faster engagement without cross threading or binding. Other features of our MSI studs include a large bullet nose nut-starter and a properly sized shank to work with a wider range of BMW wheel, nut, and brake rotor combinations. We intentionally avoid the extra large shoulders you see on other studs because they can interfere with some brake rotor hats. The extra large shoulder can be too large to allow the rotor to pass through and drilling out the holes is required (not cool!) Our studs have the sufficient shank for the brake rotor without interfering.
  
  We configured these studs to have a 14x1.25 thread to go into the wheel hub. But the exposed stud has 14x1.5 threads. We did this because threading a nut is faster on 1.5 threads than a finer 1.25 thread pitch, which saved us time during pitstops. There are also more wheel nut options in 14x1.5. When you order our 14x1.25 studs make sure you also order the 14x1.5 nuts.
   

  FREE red threadlocker with purchase of a full set of wheel studs (16 or more)MSI Dry Lube Bullet Nose Wheel Stud Features:
  

• Dry film lubricant HM-30 coating containing Teflon & Moly over a manganese phosphate finish
• Innovative nut-starter and bullet shape radius that all but eliminates cross-threading
• Properly sized shank to work with a wide range of brake rotor, wheel, and nut combinations
• Heat-treated aircraft quality alloy steel
• Developed from over 20 years of top level NASCAR use
  
• These studs are installed using the traditional 'double-nut' method (one regular nut and one jam nut) with thread locking compound (Red Turbo-Lock or similar).
  
  Sold per stud.
  Wheel nuts sold separately.

If your engine has higher mileage, don't neglect rod bearing replacement! These bearings are sandwiched between the connecting rod and crankshaft journal and are prone to failure due to overheating, lack of lubrication, or general wear. Replace your rod bearings and prevent a spun bearing.

Starting with ACL’s high-performance bearing shells, our Race Series bearings are built to withstand extreme RPMs and stress. Utilizing a "Duraglide" tri-metal construction and a high-strength overlay plate, these bearings offer superior oiling and heat resistance for high-RPM operation.

Our WPC-treated bearings take ACL’s already impressive design and enhance it even further. The WPC treatment process strengthens and smooths the bearing surface by firing high-speed, ultra-fine particles at the bearing shells, reducing friction and improving durability. This advanced surface treatment ensures smoother operation and improved heat dissipation, which are critical for any high-performance engine.

Kit includes:

Turner Motorsport WPC-Treated Race Series Rod Bearing Shells (8) Genuine BMW Connecting Rod Bolts (8) Assembly Lube (4 oz.)

Are you experiencing unsettling creaks and wandering on the road, especially at highway speeds? Your vehicle's front control arms might be the culprit, losing their stability after just 50,000 miles. The solution is our comprehensive refresh kit, designed to upgrade and rejuvenate your front suspension.

This kit includes top-of-the-line components:

Turner Motorsport Adjustable Front Lower Control Arms: Crafted from lightweight Aluminum, Titanium, Chromoly, and Stainless Steel, these arms boast correct ball joint angles for full articulation. The clamp design facilitates easy alignment adjustments, while low friction 3-piece Teflon lined FK spherical bushings and Heim joints ensure smooth operation. Stainless steel roll center spacers of various sizes allow for precise tuning. Turner Motorsport Monoball Front Thrust Arms: Featuring OEM sealed, greased ball joints housed in 6061-T6 anodized aluminum for superior corrosion resistance, these thrust arms guarantee exceptional durability even under harsh conditions. CNC machined 304ss bearing inserts provide a precise fit, ensuring immediate, precise steering feedback with minimal maintenance requirements. Hardware: Our kit includes self-locking nuts, combination nuts, hex-bolts, and cage nuts, ensuring a complete and hassle-free installation. Restore functionality, comfort, and performance to your front suspension with the TMS upgraded refresh kit. Say goodbye to creaks, groans, and unstable handling, and enjoy a smooth and controlled ride on every road.