BMW Intake Parts for BMW 3 Series G20 (2019+)

BMS Elite Charge Pipe w/o BOV - B58 Gen 2

For vehicles equipped with Gen2 B58TU engines only

T#:21209810

Part#: BMS-B58G2CP

In Stock

$ 299.00 USD

Add to Wish List

Qty

$ 299.00 USD

Add to Wish List

Replace the failure prone plastic charge pipe that came on your car before it leaves you stranded. The BMS Elite B58TU charge pipe upgrade is constructed from high-gauge aluminum and features a CNC throttle body and turbo flange for a snug, OEM-style fit. It features a glossy black powder coat to coordinate with the engine bay and includes three 1/8" NPT bungs ideal for an external boost gauge or methanol nozzles. With a double o-ring seal design on the chargepipe flange that attaches to the turbo, this chargepipe is designed to withstand up to 40+psi of high boost. Also includes a heavy-duty replacement coupler, o-rings, clamps, and all required installation hardware. What's Included: (1) Upper charge pipe (1) Lower charge pipe (1) 3R2.5 silicone coupler (1) 2.5" Tbolt clamp (1) 3" Tbolt clamp (3) 1/8NPT plugs (1) M6x1x16mm bolt (2) M6x1x20mm bolts (2) Small O rings (1) Large O ring

Show More Show Less

BMS G20 B58 Billet Intake

T#:597207

Part#: G20-B58-BIT

In Stock

$ 199.00 USD

Add to Wish List

Qty

$ 199.00 USD

Add to Wish List

In BMW's with the B58 engine, the intake system is partially limited. The bottom portion is lightweight and great for feeding cold air to the intake, but the top portion is excessively restrictive. Working with some of the original equipment, this intake continues to utilize the bottom portion of OE ducting and heat shielding, but replaces the top with a new high flow inverted performance cone filter. Extensive testing showed up to a 10+ HP gain to the wheels and allows for quicker turbo spool speed. Plus, this design gives you a great sound improvement, letting you hear both the intake and the turbo spooling!

Show More Show Less

BMS Elite Charge Pipe W/ Turbosmart Raceport BOV- B58 Gen 2 ...

For vehicles equipped with Gen2 B58TU engines only

T#:21209817

Part#: BMS-B58G2CPV

In Stock

$ 629.00 USD

Add to Wish List

Qty

$ 629.00 USD

Add to Wish List

BMS Elite Charge Pipe - B58 Gen 2

T#:21209828

Part#: B58G2CP

In Stock

Starting at $ 299.00 USD

Add to Wish List

Starting at $ 299.00 USD

Add to Wish List

Replace the failure prone plastic charge pipe that came on your car before it leaves you stranded! The BMS Elite B58TU charge pipe upgrade is constructed from high-gauge aluminum and features a CNC throttle body and turbo flange for a snug, OEM-style fit. It features a glossy black powder coat to coordinate with the engine bay and includes three 1/8" NPT bungs ideal for an external boost gauge or methanol nozzles. With a double o-ring seal design on the chargepipe flange that attaches to the turbo, this chargepipe is designed to withstand up to 40+psi of high boost. Also includes a heavy-duty replacement coupler, o-rings, clamps, and all required installation hardware. Now available with or without a Turbosmart Raceport BOV! The blow-off valve version releases excess pressure in the charge pipes when letting off the gas. In addition to intoxicating sound, it reduces compressor surge and improves overall reliability at higher boost levels. Compatible with factory tuning, JB4, and flash tuning. What's Included with the NON-BOV kit ES4715295: (see below for BOV kit) (1) Upper charge pipe (1) Lower charge pipe (1) 3R2.5 silicone coupler (1) 2.5" Tbolt clamp (1) 3" Tbolt clamp (3) 1/8NPT plugs (1) M6x1x16mm bolt (2) M6x1x20mm bolts (2) Small O rings (1) Large O ring What's Included with the BOV kit ES4715315: (1) Turbosmart Blow-Off Valve (1) Lower charge pipe (1) Upper charge pipe with BOV flange (1) 3R2.5 silicone coupler (1) 2.5" Tbolt clamp (1) 3" Tbolt clamp (5) 1/8NPT plugs (1) M6x1x16mm bolt (2) M6x1x20mm bolts (2) Small O rings (1) Large O ring (1) BOV adapter + E clip (2) 90* 1/8NPT to 1/4" push lock fittings (1) 30" 1/4" tubing

Show More Show Less

BMW G20 B58 3.0L BMS Competition Cold Air Intake - Blue

T#:12413847

Part#: B58CLOSEDBLUE

Ships in 2 Business Days

$ 479.00 USD

Add to Wish List

Qty

$ 479.00 USD

Add to Wish List

BMW G20 B58 3.0L BMS Competition Cold Air Intake - Blue is engineered to enhance the performance and sound of your 2019+ BMW M340i, 2022+ M440i, and 2022+ M240i, including xDrive models. This high-performance intake system has been meticulously developed over a year of rigorous street and track testing to deliver superior results.

Enhanced Performance: Features a proprietary renewable inverted cone performance filter that outflows the stock paper filter, ensuring increased airflow and improved engine performance.
OEM+ Design: Maintains a clean OEM+ look while delivering the thrilling sound and performance of an open intake system.
Superior Fitment: Provides excellent fitment with OEM cold air inlet and a large inlet hole on the cold side of the airbox for optimized air intake and sound enhancement.
Effective Heat Shielding: Utilizes the factory heat shield to keep intake temperatures low, ensuring performance consistency.
Smooth Airflow: Replaces the factory rubber accordion hose and resonator with a smooth pipe to reduce air turbulence and improve airflow to the turbo.
Easy Maintenance: Includes a clear window for quick filter inspection and renewable filters that last the life of the vehicle, with built-in velocity stacks for enhanced air intake.

This intake system is designed to extract more performance and sound from your BMW B58 engine while maintaining excellent build quality and fitment.

Show More Show Less

BMS Silicone Intake Pipe Hose Upgrade - G Chassis B58

For Factory Intakes

T#:5108973

Part#: B58GINLET

Ships in 2 Business Days

$ 69.00 USD

Add to Wish List

Qty

$ 69.00 USD

Add to Wish List

Smooths the airflow from the intake to the factory turbo inlet by removing the upper factory sound resonator and the lower accordion section of the air inlet pipe.

Autotecknic Dry Carbon Fiber Cooling Shroud - G20 330I/xDrive ...

T#:5189200

Part#: ATK-BM-0004-G20

Ships on Jul 18, 2025

$ 295.00 USD

Add to Wish List

Qty

$ 295.00 USD

Add to Wish List

AutoTecknic was established in 2000 and has since become one of the largest manufacturers and distributors of carbon fiber parts and accessories for a wide variety of manufacturers. AutoTecknic's Dry Carbon Cooling Plate provides the G20 330I/xDrive with better air induction while providing the intake and engine with cooler air during high-speed driving. It also gives your engine bay a fresh appearance. Dry carbon fiber's name also comes from its manufacturing process. Dry carbon fiber is formed by using a "pre-preg" or impregnated piece of carbon materials. This piece of carbon is first placed into a mold, and then into a sealed vacuum (autoclave) to properly cure. This particular method creates the least amount of waste and forms a lighter version of carbon than the “wet” method. The autoclave vacuuming process of making dry carbon means that there are fewer pinholes and virtually no air pockets that form in the carbon. Dry carbon is the highest quality version of carbon fiber products that are produced.

Show More Show Less

Burger Motorsports Competition Cold Air Intake B48 BMW 230i 330i 430i...

T#:37689739

Part#: BMSB48INTKB

In Stock

$ 479.00 USD

Add to Wish List

Qty

$ 479.00 USD

Add to Wish List

Features & Benefits Adds 12+ horsepower 50% more air than stock Dramatic sound improvement Improves throttle response Retains OEM cold air ducting Looks great under the hood Renewable inverted cone air filter B46/B48 Vehicle Fitment BMW 2 Series - 2022+ G42 G43 B46/B48 BMW 220i 230i 2.0L including Gran Coupe and xDrive BMW 3 Series - 2019+ G20 G21 G28 B46/B48 BMW 330i 2.0L including Gran Coupe and xDrive - 2019+ G20 G21 B46/B48 BMW 330e 2.0L including xDrive - 2019+ G20 G21 B46/B48 BMW 320i 2.0L including xDrive BMW 4 Series - 2021+ G22 G23 G26 B46/B48 BMW 420i 430i 2.0L including Gran Coupe and xDrive What's included? (1) Airbox lid with clear window (5) Stainless Steel button head M6 x 1mm thread, 10mm long hex drive airbox lid screws (2) Stainless steel M4 x 0.7mm Thread, 8mm Long MAF sensor screws (1) High flow airbox bottom (1) Inverted cone BMS renewable performance filter (red or blue) (1) 3.5" High flow intake tube (1) 3.5" silicone coupler (2) 4" heavy-duty 90-110 hose clamps (1) 11.75" piece of rubber weather stripping

Show More Show Less

BMS Competition Cold Air Intake - Red - B58 G Chassis

T#:12413846

Part#: B58CLOSEDRED

Ships in 2 Business Days

$ 479.00 USD

Add to Wish List

Qty

$ 479.00 USD

Add to Wish List

Red Filter - The Burger Motorsports renewable inverted cone filters not only outflow your stock paper filter and last the life of your vehicle they also include built-in velocity stacks. Velocity stacks allow even more air to be smoothly sucked into your intake system.

Show More Show Less

Burger Motorsports Competition Cold Air Intake B58 BMW M240i M340i M4...

T#:37689720

Part#: BMSB58INTKRED

Ships on Jul 15, 2025

$ 479.00 USD

Add to Wish List

Qty

$ 479.00 USD

Add to Wish List

Features & Benefits • Adds up to 18+ horsepower • 50% more air than stock • Dramatic sound improvement • Improves throttle response • Retains OEM heat shield for low IATs • Retains OEM cold air ducting • Looks great under the hood • Renewable inverted cone air filter Gen 2 & 3 B58 Vehicle Fitment BMW 2 Series • 2022+ G42 Gen 2 B58 BMW M240i and M240i xDrive BMW 3 Series • 2020-2024 G20 G21 Gen 2 B58 BMW M340i and M340i xDrive • 2025+ G20 G21 Gen 3 B58 BMW M340i and M340i xDrive BMW 4 Series • 2021-2024 G22 G23 G26 Gen 2 B58 BMW M440i and M440i xDrive including Gran Coupe • 2025+ G22 G23 G26 Gen 3 B58 BMW M440i and M440i xDrive including Gran Coupe What's included? (Gen 2 B58) • (1) Airbox lid with clear window • (5) Stainless Steel button head M6 x 1mm thread, 10mm long hex drive airbox lid screws • (4) Stainless Steel button head M6 x 1mm thread, 10mm long hex drive heat shield screws • (2) Stainless steel M4 x 0.7mm Thread, 8mm Long MAF sensor screws • (1) High flow airbox bottom • (1) 1123 Inverted cone BMS renewable performance filter (red or blue) • (1) High flow intake tube • (1) 4" silicone coupler • (2) 4" heavy-duty 90-110 hose clamps • (1) 11.75" piece of rubber weather stripping

Show More Show Less

Burger Motorsports Competition Cold Air Intake B58 BMW M240i M340i M4...

T#:37689735

Part#: BMSB58INTKBLUE

Ships on Jul 15, 2025

$ 479.00 USD

Add to Wish List

Qty

$ 479.00 USD

Add to Wish List

Features & Benefits Adds up to 18+ horsepower 50% more air than stock Dramatic sound improvement Improves throttle response Retains OEM heat shield for low IATs Retains OEM cold air ducting Looks great under the hood Renewable inverted cone air filter Gen 2 & 3 B58 Vehicle Fitment BMW 2 Series - 2022+ G42 Gen 2 B58 BMW M240i and M240i xDrive BMW 3 Series - 2020-2024 G20 G21 Gen 2 B58 BMW M340i and M340i xDrive - 2025+ G20 G21 Gen 3 B58 BMW M340i and M340i xDrive BMW 4 Series - 2021-2024 G22 G23 G26 Gen 2 B58 BMW M440i and M440i xDrive including Gran Coupe - 2025+ G22 G23 G26 Gen 3 B58 BMW M440i and M440i xDrive including Gran Coupe What's included? (Gen 2 B58) (1) Airbox lid with clear window (5) Stainless Steel button head M6 x 1mm thread, 10mm long hex drive airbox lid screws (4) Stainless Steel button head M6 x 1mm thread, 10mm long hex drive heat shield screws (2) Stainless steel M4 x 0.7mm Thread, 8mm Long MAF sensor screws (1) High flow airbox bottom (1) 1123 Inverted cone BMS renewable performance filter (red or blue) (1) High flow intake tube (1) 4" silicone coupler (2) 4" heavy-duty 90-110 hose clamps (1) 11.75" piece of rubber weather stripping

Show More Show Less

BMS Heat Exchanger Upgrade - G-Chassis B58

T#:5095728

Part#: GCHASB58HEATEXCH

Ships on Jul 15, 2025

$ 480.00 USD

Add to Wish List

Qty

$ 480.00 USD

Add to Wish List

This heat exchanger upgrade is a high-quality replacement that dramatically lowers engine oil and water temperatures by providing a 50% larger cooling surface than OEM. The benefits are most noticed during back to back runs at higher boost levels where the factory cooling capacity can be overwhelmed resulting in ignition timing pull and reduced turbo efficiency. Direct bolt-in installation.

Show More Show Less

BMS Billet Water/Methanol Injection Tank Cap With Safety Check Valve ...

T#:20815185

Part#: BMSWMITC

Ships in 3 Business Days

$ 59.00 USD

Add to Wish List

Qty

$ 59.00 USD

Add to Wish List

The Burger Motorsports custom billet Water/Methanol Injection (WMI) cap includes an integrated heavy-duty check valve to let much-needed air in and prevent dangerous WMI vapor/fumes and liquid from getting out! Each cap is CNC machined in the USA from a solid block of billet aluminum, engraved with the BMS logo, and anodized blue for protection. Check valve piston must be lightly lubricated if tank shows signs of vacuum. One drop of penetrating oil or motor oil in the top will keep the check valve operational. Features and Benefits Integrated heavy-duty check valve lets air in but not out Specifically designed to prevent evaporation Keeps vapors inside the tank Made from a solid block of billet aluminum Blue anodizing for corrosion protection Exaggerated grips for easy removal Integrated heavy-duty o-ring Made in the USA

Show More Show Less

2 Gallon Low Profile Universal Methanol Tank

T#:20946755

Part#: 2G-ULPMT

Ships on Jul 14, 2025

Starting at $ 179.00 USD

Add to Wish List

Starting at $ 179.00 USD

Add to Wish List

Integrated pump mount for a super clean install. This tank allows the pump (sold separately) to mount to the bottom of the tank making for a clean and fast installation. It’s universal and will fit a wide variety of trunk applications. The larger capacity means more time between fill ups. Offered in black for a stealth appearance and in clear to allow visually checking the fluid level. Includes a 2-way vented black plastic cap and a compression pump feed fitting. Compatible with BMS DDP5800 pumps, ES4714512 or ES4714513 Optional upgraded blue billet water/methanol injection (WMI) cap with 1-way check valve, ES4714530 Pump mounts directly to the tank Compatible with all DDP 5800 pumps Super low profile design Available in clear for visually checking fluid levels Available in black for a stealth appearance Includes 2-way vented black plastic cap 4 mounting holes in the feet of the tank Includes a compression pump feed fitting, 2 90 degree push fittings, 9" of methanol line and pump mounting hardware. Made in the USA Tank dimensions: L 15.5" x W 8" x H 8.25"

Show More Show Less

1.25 Gallon Heavy-Duty Universal Methanol Tank

T#:20946761

Part#: 1.25G-UMT-CL

Ships on Jul 15, 2025

$ 69.00 USD

Add to Wish List

Qty

$ 69.00 USD

Add to Wish List

This tank is thicker and stronger than BMS' basic 1-gallon WMI tank. This tank features an easy fill filler nozzle, an anti-starvation reservoir with a pre-threaded bung for the included 90º compression pump feed fitting, a spill-catcher reservoir around the filler cap, a 2-way vented black plastic cap, and is translucent to allow visually checking the fluid level. Optional upgraded blue billet water/methanol injection (WMI) cap with 1-way check valve, ES4714530 Features & Benefits 1.25 Gallon Tank (4.73 Liters) Anti-Starvation Reservoir Easy Fill filler Nozzle Spill-Catcher Reservoir around the filler cap Available in clear for visually checking fluid levels 8 mounting holes on the side rails Includes 2-way vented black plastic cap Includes a 90º compression pump feed fitting Tank dimensions: L 11" x W 4.5 x H 9"

Show More Show Less

BMS JB4 Port Injection Controller - F/G Chassis

T#:21012590

Part#: F-G-PORTINJCONMO

In Stock

$ 349.00 USD

Add to Wish List

Qty

$ 349.00 USD

Add to Wish List

The Burger Motorsports JB4 Port Injection Controller attaches to the JB4 allowing it to directly control both traditional port injection kits and WMI port injection kits. The JB4 port injection controller is a fully integrated solution allowing enhanced port injection mapping and safety. For example the JB4 port injection controller: 1) Uses low fuel pressure in conjunction with boost pressure to evaluate injection pressure and adjust PI IPW dynamically as required to maintain consistent flow volume. This becomes particularly important in applications that are at the edge of their low fuel pressure supply. As low pressure drops or oscillates port injection IPW must be dynamically adjusted to avoid run lean conditions. 2) Monitors pedal input, clutch input, gear, throttle position, etc, allowing more advanced mapping and instant cut of PI when letting off the gas or when traction control kicks in to avoid backfires. 3) Monitors AFR in both banks and can cut PI flow in the event a misfire event is detected preventing a potentially lean condition. 4) Monitors current through the injectors and sends a signal back to the JB4 altering it of various problems including a clogged or disconnected injector, blown electrical fuse, loose ground, etc. 5) Monitors fuel trims in each bank and failsafe's in the event of a mismatch of more than 15% indicating a potential boost single cylinder boost leak or injector flow issue. 6) Allows easy user adjustment of overall fuel volume using linear "Fuel Bias 0-100" values by RPM, greatly reducing the typical mapping complications when making manual tuning changes. 7) Integrates into the JB4 multi-map system which produces on-the-fly PI mapping changes when you change maps when boost is reduced in lower gears, or during anti-lag engagement. 8) When equipped with a JB4 integrated flex fuel sensor or JB4 virtual flex fuel sensor can automatically adjust port injection volume based on the E85 mixture allowing for easy mixture changes. 9) Enhanced mapping logic such as tip in supplement to boost port injection during sudden transitions like spool up or gear changes where the high-pressure pump tends to have problems keeping up. 10) Does not require a separate interface and cable for mapping and tuning port injection. It's all done right through the JB4 interface and logs greatly simplifying the process. 11) Includes an extra output to run your second fuel pump OR WMI PUMP (for port injection meth), eliminating the need for an extra Hobbs switch.

Show More Show Less

Burger Motorsport JB4-Compatible Water/Methanol Injection System - N2...

T#:558163

Part#: BMS-WMI

Ships in 1-3 days

Starting at $ 226.99 USD

Add to Wish List

Starting at $ 226.99 USD

Add to Wish List

Looking to make loads of power on pump gas? Enter: water/methanol injection. Regardless if you're tuned for conventional pump gas, E85, or race fuel, use of a properly configured and integrated water/meth system will reduce temperatures, allowing you to make more power than on just conventional fuel alone. Select your engine-specific nozzles (which are standard 1/8" NPT and install in most aftermarket chargepipes), your tank to mount in the trunk, upgraded steel braided lines if you so choose, and some boost juice and you just need a management solution! Optionally, add a BMS FSB for JB4 integration!

Show More Show Less

BMS DDP5800 Water/Methanol Injection Pump

T#:20815186

Part#: BMSDDP5800

Ships in 1-3 days

Starting at $ 120.00 USD

Add to Wish List

Starting at $ 120.00 USD

Add to Wish List

The Burger Motorsports DDP 5800 water methanol alcohol Injection pump is a heavy-duty pump used in all of our BMS Water Injection kits. 200 psi bypass for smooth and high pressure and 1.3 GPM open flow. Made in the USA. Available with built-in quick connect fittings for 1/4" WMI line or with open 3/8" NPT threads if you plan to use braided lines.

Show More Show Less

1 Gallon Methanol Tank - Clear/White

T#:558165

Part#: 1G-MT-CL

Ships Jul 8, 2025

$ 30.00 USD

Add to Wish List

Qty

$ 30.00 USD

Add to Wish List

The least expensive option available from BMS, this 1 gallon tank is compact and flexible allowing for a wide range of mounting on any flat vertical surface in the trunk. The tank is clear to allow visually checking the fluid level. Includes a 2-way vented black plastic cap and a compression pump feed fitting. Optional upgraded blue billet water/methanol injection (WMI) cap with 1-way check valve, ES4714530 Features & Benefits Available in clear for visually checking fluid levels 8 mounting holes on the side rails Includes 2-way vented black plastic cap Includes a compression pump feed fitting Made in USA Tank dimensions: L 11" x W 4.5 x H 9"

Show More Show Less

BMS Water/Methanol Injection (WMI) Solenoid W/ Filter

T#:21176934

Part#: BMS-WMI-SOL

In Stock

$ 75.00 USD

Add to Wish List

Qty

$ 75.00 USD

Add to Wish List

This solenoid safely stops fluid from flowing into your intake system when WMI is not in use. The solenoid features two 1/8 NPT ports with included compression 1/4 in. hose fittings for a quick leak-free connection. The included filter keeps dirt and debris out of your engine.

Show More Show Less

Water/Methanol Injection Hose - 20'

T#:21176944

Part#: BMS-WMI-IL

In Stock

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

BMS Water/Methanol Injection (WMI) Kit - Gen 2 B58

T#:21308437

Part#: WMIK-B58G2

Ships on Jul 14, 2025

Starting at $ 799.00 USD

Add to Wish List

Starting at $ 799.00 USD

Add to Wish List

Make tremendous amounts of power on pump gas! Everything you need to get started with WMI in one convenient kit. JB4 compatible! Water/Methanol/Alcohol injection commonly referred to as WMI allows you to make tremendous amounts of power on pump gas. The effect is similar to running 100 octane race gas or E85 fuel all the time with the additional cooling benefits allowing for more power than you can make on race gas or E85 alone. For those that don't have easy E85 access WMI adds a on of power over pump gas, and for those running E85 WMI can still be very useful for its charge air cooling and fuel volume benefits. The key to a safe and effective WMI setup is tuning integration. The B58 BMS WMI kit integrates to the JB4 tuning system allowing for precise mapping based on boost, throttle position, engine speed, intake temperature, advance, gear, and other data elements available to the JB4 through its CANbus system. In addition, a pump flow signal is fed back to the JB4 allowing for a safe and smooth progressive boost mapping. If the tank runs empty or flow drops for any reason the JB4 will safely back down performance to avoid detonation. Boost is held low until WMI is properly flowing to avoid tip in knock common with non-integrated WMI setups. In addition WMI can be activated or disabled right from the JB4 Mobile app and will automatically disengage during traction control or safety map situations. WMI flow data can be displayed via your JB4 Mobile logging device. This water/methanol injection (WMI) tank is a completely custom design that neatly hides away in the left side trunk cavity found in most G20 G22 & G80 M3 & G82 M4 BMW vehicles. The pump mounts directly to the back of the tank allowing for a quick, clean, and completely stealth installation. The bottom of the tank includes a rear sump allowing for consistent performance even as the tank drains. Includes 2-way vented black plastic cap, a compression pump feed fitting, and 12" of vinyl WMI line for the non-pressure side of the WMI pump. This kit includes a BM10 (10 GPH or approx. 750 ml/min) injection nozzle suitable for most B58 applications. Mounting requires an 1/8" NPT port or the throttle plate adapter. What's included (1) G20 Stealth Tank and Mounting Hardware (1) FSB JB4 Water/Methanol Injection Controller (1) BMS water/methanol Injection pump (1) BM10 Water/Methanol Nozzle (1) 12.5' of steel braided hose (straight and 90º fitting) (1) 2' of steel braided hose (straight and 90º fitting) (1) 18" of PTFE line (tank to pump) (1) Billet 1/4 push male to -4AN male 90º (pump out) (1) 1/4 push male to female 90º (pump in) (1) Solenoid (1) 15' (-) Negative black wire (1) 15' (+) Positive red wire (7) wire wire nuts (1) inline fuse holder

Show More Show Less

Super Atomizing Water/Methanol Injection Nozzles

T#:20815192

Part#: BMS.SA.WMI.NOZ

Ships on Jul 14, 2025

Starting at $ 40.00 USD

Add to Wish List

Starting at $ 40.00 USD

Add to Wish List

With CNC machined serviceable/cleanable nozzle inserts for precise fluid metering. Choose single or dual nozzles and match the flow rate to your power needs! Water/Methanol Injection (WMI) nozzles are determined by the intended power and how many bungs your charge pipe has. These nozzles are 1/8” NPT and screw in to bungs included on most aftermarket charge pipes. BMS "super atomizing" nozzles are designed and manufactured by BMS and are known for their great atomization and flow characteristics. The number on the methanol injection nozzle represents the approximate gallons per hour of fluid when at full flow. Generally speaking running two smaller nozzles is preferred to one larger nozzle for an equal flow to improve fluid atomization and distribution.

Show More Show Less

WMI Inline Filter

T#:21176933

Part#: BMS-WMI-FIL

Ships on Jul 15, 2025

$ 15.00 USD

Add to Wish List

Qty

$ 15.00 USD

Add to Wish List

This heavy duty methanol/water injection filter is specifically designed for a methanol/water system can filter particles down to 40 microns in size. It safeguards the functional components of the water/methanol system as well as your engine from particulates present in the water/methanol mixture.

Show More Show Less

BMS 3.5 Gallon Stealth Water/Methanol Injection (WMI) Tank

T#:20815187

Part#: BMW35G28

Ships on Jul 14, 2025

Starting at $ 279.00 USD

Add to Wish List

Starting at $ 279.00 USD

Add to Wish List

Safe, sleek, and ready to install out of the box! Your choice of color and accessories! This water/methanol injection (WMI) tank is a completely custom design that neatly hides away in the left side trunk cavity found in most G20 G22 & G80 M3 & G82 M4 BMW vehicles. The pump mounts directly to the back of the tank allowing for a quick, clean, and completely stealth installation. The bottom of the tank includes a rear sump allowing for consistent performance even as the tank drains. Includes 2-way vented black plastic cap and a compression pump feed fitting. Optional upgraded blue billet water/methanol injection (WMI) with 1-way check valve (ES4714530) Burger Motorsports DDP 5800 water methanol alcohol Injection pump (ES4714532) Features & Benefits Leaves trunk completely clear for full use of space Super low profile design tucks neatly into the existing left side trunk cavity 3.5 Gallon (13.25 liters) capacity Available in transparent white for visually checking fluid levels and opaque black for a stealth appearance. DDP 5800 pump mounts directly to the tank (pump sold separately) Tank dimensions: L 20.5" x W 11" X H 13.5" What's included: (1) Stealth Tank (1) 2-way vented black plastic filler cap (1) brass Compression Tube Fitting for 1/4" Tube OD x 1/4 NPT Male (1) 18" of line (2) Powder coated stainless lower bracket (2) Rubber lower bracket grommets (2) BMS custom bell washers (2) Stainless Steel Flanged Button Head Screws M6 x 1 mm Thread, 8 mm Long (1) Plastic upper bracket (2) Self Tapping upper bracket screws 1/4" Size, 1-1/2" Long (4) Pump Screws - Phillips Passivated Stainless 10-32 Thread, 1-1/4" Long (2) 1/4 push male to female 90º to pump in (1) Button Head Hex Drive Screw 18-8 Stainless M8 x 1.25 Thread Size, 15mm Long (bracket to chassis) (1) Nylon lock nut - M8 x 1.25 mm Thread, 9.5 mm High (bracket to chassis) (1) Button Head Hex Drive Screw Passivated 18-8 Stainless Steel, M10 x 1.50 mm Thread, 16mm Long (bracket to chassis)

Show More Show Less

Billet Water/Methanol Injection (WMI) Spacer - Gen 2 B58

T#:20782258

Part#: BMSB58WMISPG2

Ships on Jul 15, 2025

$ 99.00 USD

Add to Wish List

Qty

$ 99.00 USD

Add to Wish List

Normally you'd replace the factory charge pipe to install a water/methanol kit but in the case of the B58 engine, the factory charge pipe is very sturdy and difficult to remove. So we've designed this plug and play adapter for quick installation and removal of BMS dual nozzle water/meth kits without having to replace the factory charge pipe. Simply unscrew three bolts, insert the CNC machined adapter with integrated o-ring in place, and tighten the included longer length bolts, to allow mounting of two meth nozzles with a perfect seal. Includes dual 1/8" NPT methanol bungs appropriately machined for a clean spray pattern which is critical for proper atomization with the B58 motor. For most B58 water/methanol applications we suggest dual CM5 nozzles.

Show More Show Less

BMS Universal Water/Methanol Injection (WMI) Kit - Flash Only ...

T#:21176943

Part#: BMS-WMI-UNFO

Ships on Jul 15, 2025

$ 229.00 USD

Add to Wish List

Qty

$ 229.00 USD

Add to Wish List

Project Cars

SELECT YOUR BMW

BMW Intake Parts for BMW 3 Series G20 (2019+)

Sub-Categories

BMS Elite Charge Pipe w/o BOV - B58 Gen 2

BMS G20 B58 Billet Intake

BMS Elite Charge Pipe W/ Turbosmart Raceport BOV- B58 Gen 2 ...

BMS Elite Charge Pipe - B58 Gen 2

BMW G20 B58 3.0L BMS Competition Cold Air Intake - Blue

BMS Silicone Intake Pipe Hose Upgrade - G Chassis B58

Autotecknic Dry Carbon Fiber Cooling Shroud - G20 330I/xDrive ...

Burger Motorsports Competition Cold Air Intake B48 BMW 230i 330i 430i...

BMS Competition Cold Air Intake - Red - B58 G Chassis

Burger Motorsports Competition Cold Air Intake B58 BMW M240i M340i M4...

Burger Motorsports Competition Cold Air Intake B58 BMW M240i M340i M4...

BMS Heat Exchanger Upgrade - G-Chassis B58

BMS Billet Water/Methanol Injection Tank Cap With Safety Check Valve ...

2 Gallon Low Profile Universal Methanol Tank

1.25 Gallon Heavy-Duty Universal Methanol Tank

BMS JB4 Port Injection Controller - F/G Chassis

Burger Motorsport JB4-Compatible Water/Methanol Injection System - N2...

BMS DDP5800 Water/Methanol Injection Pump

1 Gallon Methanol Tank - Clear/White

BMS Water/Methanol Injection (WMI) Solenoid W/ Filter

Water/Methanol Injection Hose - 20'

BMS Water/Methanol Injection (WMI) Kit - Gen 2 B58

Super Atomizing Water/Methanol Injection Nozzles

WMI Inline Filter

BMS 3.5 Gallon Stealth Water/Methanol Injection (WMI) Tank

Billet Water/Methanol Injection (WMI) Spacer - Gen 2 B58

BMS Universal Water/Methanol Injection (WMI) Kit - Flash Only ...

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results