Oiling System for BMW G42 M240i xDrive B58 3.0L

Clear BMW chassis

Tasked with keeping everything properly lubricated, the oiling system is one of the most if not THE most fundamental parts of the engine. Make sure that everything is in good working order and flowing properly to ensure your engine has a long and trouble-free service life.

Sub-Categories

Sort By:

MMX Oil Filler Cap - Black

For Most BMW Models 2007 Onwards or Mini Models

T#:4552062

Part#: MMR03-0102-BL

In Stock

$ 127.99 USD

Add to Wish List

Qty

$ 127.99 USD

Add to Wish List

MMX's Performance billet oil filler cap machined from billet T-6061 aluminum has been designed to instantly give your engine bay an subtle aesthetic upgrade. This cap comes in a Black finish. *Note: After exposure to excessive heat over prolonged periods, overall finish fading can occur. Reusing of original seal is required.

Show More Show Less

MMX High Performance Oil Filter - BMW B58 & B58TU

T#:29035359

Part#: MMR17-1502

Special Order: No Guaranteed ETA

$ 81.99 USD

Add to Wish List

Qty

$ 81.99 USD

Add to Wish List

Get rid of the notorious B58 oil filter disintegration problem forevermore with the MMR Performance Oil Filter. By replacing the factory paper filter element with MMR’s advanced high-flow, high-filtration stainless steel filter unit, you will protect your engine from the big bills (and potentially worse) caused by the OE filter’s collapse failure. The oil filters on BMW’s B58 & B57 3.0 6-cylinder engines (both petrol and diesel) suffer from a well-documented quality problem with the factory paper-element oil filter. At service time, when removal of the filter is attempted, the bottom section frequently breaks away from the disintegrated filtration material. This leaves the broken base stuck in the oil filter housing and an expensive removal/replacement job to extract the remains and fit a new housing. Such is the problem that there’s even an official BMW technical bulletin to warn their dealers of this. The MMR replacement Oil Filter is a pretty special replacement filter. It fixes this annoying problem once and for all. The MMR Oil Filter element is made from a pleated high-flow stainless steel micronic filter cloth – a medical-grade material guaranteed to filter out oil contamination right down to 20 Microns, ensuring far better protection than paper-based filters can achieve. As well as this exceptional filtration, the filter material allows for five times the flow of comparable paper oil filters. Its design provides consistent filtering across entire filter surface. The failure of the factory oil filter generally just leads to a large bill to extract the damaged remnants. However, more worryingly, it has occasionally been known to lead to broken pieces of filter media running through the small oilways and orifices of the engine’s lubrication system, risking blocking the oil running round the bearings and VANOS system and causing much greater mechanical damage before it is caught. The MMR Oil Filter is a reusable unit which can be used over and over again. As long as it is thoroughly cleaned at each oil change, it will last the lifetime of the vehicle and keep on protecting the engine just as it did when new. However, proper cleaning is not necessarily a DIY job, as it requires the use of a suitable solvent to break down the old oil, and cleaning from the inside out with compressed air to remove any risk of debris remaining. If you have any doubts about this, we recommend as best-practice to change filter with every oil-change. The MMR Oil Filter is a lifetime reusable filter. But to resuse and avoid any future loss of filtration or oil flow, it is essential that it is thoroughly cleaned at each oil change as follows: Remove MMR Oil Filter from filter housing Remove 3x O-Rings from MMR Oil Filter prior to Step 3, as fuel will degrade and cause damage to these rubber/Viton components. Soak the filter one of the following fluids for 5-10 minutes – Petrol/Gasoline or Carb Cleaner or Soap and Water Agitate/stir every few minutes until the outer surface is free of any engine debris Dry the filter using compressed air, blow air through the filter, (do not press the compressed air gun against the filter, keep at least a 10mm gap from nozzle to filter) starting from the inside out, then at an angle on the outside of the screen to further remove any remaining particles or cleaning solution. Once dry, reinstall O-Rings (MMR advices replacement of these O-Rings every oil service - See ES4810064) and refit into oil filter housing and engine. If you have any doubt about your ability to perform this sequence, we recommend replacing the filter element with each oil change.

Show More Show Less

Oil Drain Plug

10X Entries Into Our F80 M3 Sweepstakes

T#:41188174

Part#: 11137535106TKT

In Stock

Sale - Save 33% $ 8.99

This product was last offered at the strikethrough price on
05-03-2026

$ 6.00 USD

Add to Wish List

Qty

Sale - Save 33%

$ 8.99

This product was last offered at the strikethrough price on
05-03-2026

$ 6.00 USD

Add to Wish List

Includes a one time use crush washer.

Oil Filter Housing Gasket Replacement Kit - BMW Gen1 and Gen2 B58 3.0...

10X Entries Into Our F80 M3 Sweepstakes

T#:27871828

Part#: 11428583896TKT

Ships in 2 Business Days

Sale - Save 2% $ 150.99

This product was last offered at the strikethrough price on
08-26-2026

$ 148.42 USD

Add to Wish List

Qty

Sale - Save 2%

$ 150.99

This product was last offered at the strikethrough price on
08-26-2026

$ 148.42 USD

Add to Wish List

One unfortunate problem BMW failed to address with the B58 engines is leaking oil filter housing gaskets. If your oil filter housing gaskets are leaking, you will notice a slow oil loss, pooling oil under your vehicle, and oil running down the left rear side of your engine block and on the side of your oil pan. This kit includes all-new gaskets to re-seal your filter housing plus Liqui-Moly oil and a new Hengst filter to get your car back up and running and leak-free!

Show More Show Less

MMX Performance Billet Oil Filler Cap

T#:28968889

Part#: MMR03-1601

Special Order: No Guaranteed ETA

$ 127.99 USD

Add to Wish List

Qty

$ 127.99 USD

Add to Wish List

O-Ring Replacement Kit For MMX Performance Filter - BMW B58 & B58TU ...

T#:29035360

Part#: MMR17-0000

Special Order: No Guaranteed ETA

$ 13.99 USD

Add to Wish List

Qty

$ 13.99 USD

Add to Wish List

Genuine MMR Performance O-Ring service kit for the MMX Performance oil filter and billet housing. Does not include MMR oil filter or billet housing, only the four O-Rings needed to service our reusable filter. The MMR Performance oil filter and housing contains four O-Rings within the kit. We recommend you replace the O-Ring set on a regular basis when changing or cleaning the MMR filter, in order to maintain the integrity of the sealing properties it was designed to provide. As it's a direct replacement with the original O-Ring set supplied, it's a very straightforward process to swap and replace. Fitment is limited to the MMR Performance oil filter (MMR17-1502 - See ES4810063) to protect against the notorious B58 oil filter collapse

Project Cars

SELECT YOUR BMW

Oiling System for BMW G42 M240i xDrive B58 3.0L

Sub-Categories

MMX Oil Filler Cap - Black

MMX High Performance Oil Filter - BMW B58 & B58TU

Oil Drain Plug

Oil Filter Housing Gasket Replacement Kit - BMW Gen1 and Gen2 B58 3.0...

MMX Performance Billet Oil Filler Cap

O-Ring Replacement Kit For MMX Performance Filter - BMW B58 & B58TU ...

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Narrow Results