BMW Intake Parts for BMW A90 MKV Supra B58 3.0L

BMS Elite Charge Pipe - BMW Gen2 B58 3.0L (B58TU / B58C / B58D) ...

T#:21209828

Part#: B58G2CP

Ships in 4 Business Days

Starting at $ 299.00 USD

Add to Wish List

Starting at $ 299.00 USD

Add to Wish List

Replace the failure prone plastic charge pipe that came on your car before it leaves you stranded! The BMS Elite B58TU charge pipe upgrade is constructed from high-gauge aluminum and features a CNC throttle body and turbo flange for a snug, OEM-style fit. It features a glossy black powder coat to coordinate with the engine bay and includes three 1/8" NPT bungs ideal for an external boost gauge or methanol nozzles. With a double o-ring seal design on the chargepipe flange that attaches to the turbo, this chargepipe is designed to withstand up to 40+psi of high boost. Also includes a heavy-duty replacement coupler, o-rings, clamps, and all required installation hardware. Now available with or without a Turbosmart Raceport BOV! The blow-off valve version releases excess pressure in the charge pipes when letting off the gas. In addition to intoxicating sound, it reduces compressor surge and improves overall reliability at higher boost levels. Compatible with factory tuning, JB4, and flash tuning. What's Included with the NON-BOV kit ES4715295: (see below for BOV kit) (1) Upper charge pipe (1) Lower charge pipe (1) 3R2.5 silicone coupler (1) 2.5" Tbolt clamp (1) 3" Tbolt clamp (3) 1/8NPT plugs (1) M6x1x16mm bolt (2) M6x1x20mm bolts (2) Small O rings (1) Large O ring What's Included with the BOV kit ES4715315: (1) Turbosmart Blow-Off Valve (1) Lower charge pipe (1) Upper charge pipe with BOV flange (1) 3R2.5 silicone coupler (1) 2.5" Tbolt clamp (1) 3" Tbolt clamp (5) 1/8NPT plugs (1) M6x1x16mm bolt (2) M6x1x20mm bolts (2) Small O rings (1) Large O ring (1) BOV adapter + E clip (2) 90* 1/8NPT to 1/4" push lock fittings (1) 30" 1/4" tubing

Show More Show Less

BMC Filter Cleaning Kit

T#:590913

Part#: WA250-500

In Stock

$ 24.99 USD

Add to Wish List

Qty

$ 24.99 USD

Add to Wish List

BMC Performance Air Filter - G20, Supra

T#:641644

Part#: FB01054

Back Ordered

$ 102.99 USD

Add to Wish List

Qty

$ 102.99 USD

Add to Wish List

Looking to upgrade your air filter for increased flow and performance? BMC filter allow significantly higher air flow and are perfectly molded in one piece to fit exactly the same as your stock air filter. These filters are constructed from multi-layerd cotton gauze that is pre-oiled and can be cleaned and regenerated using the BMC regeneration kit.

Show More Show Less

Vargas Billet B58 Vacuum/Boost Adapter - B58 3.0L

2X Entries Into Our F80 M3 Sweepstakes

T#:638811

Part#: VTT-B58-VACCUM

Ships in 10 Business Days

Starting at $ 52.99 USD

Add to Wish List

Starting at $ 52.99 USD

Add to Wish List

Vargas Turbo has released their very own BMW B58 vacuum/boost adapter. These go inline with the intake manifold fitting and provide a full boost/vacuum signal from the manifold. This fitting adds two 1/8" NPT bungs to accept any fitting that has 1/8" NPT threads. You can choose three configuration options: Fitting by itself Fitting with one 1/4" barb and one plug Fitting with two 1/4" barbs Once installed it tucks perfectly under your engine cover. These are perfect for running your PI switch off manifold pressure, which is much more accurate than the charge pipe, and they are also great for BOVs running the proper size line without having to drill a hole in your manifold. These do space out any sensors etc giving inaccurate readings like some of the other brands do.

Show More Show Less

BMS Billet Intake For B58 - Z4/ Supra - Red

T#:38857229

Part#: BMS-B58BI-R

Ships on Oct 27, 2026

$ 199.00 USD

Add to Wish List

Qty

$ 199.00 USD

Add to Wish List

Unlock up to 8whp with this plug-and-play air intake system, designed to enhance power, throttle response, and turbo spool while delivering an aggressive turbo sound under acceleration. Crafted from CNC-machined billet aluminum and anodized black for a sleek finish, this intake features a reusable S&B high-flow inverted cone filter for maximum airflow. The OEM cold air intake tube remains fully functional, ensuring optimal efficiency. Key Features & Benefits: ✅ Adds up to 8whp for increased performance ✅ Enhances throttle response & turbo spool ✅ Dramatic sound improvement – hear your turbo spool up ✅ High-quality CNC-machined billet aluminum construction ✅ Sleek black anodized finish for a clean look ✅ Reusable S&B high-flow inverted cone filter ✅ Quick & fully reversible installation in minutes 🔧 Made in the USA – Built for Performance Enthusiasts! 🔥

Show More Show Less

Burger Motorsports Billet Intake - A90 Supra G29 Z4

T#:588195

Part#: BMSA90INF

Ships on Oct 27, 2026

$ 229.00 USD

Add to Wish List

Qty

$ 229.00 USD

Add to Wish List

VTT Single Piece Silicone Charge Pipe w/o BOV - B58

2X Entries Into Our F80 M3 Sweepstakes

T#:21209815

Part#: VTT-A90CP

Ships in 10 Business Days

Starting at $ 345.99 USD

Add to Wish List

Starting at $ 345.99 USD

Add to Wish List

6-ply, Heat Resistant, Wire reinforced silicone charge pipes rated at over 200 psi This system completely does away with the restrictive, and muli-connection stock charge pipe system, and replaces it with a single 6-ply, Heat Resistant, Wire reinforced silicone charge pipes rated at over 200 psi. They are molded for the perfect fit in your engine bay, while not sacrificing anything in the way of flow or size. They also completely isolate your charge air from any additional heat soak coming in from the engine or ambient heat. Another huge benefit is your vehicle goes from 4 connections to only TWO which are barbed and has many small ridges which dig into the silicone so it’s impossible for the pipe to blow off. This means no more blown charge pipe connections on the track or road leaving you stranded. There are other options on the market, but they only address the problem in half measures. Some offer silicone connectors that are attached to hard pipes and are notorious for blowing, but they do nothing to address the heat soak issue or the number of connections needed. This kit solves ALL of those problems and does so at a lower cost. Install is very easy and takes about an hour if you are inexperienced with working on your own car, can take as little as 30-45 minutes if you have had it apart a few times. Dimensions for the pipes are as follows: Hot Side Pipe: 64mm or 2.50' on the connection to the turbo outlet opening up immediately to 77mm or 3' and remaining a FULL 3' to the throttle body inlet. Note: These will fit all aftermarket manifolds BMS has tested, some require slight trimming of the 3' end The kit includes: VTT Hot Side Silicone Charge pipe 2 VTT Branded CNC adapters to mount the map sensor, and Temp Probe 2 VTT Branded CNC adapters for the Turbocharger outlet, and TB inlet 2 VTT branded T-Bolt Clamps 2 1/8 NPT ports are included in the TB flange for methanol

Show More Show Less

Intake System

2X Entries Into Our F80 M3 Sweepstakes

T#:2928964

Part#: SUPRA-INT-1

Ships in 10 Business Days

$ 388.99 USD

Add to Wish List

Qty

$ 388.99 USD

Add to Wish List

Billet Intake For B58 - Z4/ Supra

T#:38857221

Part#: BMS-B58BI-B

Ships on Oct 27, 2026

$ 199.00 USD

Add to Wish List

Qty

$ 199.00 USD

Add to Wish List

Unlock up to 8whp with this plug-and-play air intake system, designed to enhance power, throttle response, and turbo spool while delivering an aggressive turbo sound under acceleration. Crafted from CNC-machined billet aluminum and anodized black for a sleek finish, this intake features a reusable S&B high-flow inverted cone filter for maximum airflow. The OEM cold air intake tube remains fully functional, ensuring optimal efficiency. Key Features & Benefits: ✅ Adds up to 8whp for increased performance ✅ Enhances throttle response & turbo spool ✅ Dramatic sound improvement – hear your turbo spool up ✅ High-quality CNC-machined billet aluminum construction ✅ Sleek black anodized finish for a clean look ✅ Reusable S&B high-flow inverted cone filter ✅ Quick & fully reversible installation in minutes 🔧 Made in the USA – Built for Performance Enthusiasts! 🔥

Show More Show Less

VTT Carbon Fiber Airbox Lid & Filter Kit - G20, G29, A90 B58 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:29334009

Part#: VTT-G2X-CF-LID-1

Ships in 10 Business Days

$ 444.99 USD

Add to Wish List

Qty

$ 444.99 USD

Add to Wish List

Enhance your engine bay's aesthetics with the sleek carbon fiber airbox lid from Vargas Turbo Technologies!

VTT rigorously tested the stock air intake on a dynamometer and found limited areas for enhancement. Drawing inspiration from BMW's design, VTT crafted a carbon fiber lid for the factory airbox.

Constructed entirely from 100% carbon fiber, this lid features an eight-layer design with a 1.3mm thick UV-resistant shell, ensuring long-lasting durability.

The included high-performance air filter, made from a high-flow cotton weave, comes pre-oiled to trap contaminants while maintaining optimal airflow.

Key Features:

50-state emissions compliant Simple, straightforward installation Stunning carbon fiber appearance Reusable high-performance air filter Easily reversible upgrade Transform your B58-equipped BMW with the Carbon Fiber Airbox Lid & Filter Kit from Vargas Turbo Technologies today!

Show More Show Less

BMS Heat Exchanger Upgrade - G-Chassis B58

T#:5095728

Part#: GCHASB58HEATEXCH

Ships on Oct 27, 2026

$ 480.00 USD

Add to Wish List

Qty

$ 480.00 USD

Add to Wish List

This heat exchanger upgrade is a high-quality replacement that dramatically lowers engine oil and water temperatures by providing a 50% larger cooling surface than OEM. The benefits are most noticed during back to back runs at higher boost levels where the factory cooling capacity can be overwhelmed resulting in ignition timing pull and reduced turbo efficiency. Direct bolt-in installation.

Show More Show Less

VTT Single Piece Silicone Charge Pipe W/ BOV - B58

2X Entries Into Our F80 M3 Sweepstakes

T#:21209830

Part#: VTT-A90CPV

Ships in 10 Business Days

Starting at $ 397.99 USD

Add to Wish List

Starting at $ 397.99 USD

Add to Wish List

This system completely does away with the restrictive, and muli-connection stock charge pipe system, and replaces it with a single 6-ply, Heat Resistant, Wire reinforced silicone charge pipes rated at over 200 psi. They are molded for the perfect fit in your engine bay, while not sacrificing anything in the way of flow or size. They also completely isolate your charge air from any additional heat soak coming in from the engine or ambient heat. Another huge benefit is your vehicle goes from 4 connections to only TWO which are barbed and has many small ridges which dig into the silicone so it’s impossible for the pipe to blow off. This means no more blown charge pipe connections on the track or road leaving you stranded. There are other options on the market, but they only address the problem in half measures. Some offer silicone connectors that are attached to hard pipes and are notorious for blowing, but they do nothing to address the heat soak issue or the number of connections needed. This kit solves ALL of those problems and does so at a lower cost. Install is very easy and takes about an hour if you are inexperienced with working on your own car, can take as little as 30-45 minutes if you have had it apart a few times. Dimensions for the pipes are as follows: Hot Side Pipe: 64mm or 2.50' on the connection to the turbo outlet opening up immediately to 77mm or 3' and remaining a FULL 3' to the throttle body inlet. Note: These Pipes Will Fit All Aftermarket Manifolds We Have Tested, Some Require Slight Trimming Of The 3' End The kit includes: VTT Hot Side Silicone Charge pipe 2 VTT Branded CNC adapters to mount the map sensor, and Temp Probe 2 VTT Branded CNC adapters for the Turbocharger outlet, and TB inlet 2 VTT branded T-Bolt Clamps 2 1/8 NPT ports are included in the TB flange for methanol

Show More Show Less

Vargas Carbon Fiber Airbox Lid & Filter Kit - BMW G29 Z4, Toyota A90/...

2X Entries Into Our F80 M3 Sweepstakes

T#:51778121

Part#: VTT-SUPRA-CF-LID

Ships in 10 Business Days

$ 444.99 USD

Add to Wish List

Qty

$ 444.99 USD

Add to Wish List

Elevate the performance and visual appeal of your B58-powered Supra or Z4 with the VTT Carbon Fiber Intake Lid and Filter system.

BMS Billet Water/Methanol Injection Tank Cap With Safety Check Valve ...

T#:20815185

Part#: BMSWMITC

In Stock

$ 59.00 USD

Add to Wish List

Qty

$ 59.00 USD

Add to Wish List

The Burger Motorsports custom billet Water/Methanol Injection (WMI) cap includes an integrated heavy-duty check valve to let much-needed air in and prevent dangerous WMI vapor/fumes and liquid from getting out! Each cap is CNC machined in the USA from a solid block of billet aluminum, engraved with the BMS logo, and anodized blue for protection. Check valve piston must be lightly lubricated if tank shows signs of vacuum. One drop of penetrating oil or motor oil in the top will keep the check valve operational. Features and Benefits Integrated heavy-duty check valve lets air in but not out Specifically designed to prevent evaporation Keeps vapors inside the tank Made from a solid block of billet aluminum Blue anodizing for corrosion protection Exaggerated grips for easy removal Integrated heavy-duty o-ring Made in the USA

Show More Show Less

1 Gallon Methanol Tank - Clear/White

T#:558165

Part#: 1G-MT-CL

In Stock

$ 30.00 USD

Add to Wish List

Qty

$ 30.00 USD

Add to Wish List

The least expensive option available from BMS, this 1 gallon tank is compact and flexible allowing for a wide range of mounting on any flat vertical surface in the trunk. The tank is clear to allow visually checking the fluid level. Includes a 2-way vented black plastic cap and a compression pump feed fitting. Optional upgraded blue billet water/methanol injection (WMI) cap with 1-way check valve, ES4714530 Features & Benefits Available in clear for visually checking fluid levels 8 mounting holes on the side rails Includes 2-way vented black plastic cap Includes a compression pump feed fitting Made in USA Tank dimensions: L 11" x W 4.5 x H 9"

Show More Show Less

BMS DDP5800 Water/Methanol Injection Pump

T#:20815186

Part#: BMSDDP5800

Ships in 1 Business Day

Starting at $ 120.00 USD

Add to Wish List

Starting at $ 120.00 USD

Add to Wish List

The Burger Motorsports DDP 5800 water methanol alcohol Injection pump is a heavy-duty pump used in all of our BMS Water Injection kits. 200 psi bypass for smooth and high pressure and 1.3 GPM open flow. Made in the USA. Available with built-in quick connect fittings for 1/4" WMI line or with open 3/8" NPT threads if you plan to use braided lines.

Show More Show Less

2 Gallon Low Profile Universal Methanol Tank

T#:20946755

Part#: 2G-ULPMT

In Stock

Starting at $ 179.00 USD

Add to Wish List

Starting at $ 179.00 USD

Add to Wish List

Integrated pump mount for a super clean install. This tank allows the pump (sold separately) to mount to the bottom of the tank making for a clean and fast installation. It’s universal and will fit a wide variety of trunk applications. The larger capacity means more time between fill ups. Offered in black for a stealth appearance and in clear to allow visually checking the fluid level. Includes a 2-way vented black plastic cap and a compression pump feed fitting. Compatible with BMS DDP5800 pumps, ES4714512 or ES4714513 Optional upgraded blue billet water/methanol injection (WMI) cap with 1-way check valve, ES4714530 Pump mounts directly to the tank Compatible with all DDP 5800 pumps Super low profile design Available in clear for visually checking fluid levels Available in black for a stealth appearance Includes 2-way vented black plastic cap 4 mounting holes in the feet of the tank Includes a compression pump feed fitting, 2 90 degree push fittings, 9" of methanol line and pump mounting hardware. Made in the USA Tank dimensions: L 15.5" x W 8" x H 8.25"

Show More Show Less

Burger Motorsport JB4-Compatible Water/Methanol Injection System - N2...

T#:558163

Part#: BMS-WMI

Ships on Oct 27, 2026

Starting at $ 226.99 USD

Add to Wish List

Starting at $ 226.99 USD

Add to Wish List

Looking to make loads of power on pump gas? Enter: water/methanol injection. Regardless if you're tuned for conventional pump gas, E85, or race fuel, use of a properly configured and integrated water/meth system will reduce temperatures, allowing you to make more power than on just conventional fuel alone. Select your engine-specific nozzles (which are standard 1/8" NPT and install in most aftermarket chargepipes), your tank to mount in the trunk, upgraded steel braided lines if you so choose, and some boost juice and you just need a management solution! Optionally, add a BMS FSB for JB4 integration!

Show More Show Less

1.25 Gallon Heavy-Duty Universal Methanol Tank

T#:20946761

Part#: 1.25G-UMT-CL

Ships on Oct 27, 2026

$ 69.00 USD

Add to Wish List

Qty

$ 69.00 USD

Add to Wish List

This tank is thicker and stronger than BMS' basic 1-gallon WMI tank. This tank features an easy fill filler nozzle, an anti-starvation reservoir with a pre-threaded bung for the included 90º compression pump feed fitting, a spill-catcher reservoir around the filler cap, a 2-way vented black plastic cap, and is translucent to allow visually checking the fluid level. Optional upgraded blue billet water/methanol injection (WMI) cap with 1-way check valve, ES4714530 Features & Benefits 1.25 Gallon Tank (4.73 Liters) Anti-Starvation Reservoir Easy Fill filler Nozzle Spill-Catcher Reservoir around the filler cap Available in clear for visually checking fluid levels 8 mounting holes on the side rails Includes 2-way vented black plastic cap Includes a 90º compression pump feed fitting Tank dimensions: L 11" x W 4.5 x H 9"

Show More Show Less

Water/Methanol Injection Hose - 20'

T#:21176944

Part#: BMS-WMI-IL

In Stock

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

BMS Water/Methanol Injection (WMI) Solenoid W/ Filter

T#:21176934

Part#: BMS-WMI-SOL

Ships on Oct 27, 2026

$ 75.00 USD

Add to Wish List

Qty

$ 75.00 USD

Add to Wish List

This solenoid safely stops fluid from flowing into your intake system when WMI is not in use. The solenoid features two 1/8 NPT ports with included compression 1/4 in. hose fittings for a quick leak-free connection. The included filter keeps dirt and debris out of your engine.

Show More Show Less

WMI Inline Filter

T#:21176933

Part#: BMS-WMI-FIL

Ships on Oct 27, 2026

$ 15.00 USD

Add to Wish List

Qty

$ 15.00 USD

Add to Wish List

This heavy duty methanol/water injection filter is specifically designed for a methanol/water system can filter particles down to 40 microns in size. It safeguards the functional components of the water/methanol system as well as your engine from particulates present in the water/methanol mixture.

Show More Show Less

Billet Water/Methanol Injection (WMI) Spacer - Gen 2 B58

T#:20782258

Part#: BMSB58WMISPG2

Ships on Oct 27, 2026

$ 99.00 USD

Add to Wish List

Qty

$ 99.00 USD

Add to Wish List

Normally you'd replace the factory charge pipe to install a water/methanol kit but in the case of the B58 engine, the factory charge pipe is very sturdy and difficult to remove. So we've designed this plug and play adapter for quick installation and removal of BMS dual nozzle water/meth kits without having to replace the factory charge pipe. Simply unscrew three bolts, insert the CNC machined adapter with integrated o-ring in place, and tighten the included longer length bolts, to allow mounting of two meth nozzles with a perfect seal. Includes dual 1/8" NPT methanol bungs appropriately machined for a clean spray pattern which is critical for proper atomization with the B58 motor. For most B58 water/methanol applications we suggest dual CM5 nozzles.

Show More Show Less

Super Atomizing Water/Methanol Injection Nozzles

T#:20815192

Part#: BMS.SA.WMI.NOZ

Ships on Nov 9, 2026

Starting at $ 40.00 USD

Add to Wish List

Starting at $ 40.00 USD

Add to Wish List

With CNC machined serviceable/cleanable nozzle inserts for precise fluid metering. Choose single or dual nozzles and match the flow rate to your power needs! Water/Methanol Injection (WMI) nozzles are determined by the intended power and how many bungs your charge pipe has. These nozzles are 1/8” NPT and screw in to bungs included on most aftermarket charge pipes. BMS "super atomizing" nozzles are designed and manufactured by BMS and are known for their great atomization and flow characteristics. The number on the methanol injection nozzle represents the approximate gallons per hour of fluid when at full flow. Generally speaking running two smaller nozzles is preferred to one larger nozzle for an equal flow to improve fluid atomization and distribution.

Show More Show Less

Project Cars

SELECT YOUR BMW

BMW Intake Parts for BMW A90 MKV Supra B58 3.0L

Sub-Categories

BMS Elite Charge Pipe - BMW Gen2 B58 3.0L (B58TU / B58C / B58D) ...

BMC Filter Cleaning Kit

BMC Performance Air Filter - G20, Supra

Vargas Billet B58 Vacuum/Boost Adapter - B58 3.0L

BMS Billet Intake For B58 - Z4/ Supra - Red

Burger Motorsports Billet Intake - A90 Supra G29 Z4

VTT Single Piece Silicone Charge Pipe w/o BOV - B58

Intake System

Billet Intake For B58 - Z4/ Supra

VTT Carbon Fiber Airbox Lid & Filter Kit - G20, G29, A90 B58 ...

BMS Heat Exchanger Upgrade - G-Chassis B58

VTT Single Piece Silicone Charge Pipe W/ BOV - B58

Vargas Carbon Fiber Airbox Lid & Filter Kit - BMW G29 Z4, Toyota A90/...

BMS Billet Water/Methanol Injection Tank Cap With Safety Check Valve ...

1 Gallon Methanol Tank - Clear/White

BMS DDP5800 Water/Methanol Injection Pump

2 Gallon Low Profile Universal Methanol Tank

Burger Motorsport JB4-Compatible Water/Methanol Injection System - N2...

1.25 Gallon Heavy-Duty Universal Methanol Tank

Water/Methanol Injection Hose - 20'

BMS Water/Methanol Injection (WMI) Solenoid W/ Filter

WMI Inline Filter

Billet Water/Methanol Injection (WMI) Spacer - Gen 2 B58

Super Atomizing Water/Methanol Injection Nozzles

Select Vehicle

Category

Brand

Price

Special Offers

Shipping

Narrow Results