BMW X Series E83 (2004-2010)

Bilstein Coil Over Spanner Wrench Set (Notch Style)

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:1702

Part#: 19101X

Ships in 1-2 days

$ 22.03 USD

Add to Wish List

Qty

$ 22.03 USD

Add to Wish List

Bilstein Coil Over wrench set for some PSS, PSS9 and PSS10 kits. Consists of a Large wrench and a Small wrench for adjusting the spring perch (76.25mm) and lock ring (75.75mm) on coil overs that require the rectangular notch style head (not round pin style adjuster). Can also be used with other coil over kits (H&R, Moton, JRZ, etc).

Show More Show Less

Bilstein B4 Rear. E83 X3 with Sport Suspension.

For vehicles with Sport suspension

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:344497

Part#: 19-234656

In Stock

$ 112.00 USD

Add to Wish List

Qty

$ 112.00 USD

Add to Wish List

Bilstein B4 OE Replacement Series gas pressure shocks and struts are specifically engineered to be the best choice for maintaining the original ride quality of your vehicle, while meeting or exceeding OE standards. These dampers are the ideal choice for the driver looking to restore the original performance and handling of their vehicle, with the added benefit of world-famous Bilstein quality.

Show More Show Less

B3 Rear Coil Spring - Priced Each

For vehicles with standard suspension

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:598653

Part#: 38-228599

In Stock

$ 74.00 USD

Add to Wish List

Qty

$ 74.00 USD

Add to Wish List

BMW has tuned a comfortable yet performance oriented suspension system across their model offering. The springs used are a very sophisticated design with both tapered wire diameter and progressive spring rates to ensure the best possible ride quality under varying loads and conditions. Due to environmental conditions, the original coating is commonly compromised thus creating a weak point which yields to failure (cracked springs). Replace your cracked springs with replacement parts from Bilstein.

Show More Show Less

Bilstein B6 Performance Rear Shock - E83 X3 2.5i, 3.0i, 3.0si, xDrive...

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:2295

Part#: BE5-B458-H1

Ships in 3 Business Days

$ 185.00 USD

Add to Wish List

Qty

$ 185.00 USD

Add to Wish List

Position: Rear, left or right
Setting: Performance, for stock suspensions

Rear Bilstein B6 Performance shock. Performance shocks are for cars with the standard, factory suspension. They are typically about 20% firmer than the original shock, improving body roll, brake dive, and overall handling. Includes top nut, stock dust boot is re-used. Price is per shock.

This Bilstein B6 Performance rear shock fits the following BMWs:
2004+ E83 X3 X3 2.5i, X3 3.0i, X3 3.0si, X3 xDrive30i

Show More Show Less

B3 Front Coil Spring - Priced Each

For vehicles with standard suspension

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:598652

Part#: 37-239817

Ships on Nov 5, 2026

$ 62.00 USD

Add to Wish List

Qty

$ 62.00 USD

Add to Wish List

BMW has tuned a comfortable yet performance oriented suspension system across their model offering. The springs used are a very sophisticated design with both tapered wire diameter and progressive spring rates to ensure the best possible ride quality under varying loads and conditions. Due to environmental conditions, the original coating is commonly compromised thus creating a weak point which yields to failure (cracked springs). Replace your cracked springs with replacement parts from Bilstein.

Show More Show Less

B4 Front Strut Assembly - Right

For vehicles with Sport suspension

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:344743

Part#: 22-234643

In Stock

$ 191.00 USD

Add to Wish List

Qty

$ 191.00 USD

Add to Wish List

Bilstein B4 OE Replacement Series gas pressure shocks and struts are specifically engineered to be the best choice for maintaining the original ride quality of your vehicle, while meeting or exceeding OE standards. These dampers are the ideal choice for the driver looking to restore the original performance and handling of their vehicle, with the added benefit of world-famous Bilstein quality.

Show More Show Less

Bilstein B6 Performance FRONT RIGHT Strut - E83 X3 2.5i, 3.0i, 3.0si ...

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:2297

Part#: VE3-B457-H1

Ships in 3 Business Days

$ 329.00 USD

Add to Wish List

Qty

$ 329.00 USD

Add to Wish List

Position: Front Right
Setting: Performance, for stock suspensions

Front Right Bilstein B6 Performance shock. Performance shocks are for cars with the standard, factory suspension. They are typically about 20% firmer than the original shock, improving body roll, brake dive, and overall handling. Includes top nut. Price is per shock.

This Bilstein B6 Performance Front shock fits the following BMWs:
2004+ E83 X3 X3 2.5i, X3 3.0i, X3 3.0si, X3 xDrive30i

Show More Show Less

Bilstein B6 Performance FRONT LEFT Strut - E83 X3 2.5i, 3.0i, 3.0si 2...

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:2296

Part#: VE3-B456-H1

Ships in 3 Business Days

$ 329.00 USD

Add to Wish List

Qty

$ 329.00 USD

Add to Wish List

Position: Front left
Setting: Performance, for stock suspensions

Front Bilstein B6 Performance shock. Performance shocks are for cars with the standard, factory suspension. They are typically about 20% firmer than the original shock, improving body roll, brake dive, and overall handling. Includes top nut. Price is per shock.

This Bilstein B6 Performance Front shock fits the following BMWs:
2004+ E83 X3 X3 2.5i, X3 3.0i, X3 3.0si, X3 xDrive30i

Show More Show Less

B4 Front Strut Assembly - Right

For vehicles with standard suspension

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:344618

Part#: 22-123619

Ships in 3 Business Days

$ 181.00 USD

Add to Wish List

Qty

$ 181.00 USD

Add to Wish List

Bilstein B4 OE Replacement Series gas pressure shocks and struts are specifically engineered to be the best choice for maintaining the original ride quality of your vehicle, while meeting or exceeding OE standards. These dampers are the ideal choice for the driver looking to restore the original performance and handling of their vehicle, with the added benefit of world-famous Bilstein quality.

Show More Show Less

Apex EC-7 19" Staggered Wheel Set - Race Silver

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms
2X Entries For Our G87 M2 Sweepstakes!

T#:599071

Part#: EC71995ET28RSKT

Ships in 5 Business Days

$ 1,876.00 USD

Add to Wish List

Qty

$ 1,876.00 USD

Add to Wish List

Specifications: Color - Race Silver Size Front - 19x9.5" ET28 Size Rear - 19x10.5" ET45

Bilstein B6 Performance Shock & Strut Set - E83 X3

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:4619

Part#: E83-X3-HD

Ships in 3 Business Days

$ 1,028.00 USD

Add to Wish List

Qty

$ 1,028.00 USD

Add to Wish List

A complete set of Bilstein Heavy Duty shocks for stock springs. Set includes 2 front struts and 2 rear shocks. The Bilstein Heavy Duty (HD) Shock is designed for use with stock springs. These shocks provide improved handling and stability without sacrificing ride comfort.

This Bilstein HD package fits the following BMWs:
2004-2010 E83 BMW X3 2.5i X3 3.0i X3 3.0si

Show More Show Less

APEX EC-7 19x10" ET25 Anthracite Wheel 23.5lbs

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms
2X Entries For Our G87 M2 Sweepstakes!

T#:201373

Part#: EC71910ET25AN

Ships in 5 Business Days

$ 469.00 USD

Add to Wish List

Qty

$ 469.00 USD

Add to Wish List

19x10" ET25 APEX EC-7 Wheel 23.5lbs.

Wheel Specs
Fitment:	Mostly Rear
Size:	19x10"
Offset (mm):	25
Weight (lbs):	23.5
Profile:	3, deep dish

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

B4 Front Strut Assembly - Left

For vehicles with standard suspension

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:344617

Part#: 22-123602

Ships on Jul 28, 2026

$ 181.00 USD

Add to Wish List

Qty

$ 181.00 USD

Add to Wish List

Bilstein B4 OE Replacement Series gas pressure shocks and struts are specifically engineered to be the best choice for maintaining the original ride quality of your vehicle, while meeting or exceeding OE standards. These dampers are the ideal choice for the driver looking to restore the original performance and handling of their vehicle, with the added benefit of world-famous Bilstein quality.

Show More Show Less

APEX EC-7 19x9.5" ET22 Satin Black Wheel 22.9lbs

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms
2X Entries For Our G87 M2 Sweepstakes!

T#:201362

Part#: EC71995ET22SMBK

Ships in 5 Business Days

$ 459.00 USD

Add to Wish List

Qty

$ 459.00 USD

Add to Wish List

19x10" ET25 APEX EC-7 Wheel 23.5lbs.

Wheel Specs
Fitment:	Mostly Rear
Size:	19x9.5"
Offset (mm):	22
Weight (lbs):	22.9
Profile:	3, deep dish

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

Bilstein B4 OE Replacement Shock and Strut Package - E83

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:384729

Part#: 19-123622KT

Ships on Jul 28, 2026

$ 580.00 USD

Add to Wish List

Qty

$ 580.00 USD

Add to Wish List

Bilstein strut/shock package for stock springs. Set includes 2 front Bilstein B4 OE Replacement struts and 2 rear Bilstein B4 OE Replacement shocks. Bilstein B4 Series gas pressure shocks and struts are specifically designed to be the economical choice for replacing the dampers on your vehicle. The B4 Series shocks and struts are rigorously engineered to meet OE standards and identically replicate the original ride quality of your vehicle. Shock dampening and rebound is set to match the original specifications from the factory to retain the same handling, stability, and ride comfort, but with the superior Bilstein quality for a long life and consistent performance in every condition. Lifetime warranty!

This item fits the following BMWs:
2003-2010 E83 BMW All models with standard suspension

Show More Show Less

E83 B4 Front Strut Assembly - Left

For vehicles with Sport suspension

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:344742

Part#: 22-234636

Ships on Jul 28, 2026

$ 191.00 USD

Add to Wish List

Qty

$ 191.00 USD

Add to Wish List

Bilstein B4 OE Replacement Series gas pressure shocks and struts are specifically engineered to be the best choice for maintaining the original ride quality of your vehicle, while meeting or exceeding OE standards. These dampers are the ideal choice for the driver looking to restore the original performance and handling of their vehicle, with the added benefit of world-famous Bilstein quality.

Show More Show Less

Bilstein B12 Pro-Kit Suspension System - E83 X3 2.5L 3.0L

For vehicles without air suspension

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:346407

Part#: 46-189547

Special Order: No Guaranteed ETA

$ 1,239.00 USD

Add to Wish List

Qty

$ 1,239.00 USD

Add to Wish List

Bilstein has teamed up with Eibach to offer matched shock and spring packages. These Eibach springs are mated to a special set of Bilstein shocks to deliver a sporty and taut ride with as little impact on ride comfort as possible.

The Pro Kit uses an Eibach Pro Kit spring with Bilstein's Sport shocks and struts. Instead of taking parts from different manufacturers, Bilstein has tested the performance of the Eibach spring and tailored their shocks to be a true match for the new spring rate and ride height. This is known as a matched shock and spring and very few tuning companies take these extra steps. Eibach springs tend to be softer overall than most other aftermarket springs, which ensures the ride stays close to a stock comfort while still giving you a lowered stance and improved handling.

Bilstein B12 Features:

Precise response and excellent driving performance
Springs and shocks road tested and fine-tuned to complement one another
Bilstein Monotube/Inverted gas pressure technology
TUV certified
Made In Germany
Average Lowering of 25 to 40mm

Most cars don't need coil overs to improve their handling and bodyroll. For most drivers, simply replacing the shocks and springs with performance versions will meet their goals. If your shocks need replacing, and you felt the handling could be improved a little bit, this is an excellent performance suspension for you.

This item fits the following BMWs:
2004-2010 E83 BMW X3 2.5L 3.0L

Show More Show Less

GSP Front Axle Assembly - Left - E83

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:389715

Part#: NCV27514

In Stock

$ 130.99

This product was last offered at the strikethrough price on
05-03-2026

$ 110.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 130.99

This product was last offered at the strikethrough price on
05-03-2026

$ 110.99 USD

Limited Qty Sale

Add to Wish List

Since established in 2004, GSP North America has positioned itself as a leading supplier of New Axles in North America.GSP’s new axle program consistently offers the best application coverage, most SKU count, and more new numbers than any other competitors. GSP’s hub assembly program was introduced to North America market in 2010 and has grown into one the most trustable programs in US market.

This item fits the following BMWs:

E83 BMW X3

Show More Show Less

E83 X3 B4 Rear Shock Absorber - Priced Each

For vehicles with standard suspension

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:344379

Part#: 19-123622

In Stock

$ 109.00 USD

Add to Wish List

Qty

$ 109.00 USD

Add to Wish List

Bilstein B4 OE Replacement Series gas pressure shocks and struts are specifically engineered to be the best choice for maintaining the original ride quality of your vehicle, while meeting or exceeding OE standards. These dampers are the ideal choice for the driver looking to restore the original performance and handling of their vehicle, with the added benefit of world-famous Bilstein quality.

Show More Show Less

APEX Solid Gloss Black BMW Center Caps - Priced Each

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms
2X Entries For Our G87 M2 Sweepstakes!

T#:639899

Part#: HW-APX-CAP-BLK

Ships in 9 Business Days

$ 9.99 USD

Add to Wish List

Qty

$ 9.99 USD

Add to Wish List

APEX Wheels Metal Valve Stem - Anthracite - BMW & MINI

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms
2X Entries For Our G87 M2 Sweepstakes!

T#:593645

Part#: HW-OEM-VALVE-GM

Ships in 2 Business Days

$ 15.00 USD

Add to Wish List

Qty

$ 15.00 USD

Add to Wish List

APEX Wheels metal valve stems come in 3 colors that compliment wheels in any finish. Made in Germany, they are guaranteed to fit OEM Huf/Beru TPMS sensors and can also be installed without them. Valve stems are sold individually Made in Germany Guaranteed to fit APEX wheels, and also work with a variety of OEM and aftermarket wheels Guaranteed to fit OEM Huf/Beru TPMS sensors Not compatible with VDO TPMS sensors Work without the use of TPMS sensors Available in Silver, Anthracite, and Black Black and Anthracite valve stems come with a color-matched knurled, metal cap Silver valve stems comes with a knurled color-matched plastic cap

Show More Show Less

APEX EC-7 19x10.5" ET22 Satin Black Wheel 23.9lbs

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms
2X Entries For Our G87 M2 Sweepstakes!

T#:201374

Part#: EC719105ET22SMBK

Ships in 5 Business Days

$ 479.00 USD

Add to Wish List

Qty

$ 479.00 USD

Add to Wish List

19x10.5" ET22 APEX EC-7 Wheel 23.9lbs.

Wheel Specs
Fitment:	Front or Rear
Size:	19x10.5"
Offset (mm):	22
Weight (lbs):	23.9
Profile:	3, deep dish

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX EC-7 19x9.5" ET22 Anthracite Wheel 22.9lbs

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms
2X Entries For Our G87 M2 Sweepstakes!

T#:201364

Part#: EC71995ET22AN

Ships in 5 Business Days

$ 459.00 USD

Add to Wish List

Qty

$ 459.00 USD

Add to Wish List

19x10" ET25 APEX EC-7 Wheel 23.5lbs.

Wheel Specs
Fitment:	Mostly Rear
Size:	19x9.5"
Offset (mm):	22
Weight (lbs):	22.9
Profile:	3, deep dish

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX EC-7 19x10.5" ET22 Anthracite Wheel 23.9lbs

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms
2X Entries For Our G87 M2 Sweepstakes!

T#:201376

Part#: EC719105ET22AN

Ships in 5 Business Days

$ 479.00 USD

Add to Wish List

Qty

$ 479.00 USD

Add to Wish List

19x10.5" ET22 APEX EC-7 Wheel 23.9lbs.

Wheel Specs
Fitment:	Front or Rear
Size:	19x10.5"
Offset (mm):	22
Weight (lbs):	23.9
Profile:	3, deep dish

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX Wheels Metal Valve Stem - Black - BMW & MINI

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms
2X Entries For Our G87 M2 Sweepstakes!

T#:593644

Part#: HW-OEM-VALVE-BK

Ships in 2 Business Days

$ 15.00 USD

Add to Wish List

Qty

$ 15.00 USD

Add to Wish List

APEX Wheels metal valve stems come in 3 colors that compliment wheels in any finish. Made in Germany, they are guaranteed to fit OEM Huf/Beru TPMS sensors and can also be installed without them. Valve stems are sold individually Made in Germany Guaranteed to fit APEX wheels, and also work with a variety of OEM and aftermarket wheels Guaranteed to fit OEM Huf/Beru TPMS sensors Not compatible with VDO TPMS sensors Work without the use of TPMS sensors Available in Silver, Anthracite, and Black Black and Anthracite valve stems come with a color-matched knurled, metal cap Silver valve stems comes with a knurled color-matched plastic cap

Show More Show Less

APEX EC-7 19x10" ET25 Satin Black Wheel 23.5lbs

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms
2X Entries For Our G87 M2 Sweepstakes!

T#:201371

Part#: EC71910ET25SMBK

Ships in 5 Business Days

$ 469.00 USD

Add to Wish List

Qty

$ 469.00 USD

Add to Wish List

19x10" ET25 APEX EC-7 Wheel 23.5lbs.

Wheel Specs
Fitment:	Mostly Rear
Size:	19x10"
Offset (mm):	25
Weight (lbs):	23.5
Profile:	3, deep dish

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX Wheels Metal Valve Stem - Silver - BMW & MINI

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms
2X Entries For Our G87 M2 Sweepstakes!

T#:593646

Part#: HW-OEM-VALVE-SV

Ships in 2 Business Days

$ 17.00 USD

Add to Wish List

Qty

$ 17.00 USD

Add to Wish List

APEX Wheels metal valve stems come in 3 colors that compliment wheels in any finish. Made in Germany, they are guaranteed to fit OEM Huf/Beru TPMS sensors and can also be installed without them. Valve stems are sold individually Made in Germany Guaranteed to fit APEX wheels, and also work with a variety of OEM and aftermarket wheels Guaranteed to fit OEM Huf/Beru TPMS sensors Not compatible with VDO TPMS sensors Work without the use of TPMS sensors Available in Silver, Anthracite, and Black Black and Anthracite valve stems come with a color-matched knurled, metal cap Silver valve stems comes with a knurled color-matched plastic cap

Show More Show Less

APEX ARC-8 19x9.5" ET33 Satin Black Wheel 20.5lbs

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms
2X Entries For Our G87 M2 Sweepstakes!

T#:201383

Part#: ARC81995ET33SMBK

Ships in 5 Business Days

$ 449.00 USD

Add to Wish List

Qty

$ 449.00 USD

Add to Wish List

19x9.5" ET33 APEX ARC-8 Wheel 20.5lbs.

Wheel Specs
Fitment:	Front or Rear
Size:	19x9.5"
Offset (mm):	33
Weight (lbs):	20.5
Profile:	Concave

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX EC-7 19x9.5" ET43 Silver Wheel 23lbs

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms
2X Entries For Our G87 M2 Sweepstakes!

T#:201357

Part#: EC71995ET43RS

Ships in 5 Business Days

$ 426.00 USD

Add to Wish List

Qty

$ 426.00 USD

Add to Wish List

19x9.5" ET43 APEX EC-7 Wheel 23lbs.

Wheel Specs
Fitment:	Mostly Rear
Size:	19x9.5"
Offset (mm):	43
Weight (lbs):	23
Profile:	2, moderate dish

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

Bilstein B4 OE Replacement Shock and Strut Package - E83

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:384730

Part#: 19-234656KT

Ships on Jul 28, 2026

$ 606.00 USD

Add to Wish List

Qty

$ 606.00 USD

Add to Wish List

Bilstein strut/shock package for stock springs. Set includes 2 front Bilstein B4 OE Replacement struts and 2 rear Bilstein B4 OE Replacement shocks. Bilstein B4 Series gas pressure shocks and struts are specifically designed to be the economical choice for replacing the dampers on your vehicle. The B4 Series shocks and struts are rigorously engineered to meet OE standards and identically replicate the original ride quality of your vehicle. Shock dampening and rebound is set to match the original specifications from the factory to retain the same handling, stability, and ride comfort, but with the superior Bilstein quality for a long life and consistent performance in every condition. Lifetime warranty!

This item fits the following BMWs:
2003-2010 E83 BMW All models with Sport Suspension

Show More Show Less

APEX EC-7 19x9.5" ET33 Anthracite Wheel 22.5lbs

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms
2X Entries For Our G87 M2 Sweepstakes!

T#:201361

Part#: EC71995ET33AN

Back Ordered

$ 459.00 USD

Add to Wish List

Qty

$ 459.00 USD

Add to Wish List

19x9.5" ET33 APEX EC-7 Wheel 23.5lbs.

Wheel Specs
Fitment:	Front or Rear
Size:	19x9.5"
Offset (mm):	33
Weight (lbs):	22.5
Profile:	3, deep dish

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX EC-7 19x9.5" ET33 Satin Black Wheel 22.5lbs

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms
2X Entries For Our G87 M2 Sweepstakes!

T#:201359

Part#: EC71995ET33SMBK

Ships in 5 Business Days

$ 459.00 USD

Add to Wish List

Qty

$ 459.00 USD

Add to Wish List

19x9.5" ET33 APEX EC-7 Wheel 23.5lbs.

Wheel Specs
Fitment:	Front or Rear
Size:	19x9.5"
Offset (mm):	33
Weight (lbs):	22.5
Profile:	3, deep dish

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX EC-7 19x9.5" ET33 Silver Wheel 22.5lbs

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms
2X Entries For Our G87 M2 Sweepstakes!

T#:201360

Part#: EC71995ET33RS

Ships in 5 Business Days

$ 459.00 USD

Add to Wish List

Qty

$ 459.00 USD

Add to Wish List

19x9.5" ET33 APEX EC-7 Wheel 23.5lbs.

Wheel Specs
Fitment:	Front or Rear
Size:	19x9.5"
Offset (mm):	33
Weight (lbs):	22.5
Profile:	3, deep dish

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

Project Cars

SELECT YOUR BMW

Sub-Categories

Select Vehicle

Purpose

Category

Brand

Price

Shipping

Narrow Results