BMW Z3 (1996-2002)

Clear BMW chassis

Please ensure your correct model is selected

Sub-Categories

Sort By:
KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E36, E39 (not M5), E46 (not M3), E60, E82 (not 1M), E9X (not M3), Z3, MZ3, Z4
KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E36, E39 ...
KMAC - Corporate Logo
T#:389645
Part#: 192416-1J
In Stock
$ 380.00 USD
Free Shipping
Add to Wish List
$ 380.00 USD
Free Shipping
Add to Wish List
Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012  E82 BMW  128i 135i
6/1992-1999  E36 BMW  318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005  E46 BMW  323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011  E90 BMW  325i 328i 330i 335d 335i - Sedan
2006-2012  E91 BMW  328i - Wagon
2007-2013  E92 BMW  328i 335i 335is - Coupe
2007-2013  E93 BMW  328i 335i - Convertible
1997-2003  E39 BMW  525i 528i 530i 540i (not for cars with EDC)
2004-2010  E60 BMW  525i 530i 528i 535i 545i 550i
2004-2011  E63 E64 BMW  645ci 650i
1997-2002  Z3 BMW  Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008  E85 BMW  Z4 2.5i Z4 3.0i Z4 3.0si
2009+  Z4 BMW  Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003  E52 BMW  Z8 Roadster (without EDC)
Show More Show Less
BMC Performance Air Filter - E36, E46, E39, E38, E83, E85, E86
BMC Performance Air Filter - E36, E46, E39, E38, E83, E85, E86 ...
BMC - Corporate Logo
T#:397411
Part#: FB132/01
In Stock at Vendor
$ 84.99 USD
Free Shipping
Add to Wish List
$ 84.99 USD
Free Shipping
Add to Wish List
Looking to upgrade your air filter for increased flow and performance? BMC filter allow significantly higher air flow and are perfectly molded in one piece to fit exactly the same as your stock air filter. These filters are constructed from multi-layerd cotton gauze that is pre-oiled and can be cleaned and regenerated using the BMC regeneration kit.
Show More Show Less
Black Forest Industries Billet Heavy Weight Shift Knob - Alcantara Or Leather
Black Forest Industries Billet Heavy Weight Shift Knob - Alcantara Or...
Black Forest Industries - Corporate Logo
T#:391722
Part#: GS2B
In Stock
Starting at $ 184.99 USD
Free Shipping
Add to Wish List
Starting at $ 184.99 USD
Free Shipping
Add to Wish List

This weighted shift knob makes shifts faster and the extra-large globe shape encourages over-palm shifting. The Black Forest Industries Billet Knob weighs in at 8.8oz (250g), about twice as much as a stock knob and a little heaver than the BMW ZHP knob. The heavier knob amplifies the pendulum motion of the shift lever resulting in smoother and faster shift times. BFI has designed this knob for BMW and VW fitments to fit snug on the shift lever and be secured with Allen set screws. They were careful to reduce tolerances compared to universal knobs. The overall height of the BFI knob is the same as stock anatomic knobs (some BMW M/Performance models have a stock knob that is shorter than this one).

Included with the BFI Billet knob is a matching BFI crest shift emblem. A 5 or 6-speed pattern emblem is available separately.

Choose from soft alcantara or perforated air leather with either a silver or black anodized base.

Show More Show Less
BFI GS2 Automatic Shift Knob - Black w/ Black Perforated Air Leather - E36 Z3 E46 E39 E38 E53 E60 (Automatic Trans)
BFI GS2 Automatic Shift Knob - Black w/ Black Perforated Air Leather ...
Black Forest Industries - Corporate Logo
T#:4813275
Part#: GS2-BMA-1S
Ships on Aug 12, 2026
$ 224.99 USD
Free Shipping
Add to Wish List
$ 224.99 USD
Free Shipping
Add to Wish List
Introducing the world's first Black Forest Industries shift knob specifically for Automatic transmission BMW applications. Built with the same quality materials as our other GS2 shift knobs, this application adds a control lever and internal springs to operate the automatic mechanism of a BMW shift lever.
Show More Show Less
BFI GS2 Automatic Shift Knob - Black w/ Gray Alcantara - E36 Z3 E46 E39 E38 E53 E60 (Automatic Trans)
BFI GS2 Automatic Shift Knob - Black w/ Gray Alcantara - E36 Z3 E46 E...
Black Forest Industries - Corporate Logo
T#:4813277
Part#: GS2-BMA-1SUF
Ships on Aug 12, 2026
$ 229.99 USD
Free Shipping
Add to Wish List
$ 229.99 USD
Free Shipping
Add to Wish List
Introducing the world's first Black Forest Industries shift knob specifically for Automatic transmission BMW applications. Built with the same quality materials as our other GS2 shift knobs, this application adds a control lever and internal springs to operate the automatic mechanism of a BMW shift lever.
Show More Show Less
BFI GS2 Automatic Shift Knob - Black w/ Black Alcantara - E36 Z3 E46 E39 E38 E53 E60 (Automatic Trans)
BFI GS2 Automatic Shift Knob - Black w/ Black Alcantara - E36 Z3 E46 ...
Black Forest Industries - Corporate Logo
T#:4813276
Part#: GS2-BMA-1SU
Ships on Aug 12, 2026
$ 229.99 USD
Free Shipping
Add to Wish List
$ 229.99 USD
Free Shipping
Add to Wish List
Introducing the world's first Black Forest Industries shift knob specifically for Automatic transmission BMW applications. Built with the same quality materials as our other GS2 shift knobs, this application adds a control lever and internal springs to operate the automatic mechanism of a BMW shift lever.
Show More Show Less
BFI GS2 Automatic Shift Knob - Silver w/ Black Perforated Air Leather - E36 Z3 E46 E39 E38 E53 E60 (Automatic Trans)
BFI GS2 Automatic Shift Knob - Silver w/ Black Perforated Air Leather...
Black Forest Industries - Corporate Logo
T#:4813272
Part#: GS2-BMA-1
Ships on Aug 12, 2026
$ 219.99 USD
Free Shipping
Add to Wish List
$ 219.99 USD
Free Shipping
Add to Wish List
Introducing the world's first Black Forest Industries shift knob specifically for Automatic transmission BMW applications. Built with the same quality materials as our other GS2 shift knobs, this application adds a control lever and internal springs to operate the automatic mechanism of a BMW shift lever.
Show More Show Less
Adjustable Rear Camber/Toe Bushings
Adjustable Rear Camber/Toe Bushings
KMAC - Corporate Logo
T#:582353
Part#: 192026G
In Stock
$ 320.00 USD
Free Shipping
Add to Wish List
$ 320.00 USD
Free Shipping
Add to Wish List
KMAC Stage 2 Street/Track Front Adjustable Camber/Caster Plates - E36, E39 (not M5), E46 (not M3), E60, E82 (not 1M), E9X (not M3), Z3, MZ3, Z4
KMAC Stage 2 Street/Track Front Adjustable Camber/Caster Plates - E36...
KMAC - Corporate Logo
T#:389647
Part#: 192416-2L
Special Order: No Guaranteed ETA
$ 545.00 USD
Free Shipping
Add to Wish List
$ 545.00 USD
Free Shipping
Add to Wish List
Location: Front
Type: Street/Track, Stage 2
Bearings: main PTFE-lined pillow-ball bearing suspended in polyurethane; self-lubricating radial axial bearing/bushing in upper spring plate
Springs: includes OEM size upper spring perch, 60mm upper spring perch, and 2.5" upper spring perch

The Stage 2 KMAC plates are a mixed track and street camber/caster plate meant to be used in a variety of suspensions and setups. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions and upper spring perches are included for OEM springs, 60mm, and 2.5" coil over springs. The upper perch assembly incorporate a self-sliding radial bushing that allows the spring to spin during its travel instead of bind. This reduces tension on the spring and helps reduce noise and spring 'popping' noises. Bearing inserts, spacers for correct articulating angles, and 3 sizes of upper nut adapters included. The urethane bushings and bearings are replaceable if they wear out. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Basic instructions included but professional installation is required.

Note: suspensions vary from manufacturer to manufacturer. The proper stacked height and clearances are required. K-Mac includes bearing adapters, spacers, and various top nuts but it is still the responsibility of the installer to ensure a correct and safe fitment. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012  E82 BMW  128i 135i
6/1992-1999  E36 BMW  318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005  E46 BMW  323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011  E90 BMW  325i 328i 330i 335d 335i - Sedan
2006-2012  E91 BMW  328i - Wagon
2007-2013  E92 BMW  328i 335i 335is - Coupe
2007-2013  E93 BMW  328i 335i - Convertible
1997-2003  E39 BMW  525i 528i 530i 540i (not for cars with EDC)
2004-2010  E60 BMW  525i 530i 528i 535i 545i 550i
2004-2011  E63 E64 BMW  645ci 650i
1997-2002  Z3 BMW  Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008  E85 BMW  Z4 2.5i Z4 3.0i Z4 3.0si
2009+  Z4 BMW  Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003  E52 BMW  Z8 Roadster (without EDC)
Show More Show Less
KMAC Stage 3 Street/Track Front Adjustable Camber/Caster Plates - E36, E39 (not M5), E46 (not M3), E60, E82 (not 1M), E9X (not M3), Z3, MZ3, Z4
KMAC Stage 3 Street/Track Front Adjustable Camber/Caster Plates - E36...
KMAC - Corporate Logo
T#:389646
Part#: 192416-3L
Special Order: No Guaranteed ETA
$ 545.00 USD
Free Shipping
Add to Wish List
$ 545.00 USD
Free Shipping
Add to Wish List
Location: Front
Type: Street/Track, Stage 2
Bearings: main PTFE-lined pillow-ball bearing suspended in polyurethane; self-lubricating radial axial bearing/bushing in upper spring plate
Springs: includes OEM size upper spring perch, 60mm upper spring perch, and 2.5" upper spring perch

The Stage 3 KMAC plates are a mixed track and street camber/caster plate meant to be used in a variety of suspensions and setups. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions and upper spring perches are included for OEM springs, 60mm, and 2.5" coil over springs. The upper perch assembly incorporate a self-sliding radial bushing that allows the spring to spin during its travel instead of bind. This reduces tension on the spring and helps reduce noise and spring 'popping' noises. Bearing inserts, spacers for correct articulating angles, and 3 sizes of upper nut adapters included. The urethane bushings and bearings are replaceable if they wear out. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Basic instructions included but professional installation is required.

Note: suspensions vary from manufacturer to manufacturer. The proper stacked height and clearances are required. K-Mac includes bearing adapters, spacers, and various top nuts but it is still the responsibility of the installer to ensure a correct and safe fitment. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012  E82 BMW  128i 135i
6/1992-1999  E36 BMW  318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005  E46 BMW  323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011  E90 BMW  325i 328i 330i 335d 335i - Sedan
2006-2012  E91 BMW  328i - Wagon
2007-2013  E92 BMW  328i 335i 335is - Coupe
2007-2013  E93 BMW  328i 335i - Convertible
1997-2003  E39 BMW  525i 528i 530i 540i (not for cars with EDC)
2004-2010  E60 BMW  525i 530i 528i 535i 545i 550i
2004-2011  E63 E64 BMW  645ci 650i
1997-2002  Z3 BMW  Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008  E85 BMW  Z4 2.5i Z4 3.0i Z4 3.0si
2009+  Z4 BMW  Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003  E52 BMW  Z8 Roadster (without EDC)
Show More Show Less
BFI GS2 Automatic Shift Knob - Black w/ Rosso Centaurus (Red) Perforated Leather - E36 Z3 E46 E39 E38 E53 E60 (Automatic Trans)
BFI GS2 Automatic Shift Knob - Black w/ Rosso Centaurus (Red) Perfora...
Black Forest Industries - Corporate Logo
T#:4813279
Part#: GS2-BMA-1SRC
Back Ordered
$ 224.99 USD
Free Shipping
Add to Wish List
$ 224.99 USD
Free Shipping
Add to Wish List
Introducing the world's first Black Forest Industries shift knob specifically for Automatic transmission BMW applications. Built with the same quality materials as our other GS2 shift knobs, this application adds a control lever and internal springs to operate the automatic mechanism of a BMW shift lever.
Show More Show Less
APR Valve Stem Caps - Set Of 4 - Gunmetal
APR Valve Stem Caps - Set Of 4 - Gunmetal
Call In Or Chat For Best Price!
APR - Corporate Logo
T#:31092523
Part#: MS100179
In Stock
11% off MSRP $ 17.94

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 15.95 USD
Free Shipping
Add to Wish List
11% off MSRP
$ 17.94

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 15.95 USD
Free Shipping
Add to Wish List

APR Valve Stem Caps - Set Of 4 - Gunmetal offer a stylish and functional upgrade for any vehicle. These high-quality aluminum valve stem caps come in a sleek gunmetal finish and feature an engraved APR logo, which adds a touch of sophistication to your wheels.

  • Material: Made from durable aluminum for long-lasting performance
  • Design: Engraved APR logo adds a distinctive look
  • Finish: Gunmetal color enhances the visual appeal of your wheels
  • Set Includes: 4 valve stem caps for a complete upgrade
  • Compatibility: Fits most standard valve stems

These APR Valve Stem Caps are designed to provide both aesthetics and durability, making them a great choice for enhancing your vehicle's style.

Show More Show Less
APR Valve Stem Caps - Set Of 4 - Silver
APR Valve Stem Caps - Set Of 4 - Silver
Call In Or Chat For Best Price!
APR - Corporate Logo
T#:31125602
Part#: MS100178
In Stock
11% off MSRP $ 17.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 15.99 USD
Free Shipping
Add to Wish List
11% off MSRP
$ 17.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 15.99 USD
Free Shipping
Add to Wish List

APR Valve Stem Caps - Set Of 4 - Silver are a stylish and functional upgrade for any vehicle. This set includes four high-quality aluminum valve stem caps, each engraved with the distinctive APR logo. These caps are designed to enhance the appearance of your wheels while providing durability and reliability.

  • Stylish Appearance: Each cap features a sleek silver finish and an engraved APR logo, adding a touch of elegance to your vehicle.
  • Durable Construction: Made from high-quality aluminum, these valve stem caps are built to withstand harsh conditions and resist corrosion.
  • Easy Installation: Simple to install and compatible with most standard valve stems.
  • Enhanced Wheel Aesthetics: Upgrades the look of your wheels with a subtle yet impactful design.
  • Functional Protection: Helps protect valve stems from dirt and moisture, ensuring consistent performance.

This set of valve stem caps is an excellent choice for anyone looking to add a refined touch to their vehicle's wheels.

Show More Show Less
BFI GS2 Automatic Shift Knob - Silver w/ Gray Alcantara - E36 Z3 E46 E39 E38 E53 E60 (Automatic Trans)
BFI GS2 Automatic Shift Knob - Silver w/ Gray Alcantara - E36 Z3 E46 ...
Black Forest Industries - Corporate Logo
T#:4813274
Part#: GS2-BMA-1UF
Ships on Aug 12, 2026
$ 224.99 USD
Free Shipping
Add to Wish List
$ 224.99 USD
Free Shipping
Add to Wish List
Introducing the world's first Black Forest Industries shift knob specifically for Automatic transmission BMW applications. Built with the same quality materials as our other GS2 shift knobs, this application adds a control lever and internal springs to operate the automatic mechanism of a BMW shift lever.
Show More Show Less
BFI GS2 Automatic Shift Knob - Silver w/ Rosso Centaurus (Red) Perforated Leather - E36 Z3 E46 E39 E38 E53 E60 (Automatic Trans)
BFI GS2 Automatic Shift Knob - Silver w/ Rosso Centaurus (Red) Perfor...
Black Forest Industries - Corporate Logo
T#:4813281
Part#: GS2-BMA-1RC
Ships on Aug 12, 2026
$ 219.99 USD
Free Shipping
Add to Wish List
$ 219.99 USD
Free Shipping
Add to Wish List
Introducing the world's first Black Forest Industries shift knob specifically for Automatic transmission BMW applications. Built with the same quality materials as our other GS2 shift knobs, this application adds a control lever and internal springs to operate the automatic mechanism of a BMW shift lever.
Show More Show Less
BFI GS2 Automatic Shift Knob - Black w/ Red Alcantara - E36 Z3 E46 E39 E38 E53 E60 (Automatic Trans)
BFI GS2 Automatic Shift Knob - Black w/ Red Alcantara - E36 Z3 E46 E3...
Black Forest Industries - Corporate Logo
T#:4813278
Part#: GS2-BMA-1SRU
Ships on Aug 12, 2026
$ 229.99 USD
Free Shipping
Add to Wish List
$ 229.99 USD
Free Shipping
Add to Wish List
Introducing the world's first Black Forest Industries shift knob specifically for Automatic transmission BMW applications. Built with the same quality materials as our other GS2 shift knobs, this application adds a control lever and internal springs to operate the automatic mechanism of a BMW shift lever.
Show More Show Less
BFI GS2 Automatic Shift Knob - Silver w/ Black Alcantara - E36 Z3 E46 E39 E38 E53 E60 (Automatic Trans)
BFI GS2 Automatic Shift Knob - Silver w/ Black Alcantara - E36 Z3 E46...
Black Forest Industries - Corporate Logo
T#:4813273
Part#: GS2-BMA-1U
Ships on Aug 12, 2026
$ 224.99 USD
Free Shipping
Add to Wish List
$ 224.99 USD
Free Shipping
Add to Wish List
Introducing the world's first Black Forest Industries shift knob specifically for Automatic transmission BMW applications. Built with the same quality materials as our other GS2 shift knobs, this application adds a control lever and internal springs to operate the automatic mechanism of a BMW shift lever.
Show More Show Less
BFI GS2 Automatic Shift Knob - Silver w/ Red Alcantara - E36 Z3 E46 E39 E38 E53 E60 (Automatic Trans)
BFI GS2 Automatic Shift Knob - Silver w/ Red Alcantara - E36 Z3 E46 E...
Black Forest Industries - Corporate Logo
T#:4813280
Part#: GS2-BMA-1RU
Ships on Aug 12, 2026
$ 224.99 USD
Free Shipping
Add to Wish List
$ 224.99 USD
Free Shipping
Add to Wish List
Introducing the world's first Black Forest Industries shift knob specifically for Automatic transmission BMW applications. Built with the same quality materials as our other GS2 shift knobs, this application adds a control lever and internal springs to operate the automatic mechanism of a BMW shift lever.
Show More Show Less
Seatbelt 6-point Race Harness Receptacles - Macht Schnell
Seatbelt 6-point Race Harness Receptacles - Macht Schnell
Macht Schnell - Corporate Logo
T#:338507
Part#: 79.20.150K
Ships on Aug 17, 2026
Starting at $ 174.00 USD
Free Shipping
Add to Wish List
Starting at $ 174.00 USD
Free Shipping
Add to Wish List
Many racing series and event organizers are requiring 5 or 6-point harnesses in their events now. Attaching the anchor points to the seat base is a desired alternative to drilling holes in your floor and carpet*. This set includes the 6-point anchor to attach to the Macht Schnell floor mount as well as side attachments for either a bolt-in or snap-in harness.

* - note that most racing harness manufacturers will advise that drilling through the floor is the best method for mounting harnesses. This allows you to locate the mount in the ideal location and angle to fit your driving position. The proper installation is paramount to ensure the harness works correctly in an impact.

Sold per seat.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i 1M Coupe
1992-1998 E36 BMW 318i 318is 318ti 323is 325i 325is 328i 328is M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3 (not convertibles)
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive M3 - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive M3 - Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe
Show More Show Less

Select Vehicle

BMW Mini
Clear Vehicle

Purpose

Category

Brand

Price

$
$

Shipping