CCV/PCV Breather Hoses for BMW Z3 (1996-2002)

The factory rubber/plastic hoses become brittle and crack over time. Brittle and cracked hoses can cause multiple vacuum leaks that are impossible to repair without hose replacement. Vacuum leaks can cause many problems including rough running, missing, stalling at idle, and even a no-start condition.

The factory hoses offered through BMW are plastic and will yield the same results of becoming brittle and damaged over time. Our solution is a premium replacement that will outlast everyone of the OEM replacements. Our Silicone Crankcase Vent Hose can be used to replace the factory brittle hose to ensure your S54 is free from vacuum leaks and performing properly.

CSL Vent Hose (11157833649) - Silicone Crankcase Vent hose is a direct replacement

Key benefits:

Lifetime replacement of the brittle OEM plastic crankcase breather hose that is susceptible to cracking overtime from constant heat cycling

Design:

Retains OEM hose end fittings to ensure proper seal

“Black” 3 ply reinforced silicone w/ “White” Turner logo

Due to weak plastic construction, the factory plastic crankcase ventilation breather hose is known to fail. After years of exposure to piping-hot engine bay temperatures and chemical-laden oil vapors, the corrugated plastic tubing can crack, crumble, or fail altogether.

We set out to bulletproof your M52/S52 CCV system with a durable silicone breather hose, designed to provide a comprehensive upgrade and permanent replacement for the factory plastic hose. By replacing the flimsy, heat-hardened OEM plastic hose with a four-ply fluorosilicone hose, you'll experience peace of mind knowing your M52 or S52 is free from the inevitable return of oil leaks, vacuum leaks, and drivability concerns that would have been.

This breather hose is found at the front of the engine, and is used to connect the cyclone separator to the valve cover. It replaces OEM part number 11151703775.

Features:

Silicone construction ensures a durable replacement that is sure to outlast OE plastic Designed as a direct replacement for the factory breather hose - not too short like many aftermarket alternatives, and does not require cutting to fit Works seamlessly with the OEM OBDII valve cover and cyclone separator, as well as the Turner Motorsport Billet Aluminum Valve Cover (T#26238386) Design:

Three-ply wire-reinforced fluorosilicone hose is designed to resist degradation due to exposure to oil vapors O-rings are pre-installed in OE Norma connectors for a lasting seal Includes pre-installed 430 stainless steel hose clamps for durability and corrosion-resistance Product Development:

Our Silicone CCV Hose Upgrade was designed, engineered, tested, and quality inspected by our Research and Development team in our Wadsworth, Ohio, facility. We strive for the highest level of precision and quality through leading-edge product development technology, including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modelling, rapid prototyping utilizing our in-house 3D printer, and rigorous long-term product testing.

A combination of billet fittings and AN lines for an upgraded and serviceable crankcase vent hose. Attaches between the oil separator and the CSL air box.

The factory rubber/plastic hoses become brittle and crack over time. Brittle and cracked hoses can cause multiple vacuum leaks that are impossible to repair without hose replacement. Vacuum leaks can cause many problems including rough running, missing, stalling at idle, and even a no-start condition. The factory hoses offered by BMW are plastic and will yield the same results of becoming brittle and damaged over time.

We have created a full motorsport-style solution with our CSL Crankcase made from machined 6061 billet aluminum with AN-style fittings and nylon fiber braided lines. This is a fully serviceable replacement that will outlast every one of the OEM replacements. Our AN crankcase line can be used to replace the factory brittle hose to ensure your S54 is free from vacuum leaks and performing properly.

OEM CSL Vent Hose (11157833649) - Direct Replacement for cars with secondary shut-off valve. (11157834056)

Key benefits:

Lifetime replacement of the brittle OEM plastic crankcase breather hose
Fully Serviceable
Motorsport Aesthetic to compliment your CSL Intake Plenum
Design:

Fittings are made from billet 6061-T6 aluminum and finished in Type II black anodizing
Pre-anodized machined Turner branding
Nylon fiber braided lines
Fittings are a direct replacement for the plastic OEM fittings
Not for sale or use in the state of California on any pollution-controlled vehicle as per the California Air Resources Board.

On M52/S52-equipped BMWs, the factory crankcase ventilation (CCV) system is a notorious weak link. Between brittle plastic corrugated hoses that crumble from heat soak and an internal cyclone diaphragm prone to tearing, a failing CCV leads to massive oil consumption, vacuum leaks, and that dreaded "howling" whistle.

This kit addresses these issues with all new components and hardware. Both oil separator hoses, the cyclone separator itself, the mounting grommet, and the retaining bolts are included. Servicing this system is guaranteed to restore performance lost as a result of worn CCV components.

Kit includes:

Cyclone Separator/Crankcase Pressure Regulator Valve High Performance Silicone Breather Hose Return Hose Mounting Grommet Hex Bolt (3)

Part of the vacuum and emissions system that runs from the intake manifold back to the connecting hose.
When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

Fits the following BMW's:
E46 M52 (from 01/2000) and M54
E39 M52 (from 01/2000) and M54
E53 M54
E60 M54
E83 M54
Z3 M52 (up to 01/2000 for 2.3L and from 01/2000 for 2.8L) and M54
Z4 M54

This is the BMW crankcase return line that goes from the intake manifold to the top CCV connecting hose. We also offer a complete CCV repair kit
Since the late 1800’s Febi has been fabricating replacement metal parts. This history is self evident in the quality and vast amount of applications they service. With more than 34,000 repair solutions for cars and commercial vehicles you can be sure Febi has you covered.

This item fits the following BMWs:
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
1997-2003 E39 BMW 525i 528i 530i
2004-2010 E60 BMW 525i 530i
2004-2005 E83 BMW X3 2.5i X3 3.0i X3 3.0si
2000-2006 E53 BMW X5 3.0i
1/2000-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i
2003-2005 E85 BMW Z4 2.5i Z4 3.0i

Crankcase Vent Hose ABV0329 is an essential component designed for BMW engines, ensuring optimal performance of the crankcase ventilation system. This high-quality vent hose plays a critical role in regulating and redirecting excess gases from the crankcase back into the engine's intake, reducing harmful emissions and preventing pressure buildup. Crankcase Vent Hose ABV0329 helps maintain engine efficiency and protects against potential damage caused by over-pressurization or oil leaks.

Made from durable, heat-resistant materials, this hose is built to withstand the high temperatures and pressures common in BMW engines. It is a direct-fit replacement, making installation simple and efficient for both professionals and DIY mechanics. Available from Turner Motorsport, Crankcase Vent Hose ABV0329 is the perfect solution for restoring and maintaining your BMW’s crankcase ventilation system.

Key Benefits:

• Ensures proper crankcase ventilation for optimal engine performance
• Reduces harmful emissions by redirecting excess gases into the intake
• Prevents pressure buildup and protects against oil leaks
• Constructed from durable, heat-resistant materials for long-lasting reliability
• Direct-fit replacement, ensuring easy installation for various BMW models
• Available from Turner Motorsport, a trusted source for BMW performance parts

This tube runs from the oil separator to the lower dipstick tube.

BMW has an ongoing issue with oil separators freezing in cold weather if driving is done before the vehicle is fully warmed up. There is often a howling noise followed by numerous oil leaks. The crankcase breather valve is used to purge the oil vapor from the engine block into the valve cover. However, sometimes condensation can cause it to freeze, causing the entire oil separator system to fail, crack, and disintegrate.

Replace this and all the other components of the oil separator system to prevent damage to all the aspects of your engine. As long as you have everything off, you can rest assured that new parts will last and be reliable.