Select Vehicle
BMW
Mini
Purpose
Category
- Electrical System
Create an account to be able to build Wish Lists.
Please ensure your correct model is selected
This product was last offered at the strikethrough price on
06-14-2026
This product was last offered at the strikethrough price on
06-14-2026
This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
The TMS Water Temp Sensor Wiring Adaptor is needed when you are upgrading to OBD-I (1992-1995 components) on a 3.2 or 2.8 liter engine. These earlier engines use two separate water temp sensors in the head, one for the ECU and one for the instrument cluster. Most of the 3.2 and some of the 2.8 liter engines do not have two holes drilled in the head for the early water temp sensors. This is due to the fact that the 3.2 and 2.8 engines used a combined water temp sensor. So we designed a easy to use plug and play wiring harness. The benefits are: No cutting and splicing, no trying to fine plugs and pins. We also suggest using TMS "3.2 in a 3.0" Coolant Hose Adapter P/N: TEN9931007 to make your life easier.
This product was last offered at the strikethrough price on
06-13-2026
This product was last offered at the strikethrough price on
06-13-2026
All vehicles will lose some degree of performance due to heat soak under the right operating conditions. Engine management systems constantly monitor operating conditions and modifying parameters based on sensor inputs. BMW integrated the intake air temp sensor in the MAF housing on models such as the E39 M5, and, being sandwiched behind a hot radiator and in some applications next to an even hotter valve cover, this is less than ideal for performance applications. Absorbing excess heat from its surroundings, the MAF can’t shed it fast enough, and the ECU reads an inaccurately high intake air temperature. Compensating for this false hot air measurement, the ECU pulls timing and runs a richer fuel mixture, resulting in a significant loss of torque.
What can you do? Locate an intake air temp sensor in a location where it can properly measure incoming air temps and where it's less prone to heat soak. Mounting the sensor further away from the heat source and isolating it from the MAF housing, it can both resist the effects of heat soak longer and respond to temperature changes more quickly. The result is you’ll experience reduced torque loss and more consistent power output when you’re pushing your engine hard.
The Turner engineering team was initially skeptical of the claimed performance benefits of this modification. They first set out validate the functionality and performance benefit of a temp sensor relocation. Replicating stop-and-go traffic heat soak in a 2001 540i was a simple task in a controlled environment - their dynometer. First the car was heat soaked to simulate being stuck in traffic or moving at low speeds by running the car four times on the dyno with the dyno's cooling fans disabled. The fans were then turned on for three more runs to observe the recovery rate once air flow was reintroduced. The test: following this procedure once with a stock IAT, and once with their relocation kit in place.
The result? Turner recovered 11lb-ft torque at 2500rpm through use of their relocation kit, with even greater recovery to be found for M5 owners. Here are the heat soak-related torque losses Turner experienced:
Stock IAT location:
18rwtq at 2500rpm
10rwtq at 3000rpm
9rwtq at 3700rpm
Turner IAT Relocation:
7rwtq at 2500rpm
5rwtq at 3000rpm
5rwtq at 3700rpm
**Click here for installation instructions**
The Turner engineering team designed a complete plug and play kit (unlike all other options on the market) that makes for quick, easy, and reversible installation. Weather-sealed connectors keep out the elements, while sheathed wiring offers a clean appearance underhood. With a harness nearly 3 feet long - the Turner IAT relocation kit offers flexibility in positioning, but not too long that you're left with unsightly excess wiring. Turner recommends positioning the sensor in a location away from engine heat, but still within the intake ducting to achieve accurate intake temp readings - such as the far side of the base of the airbox. Vehicles with cold air intakes with cone-style filters can even position the sensor in the end of the filter. Simply drill a hole in your (cool) location of choice and plug in the harness. More information including installation instructions and some good examples of sensor mounting locations can be found in our DIY PDF.
We include everything you need to relocate your IAT, just select your desired sensor brand below - Genuine BMW or original equipment Beru.
Also the perfect plug-n-play option for anyone looking to upgrade their intake to utilize an Alpha-N tune!
Note for vehicles with M62 engine: applicable to 1999 and up
This product was last offered at the strikethrough price on
06-14-2026
This product was last offered at the strikethrough price on
06-14-2026
This product was last offered at the strikethrough price on
06-23-2026
This product was last offered at the strikethrough price on
06-23-2026
This product was last offered at the strikethrough price on
05-03-2026
This product was last offered at the strikethrough price on
05-03-2026
This product was last offered at the strikethrough price on
05-03-2026
This product was last offered at the strikethrough price on
05-03-2026