BMW Drivetrain Parts

Engineered in-house, our torque plate is designed to provide a robust and uniform clamping surface between the flywheel and crankshaft across a range of BMW engine applications. Compatible with both factory and Turner performance flywheels, it helps prevent surface galling and ensures consistent torque distribution during installation.

Features:

Prevents galling and wear at the crankshaft-to-flywheel interface under high clamping loads
Promotes even load distribution for improved fastener integrity and long-term reliability
Compatible with a variety of BMW flywheel setups, including OEM and aftermarket configurations
Design:

Precision-machined from cold rolled steel for high strength and dimensional accuracy
Heat treated to 32 HRC for increased surface hardness and wear resistance
Clear zinc anodized for enhanced corrosion protection
Laser-etched Turner logo
Ideal for performance builds and drivetrain refreshes, this torque plate is a critical component for maintaining proper flywheel installation and maximizing long-term durability across multiple BMW platforms.

The ULTIMATE shifter upgrade for your BMW! Experience more precise throws, less shift lever travel, and an all-around transformation in your shifting experience.

For dozens of years, enthusiasts have critiqued the imprecise and vague feeling of BMW manual transmissions. Plagued with long throws, fore and aft play in gear, and a generally loose feeling, your OEM BMW shifter leaves much to be desired. While most standard carrier-mount short throw shifter kits will aid in reducing throw length and eliminating side-to-side play in gear, some enthusiasts long for a hardcore, race-inspired shifter that completely removes play and excessive throw length. At Turner Motorsport we share the same desire and set out to offer the ULTIMATE upgrade with this Performance Chassis Mount Short Shifter.

WHY UPGRADE?

Factory BMW shifter assemblies are complex by nature. The main component of this assembly is the shift carrier, a cast aluminum piece positioned inside the transmission tunnel that incorporates bushings at both ends for mounting. Like most factory parts, these bushings are designed to reduce NVH (noise, vibration, and harshness) transmission to the cabin. To the spirited driver, however, these bushings translate to flex and vagueness in the shift lever. Moreover, because this carrier is mounted to both the transmission and the body, the entire shifter assembly will "float" with the driveline, further increasing the vague and imprecise feeling of your shifter.

Our Performance Chassis Mount Short Shifter removes the shift carrier assembly entirely—removing any prospect of flex caused by bushings or driveline movement. By contrast, this chassis mount shifter offers a drastic reduction in shift lever travel, vagueness, and side-to-side play. An elevated base allows for moving the fulcrum point upwards, resulting in a much shorter and more precise throw. Shift times are further reduced by a tall, "rally style" shift lever, used to aid in leverage while also bringing the lever closer to the steering wheel. Our design incorporates a proprietary centering spring design, which is adjustable for increasing or decreasing self-centering force. In short, this design eliminates all the drawbacks of your factory BMW shifter, translating to more control, greater precision, shorter throws, and faster shift times.

FEATURES & BENEFITS

Reduced Throw: Modified shifter geometry and heightened fulcrum point translate to a shorter shift lever throw
Improved Shifter Feel: Eliminating the shift carrier and associated bushings drastically reduces "slop" and side-to-side play in the shift lever
Increased Precision: Mounting the shifter to the chassis allows for little to no variation in gear selection
Universal Fitment: Fits many BMW chassis with the provided base plate and hardware (see "Fits These Cars" for exact fitment information)
DESIGN

6061 aluminum, 4130 steel, and 316 stainless steel construction
A type-II black anodized finish
Adjustable self-centering spring
"Rally Style" shift lever
Spherical bearing pivot with maintenance-free brass insert
Product Development:

Our Chassis Mount Shifters are designed, engineered, tested and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer and rigorous long term product testing.

The factory BMW S65 dual-mass flywheel is engineered with comfort in mind, catering to the luxury-oriented expectations of the brand’s driving experience. Its design focuses on dampening drivetrain vibrations, smoothing out gear transitions, and minimizing harshness during operation. However, this refinement costs valuable performance. The dual-mass flywheel adds a substantial 27 lbs of rotational mass to the drivetrain, which significantly hinders throttle response and makes rev-matching feel sluggish and disconnected. Moreover, dual-mass flywheels are notorious for being a weak link in modified or high-performance builds and can prove costly to replace when they inevitably fail.

Our Single-Mass Lightweight Flywheel Conversion addresses all of these shortcomings with a purpose-built, lightweight, single-mass design that prioritizes performance. Weighing in at only 19 lbs., this design significantly reduces rotational mass, allowing your S65 to achieve its true motorsport potential!

Features & Benefits:

Precision machined from 4140 HT heat-treated chromoly steel for exceptional toughness, even wear properties, and increased durability.
Material quality promotes even wear across the entire friction surface, prolonging component lifespan.
Heat treated to HRC 28-32, tempered to relieve stress and improve dimensional stability.
Hardness improves component wear characteristics.
Black oxide coated for corrosion resistance on non-friction surfaces.
Precision balanced to exceed OEM specification (G16 spec to 175g-mm).
Specifically designed to work with S65 OE-architecture clutches.
Optimized step height maximizes clutch clamp load and offers a prolonged service life.
Performance:

8 lbs. lighter than the factory BMW flywheel!
OEM Dual-Mass: 27 lbs.
Turner Motorsport Single-Mass: 19 lbs.
Faster revs
Improved throttle response and acceleration
Allows for a more engaging driving experience and delivers a feeling of direct connection
Installation:

Flywheel Hardware: For added peace of mind, apply Blue or Orange Loctite when installing factory flywheel bolts that do not come with pre-applied threadlocker.

Used when retrofitting an OEM or aftermarket CSL intake on a vehicle with SMG transmission.

Its no secret the CSL intake plenum is the pivotal upgrade for your S54. If you are fortunate enough to have an SMG equipped vehicle you are going to need a bracket to relocate the expansion tank. Our Turner motorsport bracket fits perfectly with the engine bay to facilitate the installation of your genuine or Turner branded CSL intake plenum.

Design:

Direct fit, perfect OEM replacement
304SS sheet metal design, engineered to be simpler and cheaper than its formed OE counterpart
Reverse engineered with FARO laser scanning and Solidworks CAD technology

Over time, factory rubber bushings and plastic components break down, leaving your shifter feeling loose, vague, and disconnected. That lack of precision doesn’t just dull the driving experience—it takes away from the performance BMWs are known for. If your G8X shifter isn’t delivering the crisp engagement you expect, we've developed an all-inclusive fix.

The Ultimate G8X Shifter Rebuild & Upgrade Kit has been expertly crafted by our team of BMW enthusiasts to bring back the sharp, direct shifting feel your BMW deserves. This all-in-one kit combines high-performance upgrades with refreshed OEM hardware, offering a complete overhaul for your shifting system:

Turner Motorsport G8X Dual-Shear Selector Rod (DSSR)

Dual-contact design delivers smoother, more accurate gear changes compared to the OEM single-sided rod

Precision-machined from 6061-T6 billet aluminum for strength and durability

Includes custom-fit shims and connecting pins for easy installation

Maintains factory 232mm length, ensuring there is no change to the factory shift knob position

Replaces OEM Part #: 25118097173

Turner Motorsport G8X Polyurethane Rear Shifter Bushing

Ditch the soft factory rubber! This polyurethane upgrade reduces play and sharpens feedback

CNC-machined aluminum housing with 70A high-durometer polyurethane insert

Corrosion-resistant Type II anodized finish

Replaces OEM Part #: 25118623459

ECS Teflon Shifter Bushing Kit

Replaces the front rubber bushing with low-friction, long-lasting Teflon

Reduces side-to-side play in the shifter carrier

Includes new carrier pins for a complete install

Replaces OEM Part #: 25117507695

Also included are essential Genuine and OE components to ensure a full-service refresh:

BMW Shifter Rod Joint – 25117580281

Vaico Circlips (Qty 2) – 25117571899

Bremmen Shifter Ball Bushing – 25111220600

Experience precision like never before—upgrade your shifting experience today with the Ultimate Shifter Rebuild & Upgrade Kit.

Automatic transmissions are reliable, shift smoothly, and can last without issue so long as they are properly maintained. Over time, the transmission fluid becomes thick and the filter becomes contaminated with small metal particles. This can cause excess wear, high transmission operating temperatures, and eventual failure. To prevent this we recommend changing your filter, fluid, and seals to ensure your transmission continues to operate flawlessly. We recommend filter and fluid changes every 50,000 miles. This filter fits A5S440Z automatic transmissions on BMW E39 540I E38 740I 740IL E31 840I 840CI E53 X5 4.4I 4.6IS

Kit Contains:

• 1 x 24341422673- Transmission Filter
• 1 x 24111422676- Gasket for Transmission Filter
• 1 x 24341422152- O-ring for Transmission Filter

This item fits the following BMWs:
1/1997-2003 E39 BMW 540i 540I wagon
1/1997-2001 E38 BMW 740i 740il
1/1997-1999 E31 BMW 840ci
2000-2003 E53 BMW X5 4.4i X5 4.6is