We are proud to bring out this truly awesome product that makes getting the required Flex Fuel hardware on your BMW with incredible ease and minimal effort, in your own driveway.
Our kit is entirely plug-and-play with the factory vehicle harness. No cutting or splicing of OEM wiring/connectors. It installs in minutes and can be removed without a trace on the car!
Our team used SolidWorks to design a Flow Optimized Flex Fuel Sensor Adapter (FFSA) to ensure fuel flow is unobstructed and with no added pressure drop at full fuel pump flow from the fuel tank to your motor when our kit is installed. This is important when pushing the factory fuel system with all the power Ethanol can provide over petrol!
Flex fuel sensor housing is designed to neatly install into the factory BMW fuel hat location.
Flex Fuel Sensor Adapter also contains two 1/8 NPT ports that allow installation of an auxiliary Fuel Pressure sensor for vehicles that don’t come with an OEM one from the factory for future use. Depending on fitment, either port can be used.
Install the bootmod3 Flex Fuel Plug and Play Kit and flash your flex fuel enabled bootmod3 OTS MultiMap or Custom Map in minutes and you’re off to the races never worrying about alcohol/petrol blend % in your fuel tank. It does not get better or easier than this!
bootmod3 FlexFuel Plug and Play Kit:
Minutes to install at home as opposed to hours at a shop with car up on lift fabricating/cutting into factory fuel lines and splicing/cutting/pinning into OEM electrical
4+ hours in time/cost savings to get going on Flex Fuel as compared to most other kits that require making custom fuel lines, fittings, and custom wiring!
Fully reversible/removable and back to stock without a trace in minutes
Custom 3-piece Aluminum-6061 Flex Fuel sensor adapter with built-in sensor bypass to allow for obstruction-free fuel flow made to fit in the vehicle factory fuel hat area below the rear seat
All connecting points are sealed with fuel-safe Viton O-rings
Flex Fuel Sensor Adapter housing provides additional 1/8 NPT ports for optional Fuel Pressure sensor addition to vehicles without a factory one for bootmod3 CustomROM v2 support
CANBUS Enabled Ethanol Content Analyzer (ECA) that integrates with bootmod3 CustomROM for complete and seamless conversion of your BMW to FlexFuel for bootmod3 Flex Fuel enabled OTS MultiMaps and custom tunes with your bootmod3 tuner of choice
Power/CANBus 4-wire plug-and-play harness
100% Fully Plug and Play harness to the BMW Fuel Controller connectors (EKP3) on S55, N55 vehicles
100% Fully Plug and Play harness on the BMW Body Domain Controller (BDC/FEM) connector on Gen1 F-series B48/B58
Continental Flex Fuel sensor 3-wire harness
Custom Aluminum-6061 CANBus Enclosure for the bootmod3 ECA board
Custom, kink-free teflon braided line allowing plug-and-play installation with the OEM fuel hat and factory 5/16” or 3/8” fuel feed line. No cutting or new lines required.
-6 AN fitting by Racetronix
Not for sale or use in the state of California on any pollution-controlled vehicle as per the California Air Resources Board.
Prop 65 Warning
Product Q&A
Lifetime Replacement
This Product Is Covered By Our Lifetime Replacement Program
Products protected by our Lifetime Replacement Program are covered for as long as you own the product, no need to worry about an expiration date. Purchase your products and enjoy some worry-free motoring, knowing we've got you covered.
If you have any questions, would like to learn more or are ready to place a replacement claim, click here!
Fits These Cars
MAKE
MODEL
SUBMODEL
ENGINE
Special Fitment Notes
BMW
G80
M3
S58 3.0L
Use vehicle selector to confirm fitment
BMW
G80
M3 Competition
S58 3.0L
Use vehicle selector to confirm fitment
BMW
G80
M3 Competition xDrive
S58 3.0L
Use vehicle selector to confirm fitment
BMW
G82
M4
S58 3.0L
Use vehicle selector to confirm fitment
BMW
G82
M4 Competition
S58 3.0L
Use vehicle selector to confirm fitment
BMW
G82
M4 Competition xDrive
S58 3.0L
Use vehicle selector to confirm fitment
BMW
G83
M4 Competition xDrive
S58 3.0L
Use vehicle selector to confirm fitment
BMW
G87
M2
S58 3.0L
Use vehicle selector to confirm fitment
*The above product applications have been written by Turner Motorsport. All
warranties, product application, fitment, and performance are the responsibility of Turner Motorsport.
For additional information see the terms of use.