High-flow 2.5" MMP inlets drastically reduce compressor intake restriction, but introducing aftermarket silicone couplers, relocated piping, and upgraded intercooler connections creates multiple new potential failure points. When pressurized charge air escapes under load, the DME compensates by driving wastegate duty cycle higher to hit target load, pushing the twin turbos outside their efficiency island, spiking IATs, and accelerating thrust bearing wear. Because OEM-sized testers cannot seal larger 2.5" aftermarket inlets, a dedicated solution is mandatory for proper post-install verification and track-day prep.
Engineered specifically for both relocated and stock-location 2.5" MMP inlets, this dual cap kit isolates and statically pressurizes the entire cold and hot side intake tract. By capping both compressor inlets alongside the diverter valve returns and crankcase breather port, you can compare incoming compressor air against static system pressure on the dual gauges to accurately quantify bleed-down rates and isolate pinhole leaks.
Dual End-Cap Assemblies: Twin 2.5" end caps machined with 1/8" NPT threaded gauge and fill ports to simultaneously seal both turbocharger intake paths.
Precision Gauges & Fill Valves: Includes dual 30 PSI / 1 Bar mechanical boost gauges for real-time pressure monitoring and leak-down diagnostics, paired with standard Schrader valves (removable to accept 1/4" NPT quick-disconnect fittings).
Clamping & Isolation Hardware: Supplied with (2) stainless steel T-bolt clamps with Teflon lock-nuts for blow-off-free retention and (3) vinyl block-off caps for isolating diverter valve return ports and the rear valve cover PCV breather.
Prop 65 Warning
Product Q&A
Lifetime Replacement
This product is not eligible for Lifetime Replacement
Fits These Cars
MAKE
MODEL
SUBMODEL
ENGINE
Special Fitment Notes
BMW
E60
535i
N54 3.0L
For vehicles with MMP 2.5" inlets only - not for factory intakes
BMW
E60
535xi
N54 3.0L
For vehicles with MMP 2.5" inlets only - not for factory intakes
BMW
E61
535xi
N54 3.0L
For vehicles with MMP 2.5" inlets only - not for factory intakes
BMW
E82
1 M Coupe
N54 3.0L
For vehicles with MMP 2.5" inlets only - not for factory intakes
BMW
E82
135i
N54 3.0L
For vehicles with MMP 2.5" inlets only - not for factory intakes
BMW
E88
135i
N54 3.0L
For vehicles with MMP 2.5" inlets only - not for factory intakes
BMW
E90
335i
N54 3.0L
For vehicles with MMP 2.5" inlets only - not for factory intakes
BMW
E90
335xi
N54 3.0L
For vehicles with MMP 2.5" inlets only - not for factory intakes
BMW
E92
335i
N54 3.0L
For vehicles with MMP 2.5" inlets only - not for factory intakes
BMW
E92
335is
N54 3.0L
For vehicles with MMP 2.5" inlets only - not for factory intakes
BMW
E92
335xi
N54 3.0L
For vehicles with MMP 2.5" inlets only - not for factory intakes
BMW
E93
335i
N54 3.0L
For vehicles with MMP 2.5" inlets only - not for factory intakes
BMW
E93
335is
N54 3.0L
For vehicles with MMP 2.5" inlets only - not for factory intakes
BMW
Z4
sDrive35i
N54 3.0L
For vehicles with MMP 2.5" inlets only - not for factory intakes
BMW
Z4
sDrive35is
N54 3.0L
For vehicles with MMP 2.5" inlets only - not for factory intakes
*The above product applications have been written by Turner Motorsport. All
warranties, product application, fitment, and performance are the responsibility of Turner Motorsport.
For additional information see the terms of use.