BMW Tools & Specialty Equipment for BMW E12 530i M30 3.0L

PRESSURE BRAKE BLEEDER:

We know bleeding brake alone is not only no fun, but much more complicated than it needs to be. Having a pressure bleeder give you the ability to keep the pressure on the brake system while you go under and crack open the bleeder screws to relieve the air pockets.

Features:

• Holds a full 3-Liters (3.17 qts) of brake fluid
• Easy to read 0-30 lbs pressure gauge built into the tank top
• Pressure relief valve for safe release of pressure
• 40" hose with detachable swivel fitting

FLUID CATCH BOTTLE:

keep your fluid's off the floor and into our catch bottle.  The bottle has fluid level markings from 0.2L to 0.7 liter. This feature allows you to measure how much fluid you have sent thru the system.  Our bleeder bottle features an expandable/collapsible top portion for easier storage. Gasket in cap prevents leakage. Tubing is extra long at 24" from cap to nipple. Flexible hose can be pushed down into bottle for storage when done. Bottle now features a handy hanger bracket to hang bottle from bottom of car.

Note:

• Do not exceed 20 PSI
• LIFETIME REPLACEMENT

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

46 PIECE SET:

This 1/4" set contains all the most popular tools needed to get the job done on your European car repair.

Kit Contains:

-13PCS-1/4" DR.6PT SOCKETS: 4, 4.5 , 5 ,5.5 ,6 , 7, 8 ,9 ,10, 11, 12, 13, 14MM 

-1PC- 1/4" DR. QUICK RELEASE RATCHET (72T).

-2PC- 1/4" DR.50 & 100MM EXTENSIONS 

-1PC- 1/4" DR.150MM FLEXIBLE EXTENSION

-1PC- 1/4" DR.UNIVERSAL JOINT

-1PC- 1/4" DR.SLIDING T-BAR

-1PC- 1/4" DR.6" SPINNER HANDLE

-1PC- 1/4" DR.1/4" BIT HOLDER ADAPTER

-4PCS-HEX KEY WRENCHES:1.27, 1.5,2,2.5MM

-6PCS-1/4" HEX SOCKETS:3,4,5,6,7,8MM

-3PCS-1/4' SLOTTED SOCKETS:4,5.5,7MM

-3PCS-1/4" PHILIPS SOCKETS:PH1, PH2, PH3

-3PCS-1/4"POZI SOCKETS: PZ1, PZ2, PZ3

-6PCS-1/4" TORX SOCKETS: T10, T15, T20, T25, T30, T40

TRIM/MOLDING SET:

Plastic five-piece tool kit removes trim and door panels, moldings, and adhesive backed logos and badges, without damage.

Made of impact resistant plastic that will not mar surfaces as metal screwdrivers and pry bars will. Slim design for delicate work in tight areas.

Kit includes:

• Wide edge remover

• Narrow edge remover

• Pull-type remover

• Handle remover

• Upholstery clip remover

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

BRAKE BLEEDER:

We know bleeding brake alone is not only no fun, but much more complicated than it needs to be. Having a pressure bleeder give you the ability to keep the pressure on the brake system while you go under and crack open the bleeder screws to relieve the air pockets.

Features:

• Holds a full 3-Liters (3.17 qts) of brake fluid
• Easy to read 0-30 lbs pressure gauge built into the tank top
• Pressure relief valve for safe release of pressure
• 40" hose with detachable swivel fitting

Note:

• Do not exceed 20 PSI
• LIFETIME REPLACEMENT

Includes:

• 3 Liter (3.17 qts) storage tank
• Pressure cap with 0-30 lb gauge and pressure relief valve
• 40" hose
• Dual preventative fittings on the hose, featuring a chrome quick coupler on one end to snap onto the master cylinder cap and a detachable swivel fitting on the other end

Note:

• Recommend working at 10 PSI
• Dimensions for cap seal: 12x21x4 mm
• LIFETIME REPLACEMENT

CATCH BOTTLE:

Keep your fluid's off the floor and into our catch bottle.  The bottle has fluid level markings from 0.2L to 0.7 liter. This feature allows you to measure how much fluid you have sent thru the system.  Our bleeder bottle features an expandable/collapsible top portion for easier storage. Gasket in cap prevents leakage. Tubing is extra long at 24" from cap to nipple. Flexible hose can be pushed down into bottle for storage when done. Bottle now features a handy hanger bracket to hang bottle from bottom of car.

CALIPER HOOK SET:

Tired of messing with bent coat hangers or bungee cords to hang your calipers up and out of the way when performing brake maintenance? These hooks make working on your brakes easier by letting you hang your calipers with ease, no more fighting with the bungee cords or zip ties to hold the caliper just right or having to make your own "custom" hooks with wire.

• Holds brake calipers out of the way while working on brakes
• Also use to hang other automotive parts and tools while working on your vehicle.
• Stronger than zip ties or wire.
• Save the brake hose by not hanging caliper by hose.
• Made of  thick steel for strength and durability. length is 8"

BILLET ALUMINUM CAP:

This aluminum cap with 90 degree swivel will work with our T#363245 Euro bleeder or our T#366970 3-Liter Multi-functional Fluid Pump Kit.

Features an all aluminum 45mm cap with quick coupler nipple.

BLEEDER WRENCH:

Finally, a bleeder wrench with just the right angle to open the bleeder screw without having to spend all that time removing each wheel from your car.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Looking for the best of the best in your search for a floor jack? AC Hydraulic's DK20Q Hydraulic Floor Jack is the answer. This jack is built to take anything you can throw at it and keep on going. Using a wide and robust high-strength steel frame, blue powedercoat paint protection, and built-in safety overload valve, this jack was designed in mind to outlast us all!

Features:

• Very low minimum height of only 3.15 inches
• Wide and robust frame made of high-strength steel
• Precise and safe control whilst lowering
• Manual dead man’s release for optimum safety when lowering
• Built-in safety overload valve
• Noiseless wheels incorporating a polyurethane central O ring offers maximum surface protection
• Ergonomically designed handle ensuring positive and safe operation
• DK20Q is fitted with quick-lift pedal for easy reach of lifting point

Specifications:

• Capacity:  4400 lbs
• Min. height:  3.15 inches
• Max. height:  19.49 inches
• Frame length:  25.98 inches 
• Handle length:  37.40 inches
• Frame height:  6.30 inches 
• Width:  16.14 inches
• Weight:  68 lbs

The VIM Tools 12" Magrail is a robust and adaptable magnetic socket organizer, perfect for keeping your sockets and hand tools securely in place. Its low-profile, anodized aluminum base ensures durability and a streamlined look, making your tools easy to organize and access.

Key Features:

• Powerful Neodymium Magnets: Keeps sockets and tools firmly in position, regardless of orientation.
• Durable Anodized Aluminum Base: Lightweight and built to last.
• Slim Profile: Dimensions are 3/16” tall, 1” wide, and 12" long.
• Color Variety: Available in various colors.
• Customizable: Studs sold separately in various packs for 1/4 in., 3/8 in., 1/2 in., 3/4 in., and 1 in. drive sockets.

The cutting-edge GENIUS1 is a powerhouse among our chargers renowned for its exceptional performance, energy efficiency, and compact design. The GENIUS1 is a versatile 6-volt and 12-volt charger, maintainer, and desulfator with a 1-amp rating. It's engineered to work with lead-acid batteries in automotive, marine, and deep-cycle applications, supporting flooded, gel, AGM, maintenance-free types, and even lithium-ion batteries.

Features: 

• Do more with Genius - Designed for 6-volt and 12-volt lead-acid automotive, marine, and deep-cycle batteries, including flooded, gel, AGM, and maintenance-free, plus lithium-ion batteries.
• Enjoy precision charging - An integrated thermal sensor detects the ambient temperature and alters the charge to eliminate over-charging in hot climates and under-charging in cold climates.
• Charge dead batteries - Charges dead batteries as low as 1-volt. Or use the all-new Force Mode that allows you to take control and manually begin charging dead batteries down to zero volts.
• Simple to set up and use - Plug-in, connect to the battery, select a charge mode, and start charging your battery. A fully-automatic, worry-free battery charger for year-round use.
• Restore your battery - Detects sulfation and acid stratification and restores lost performance for stronger engine starts and extended battery life.
• Compatible with all types of vehicles - Charge and maintain cars, motorcycles, lawnmowers, ATVs, tractors, trucks, SUVs, boats, classic cars, hot rods, and more - you name it.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

The Adjustable Hood Prop is a versatile tool designed to securely hold hoods, doors, or trunk lids open during repairs or bodywork. With an adjustable length from 28 to 46 inches, it's perfect for various tasks.

It is not intended for heavy-duty support, with a maximum weight capacity of 50 lbs.

Key Features:

• Adjustable Length: Extends from 28 to 46 inches for versatile use.
• Secure Hold: Keeps hoods, doors, or trunk lids open during repairs or bodywork.
• Easy Setup: Simple to position and secure with telescoping rod.
• Weight Capacity: Supports up to 50 lbs.
• Lifetime Warranty: Ensures long-term reliability.