BMW 6 Series E24 (1977-1989)

CNC Billet License Plate Bracket

T#:27105150

Part#: RE.061

Ships in 3 Business Days

$ 119.00 USD

Add to Wish List

Qty

$ 119.00 USD

Add to Wish List

You are looking at the BEST license plate bracket for your BMW, price no object! We never understood why BMW would put a cheap, plastic bracket on the back of a BMW to hold a license plate. The screws holding the bracket on would rust, the steel inserts hold the plate on would also rust, causing the hardware holding the plate on to seize or just no longer function. Our bracket fits any BMW that mounts license plates in the rear that use factory part number 51-18-8-238-061. Fits most BMWs produced AFTER 1999. If your vehicle does not use the plastic plate, it will not fit. Does not fit E46 touring (wagon). PROBLEMS with the factory bracket and hardware The screws that secure the plastic bracket are plated steel and will corrode over time. These two screw would normally not be seen since it is under the license plate, but it is holding the bracket onto the trunk. The four (4) nutserts that are pressed into the plastic frame (to hold the license plate) are also steel and will eventually seize with the bolt and just spin in the plastic frame becoming useless. The plastic frame itself is flimsy, doing a near minimal task of holding on the license plate. The hardware securing the plate to the bracket will rust, seizing to the nutsert or even spinning in place becoming completely useless. SOLUTION Create a more robust bracket that would not only be stiffer but also more corrosion resistant; CNC’d aluminum with an anodized finish. We machine a near identical plate, matching factory dimensions, from 1/2" plate of aluminum. Instead of nutserts pressed into plastic, map the correct position and machine the threads for the hardware directly into the plate. The hardware used to secure the new bracket to the trunk would be made from stainless steel (or optional corrosion-proof titanium) The hardware used to secure the license plate to the newly engineered bracket would also be stainless steel (or optional made from titanium) Kit Includes: One (1) Rogue Engineering designed and manufactured CNC'd aluminum license plate bracket Two (2) Stainless screws to secure bracket to trunk. Four (4) stainless screws to secure license plate to bracket.

Show More Show Less

AeroCatch Racing Hood and Body Panel Fasteners (Pair) - Better than h...

T#:340098

Part#: AEROCATCH

In Stock

$ 566.99

This product was last offered at the strikethrough price on
05-13-2026

Starting at $ 82.99 USD

Add to Wish List

Starting at $ 82.99 USD

Add to Wish List

As used by Turner Motorsport on our championship winning BMW race cars, the new aerodynamically efficient and aesthetically styled AeroCatch is setting new standards in hood fixing for the 21st century. Say goodbye to your standard hood pins -- these are better all around.

Show More Show Less

E34 M5 JB Racing Lightweight Aluminum Flywheel

T#:3772

Part#: 520-090-240

Ships in 4 Business Days

$ 581.00 USD

Add to Wish List

Qty

$ 581.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable.

Stock Flywheel Weight = 16.0lbs
JB Flywheel Weight = 8.0lbs

This item fits the following BMWs:
1991-1995 E34 BMW M5

Show More Show Less

Active Autowerke Rotrex Traction Fluid - One Liter

T#:397307

Part#: 12-032

Ships in 1 Business Day

$ 240.00 USD

Add to Wish List

Qty

$ 240.00 USD

Add to Wish List

Rotrex superchargers utilize a unique traction drive system that sets it apart from other centrifugal-style superchargers. For best performance, Rotrex recommends replacing this fluid every 50,000 miles. This bottle of traction fluid is plenty enough for one supercharger service (typically 750ml).

Show More Show Less

E24 633/635CSi/M6, E28 535i/M5 JB Racing Lightweight Aluminum Flywhee...

T#:3770

Part#: 520-080-240

Ships in 6 Business Days

$ 630.00 USD

Add to Wish List

Qty

$ 630.00 USD

Add to Wish List

Aluminum flywheels are much lighter than the stock steel flywheel and that produces better throttle response and more available horsepower to the wheels for faster acceleration. The JB Racing aluminum flywheels are a direct replacement for the stock flywheel and work with stock clutch components for an easy upgrade with very little downside.

Modern flywheels are built with additional components and features that are designed to dampen and minimize vibrations from the engine and transmission. As a result they have become bloated in weight and that means more energy is used up just making the flywheel spin. The weight difference between an aluminum and steel flywheel is huge - sometimes more than 50% less. Without the additional mass, more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance.

In addition to releasing more power to the wheels, the lighter flywheel allows the engine to spin more freely, which improves throttle response. Again, the difference is huge as you watch the revs build faster than before. With the engine spinning easier the power band comes up much sooner. The stock steel flywheel feels lazy in comparison. There is a driving adjustment required to get used to how much faster the engine revs but that's not really a downside.

The JB lightweight flywheel is designed to be used with a factory organic clutch - the same clutch kit that you would get from any BMW dealer. This makes replacement clutch components easy to source and inexpensive when compared to specialized racing clutches. By using the factory BMW clutch, JB has also made the whole assembly easy to live with when used on the street. The clutch behaves the same as it originally did - just with better throttle response and more power! The JB flywheel can also be rebuilt with a new clutch contact surface - you don't have to buy a new flywheel.

Aluminum flywheels are considered 'single-mass' flywheels because they do not have the same dampening designs as an original 'dual-mass' flywheel. With a single-mass design more noise and vibration may be noticeable. There are steps you can take to minimize the noise - heavier weight transmission oil and clutch discs with anti-rattle springs (sprung-hub clutch).

Stock Flywheel Weight = 22.0lbs
JB Flywheel Weight = 8.5lbs

This flywheel includes the ignition trigger wheel.

This item fits the following BMWs:
1982-1987 E23 BMW 733i 735i
1982-1989 E24 BMW 633csi 635csi M6
1985-1988 E28 BMW 535i 535is M5

Show More Show Less

Adjustable Front Camber Bushings

T#:31522921

Part#: 193616-6H

Ships on Aug 18, 2026

$ 320.00 USD

Add to Wish List

Qty

$ 320.00 USD

Add to Wish List

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E24, E28,...

T#:389654

Part#: 193316-1J

In Stock

$ 379.99 USD

Add to Wish List

Qty

$ 379.99 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
1984-1991 E30 BMW 318i 318is 318ic 325e 325es 325i 325ic 325is M3
1982-1988 E28 BMW 528e 533i 535i 535is M5
1993-1995 E34 BMW 525i
1982-1989 E24 BMW 633csi 635csi M6

Show More Show Less

Active Autowerke Signature Trunk Emblem

T#:590914

Part#: AASIGNATUREPLAQU

Ships in 3 Business Days

4% off MSRP $ 45.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 43.00 USD

Add to Wish List

Qty

4% off MSRP

$ 45.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 43.00 USD

Add to Wish List

Stand out from the crowd, and give them a hint of what you've got going on under the hood, with the official Active Autowerke Signature Emblem! The emblem can be placed anywhere on the exterior, or interior of your BMW. Hefty stainless steel construction and durable double-sided tape will help ensure that it is never lost, even at speeds over 170+ MPH...Don't ask us how we know! Represent your favorite BMW tuner for all to see today!

Show More Show Less

Adjustable Rear Camber/Toe Bushings

E24: Production Dates to 1977- 4/1982

T#:582353

Part#: 192026G

In Stock

$ 320.00 USD

Add to Wish List

Qty

$ 320.00 USD

Add to Wish List

KMAC Street Rear Adjustable Camber/Toe Bushings - E23, E24 83-89, E28...

T#:3546

Part#: 193326

Special Order: No Guaranteed ETA

$ 269.95 USD

Add to Wish List

Qty

$ 269.95 USD

Add to Wish List

Perfect for lowered cars that need to dial out negative camber to preserve tires. Also perfect for track cars - easily dial in toe and camber for the track for better handling. Priced per set.

Fits the following BMW:
E23 BMW 7 series
83-89 E24 BMW 6 series
82-88 E28 BMW 5 series
E32 BMW 7 series
E34 BMW 5series

Show More Show Less

APR Black Valve Stem Caps - Pack of 4

Call In Or Chat For Best Price!
Call In, Chat, Or Email, For Best Price! Limited Time Only!

T#:22987107

Part#: MS100197

In Stock

11% off MSRP $ 17.94

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 15.95 USD

Add to Wish List

Qty

11% off MSRP

$ 17.94

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 15.95 USD

Add to Wish List

APR Black Valve Stem Caps are a stylish and functional upgrade for your vehicle's wheels. Sold as a set of four, these high-quality aluminum caps feature an engraved APR logo on each cap. Designed to add a touch of customization to your vehicle, they also serve a practical purpose.

Premium Quality: Made from durable aluminum for long-lasting performance.
Enhanced Aesthetics: Features an engraved APR logo for a sleek and stylish look.
Functional Design: Helps protect valve stems from dirt and moisture.
Easy Installation: Simple to install and compatible with most standard valve stems.

Upgrade your vehicle with APR Black Valve Stem Caps to enhance both style and functionality.

Show More Show Less

APR Valve Stem Caps - Set Of 4 - Silver

Call In Or Chat For Best Price!

T#:31125602

Part#: MS100178

In Stock

11% off MSRP $ 17.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 15.99 USD

Add to Wish List

Qty

11% off MSRP

$ 17.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 15.99 USD

Add to Wish List

APR Valve Stem Caps - Set Of 4 - Silver are a stylish and functional upgrade for any vehicle. This set includes four high-quality aluminum valve stem caps, each engraved with the distinctive APR logo. These caps are designed to enhance the appearance of your wheels while providing durability and reliability.

Stylish Appearance: Each cap features a sleek silver finish and an engraved APR logo, adding a touch of elegance to your vehicle.
Durable Construction: Made from high-quality aluminum, these valve stem caps are built to withstand harsh conditions and resist corrosion.
Easy Installation: Simple to install and compatible with most standard valve stems.
Enhanced Wheel Aesthetics: Upgrades the look of your wheels with a subtle yet impactful design.
Functional Protection: Helps protect valve stems from dirt and moisture, ensuring consistent performance.

This set of valve stem caps is an excellent choice for anyone looking to add a refined touch to their vehicle's wheels.

Show More Show Less

APR Valve Stem Caps - Set Of 4 - Gunmetal

Call In Or Chat For Best Price!

T#:31092523

Part#: MS100179

In Stock

11% off MSRP $ 17.94

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 15.95 USD

Add to Wish List

Qty

11% off MSRP

$ 17.94

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 15.95 USD

Add to Wish List

APR Valve Stem Caps - Set Of 4 - Gunmetal offer a stylish and functional upgrade for any vehicle. These high-quality aluminum valve stem caps come in a sleek gunmetal finish and feature an engraved APR logo, which adds a touch of sophistication to your wheels.

Material: Made from durable aluminum for long-lasting performance
Design: Engraved APR logo adds a distinctive look
Finish: Gunmetal color enhances the visual appeal of your wheels
Set Includes: 4 valve stem caps for a complete upgrade
Compatibility: Fits most standard valve stems

These APR Valve Stem Caps are designed to provide both aesthetics and durability, making them a great choice for enhancing your vehicle's style.

Show More Show Less

KMAC Stage 3 Track Front Adjustable Camber/Caster Plates - E24, E28, ...

T#:389656

Part#: 193316-3L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Track, Stage 3
Bearing: PTFE-lined pillow-ball, no bushing

KMAC Stage 3 camber/caster plates are designed for track or race-only situations where comfort and noise are not the primary concerns. The Stage 3 camber plates use a pillowball bearing, solidly mounted within the camber plate for direct alignment of the strut shaft and no excess play or deflection. Stage 3 are designed to increase negative camber with their patented 'floating' adjustment that changes camber and caster together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Fitment is limited to race-only small diameter coil-over springs (not stock-type). Bearing inserts and adapters included. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
1984-1991 E30 BMW 318i 318is 318ic 325e 325es 325i 325ic 325is M3
1982-1988 E28 BMW 528e 533i 535i 535is M5
1993-1995 E34 BMW 525i
1982-1989 E24 BMW 633csi 635csi M6

Show More Show Less

KMAC Front Adjustable Inner Thrust Arm Bushing

T#:27205341

Part#: 193316-1H

Special Order: No Guaranteed ETA

$ 320.00 USD

Add to Wish List

Qty

$ 320.00 USD

Add to Wish List

Experience effortless caster adjustment with KMAC's premium inner thrust arm bushings.

Key Features:

1. Patented Design: Enjoy precise adjustments with a single wrench, even under load directly on the alignment rack.

2. Simplified Adjustment: Say goodbye to inaccurate multi-bolt systems and time-consuming disassembly for readjustments.

3. Extensive Adjustment Range: Benefit from the largest and strongest adjustment range available.

4. Mono Ball/Dual-Axis Bushings

5. Enhance brake and steering response with these high-performance bushings.

6. Superior Design: Our unique design surpasses traditional steel spherical bearings, offering over 2 ½ times the load-bearing and impact area.

Upgrade your vehicle's handling and responsiveness with KMAC's innovative inner thrust arm bushings.

Show More Show Less

Project Cars

SELECT YOUR BMW

Sub-Categories

CNC Billet License Plate Bracket

AeroCatch Racing Hood and Body Panel Fasteners (Pair) - Better than h...

E34 M5 JB Racing Lightweight Aluminum Flywheel

Active Autowerke Rotrex Traction Fluid - One Liter

E24 633/635CSi/M6, E28 535i/M5 JB Racing Lightweight Aluminum Flywhee...

Adjustable Front Camber Bushings

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E24, E28,...

Active Autowerke Signature Trunk Emblem

Adjustable Rear Camber/Toe Bushings

KMAC Street Rear Adjustable Camber/Toe Bushings - E23, E24 83-89, E28...

APR Black Valve Stem Caps - Pack of 4

APR Valve Stem Caps - Set Of 4 - Silver

APR Valve Stem Caps - Set Of 4 - Gunmetal

KMAC Stage 3 Track Front Adjustable Camber/Caster Plates - E24, E28, ...

KMAC Front Adjustable Inner Thrust Arm Bushing

Select Vehicle

Purpose

Category

Brand

Price

Shipping

Narrow Results