BMW Suspension Parts for BMW 3 Series E30 (1984-1991)

Swapping in E46 control arms into your E30 or E36 will significantly increase negative camber by widening the track width and will also give you more clearance for more steering angle. Condor's conversion bushings are machined from UHMW due to its high rigidity and low coefficient of friction allowing for minimal suspension bushing deflection (geometry change). They've designed them offset to re-center the wheel and give your e30/e36 the correct caster. They will include a stainless-steel insert that tightly presses over the hex pattern on the E46 control arms. You do not need to grind down your control arms or make any other modifications to your chassis. Please note that you will need to use E36 outer tie rods and E90 inner tie rods when installing in an E30 or E36.

Fitment:
Fits the following Meyle and Lemforder arms with 21-22MM Hex.

LEMFORDER ZHP - 31122282121 & 31122282122
LEMFORDER - 31126777851 & 31126777852
MEYLE HD - 31126777851 & 31126777852
*Please note that Meyle makes a standard e46 control arm and a Heavy Duty control arm. SOME HD arms have a hex that is larger in size. These HD control arms may need to be shaved 1-2 mm for proper fitment.

If your E30 convertible needs a little more pep in the corners, this is an excellent suspension package. H&R Sport springs and Bilstein Sport shocks for the E30 will lower the ride height for an aggressive stance and stiffer springs will improve handling and balance in the corners. This suspension is a favorite among our E30 fans because the car corners better without a punishing ride. Perfect for daily-driven E30s who want to carry more speed through the corners.

H&R Sport springs lower the ride height by 1.4" in the front and .75" in the rear and stiffens the spring rate. Both combine to lower the car's center of gravity and reduce the amount of bodyroll in corners. The springs are progressive rate so their initial stiffness is actually very compliant and it becomes stiffer as the spring is compressed. This is great for street cars that see bumps and potholes where suspension compliance is key. Overall, they are about 40% stiffer than the stock original springs.

We use Bilstein Sport shocks as the dampers and they feature Bilstein's patented and innovative valving system. With this system, small bumps and impacts are absorbed as they should be. But the shocks stiffen for cornering and other suspension motions. It's the best of both worlds as the shock self-adjusts based on suspension motion. These fit with the stock strut and shock mounts, making for an easy and clean install.
 

Parts list:

• 1 set - H&R Sport Springs (50407/50409)
• 1 pair - Bilstein Front Sport strut inserts (P36-0335 / 34-003350)
• 1 pair - Bilstein Rear Sport Shocks (B36-2027 / 24-020275)

Fitment note: Front strut inserts fit the larger 51mm strut housings. These were standard for all 6-cylinder E30s, all M3, and 1989-1992 318i/is. Other models used a smaller strut housing which requires a different Bilstein insert.

This item fits the following BMWs:
1987-1992 E30 BMW 325ic

If E30 needs a little more pep in the corners, this is an excellent suspension package. H&R Sport springs and Bilstein Sport shocks for the E30 will lower the ride height for an aggressive stance and stiffer springs will improve handling and balance in the corners. This suspension is a favorite among our E30 fans because the car corners better without a punishing ride. Perfect for daily-driven E30s who want to carry more speed through the corners.

H&R Sport springs lower the ride height by 1.25" and stiffens the spring rate. Both combine to lower the car's center of gravity and reduce the amount of bodyroll in corners. The springs are progressive rate so their initial stiffness is actually very compliant and it becomes stiffer as the spring is compressed. This is great for street cars that see bumps and potholes where suspension compliance is key. Overall, they are about 40% stiffer than the stock original springs.

We use Bilstein Sport shocks as the dampers and they feature Bilstein's patented and innovative valving system. With this system, small bumps and impacts are absorbed as they should be. But the shocks stiffen for cornering and other suspension motions. It's the best of both worlds as the shock self-adjusts based on suspension motion. These fit with the stock strut and shock mounts, making for an easy and clean install.
 

Parts list:

• 1 set - H&R Sport Springs (50406)
• 1 pair - Bilstein Front Sport strut inserts (P36-0335 / 34-003350)
• 1 pair - Bilstein Rear Sport Shocks (B36-2027 / 24-020275)

Fitment note: Front strut inserts fit the larger 51mm strut housings. These were standard for all 6-cylinder E30s, all M3, and 1989-1992 318i/is. Other models used a smaller strut housing which requires a different Bilstein insert.

This item fits the following BMWs:
1984-1992 E30 BMW 325e 325es 325i 325ic 325is

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 1 kit replaces:

Sway Bar End Links
Strut Mounts & Gaskets
Reinforcement Plates
Trailing Arm Bushings
Hardware