This braided stainless steel line replaces the stock hydraulic hose connecting your clutch slave cylinder to the clutch master cylinder. There are several deficiences with rubber, especially as it ages - when new the rubber expands and swells under pressure and the pedal can feel spongy. As rubber ages and is exposed to extreme temperatures the rubber can harden and even shrink (common on brake hoses), which results in a stiff pedal. Rubber clutch lines do not stand up to the stresses of hard use. ECS Exact-Fit stainless reinforced clutch lines provide more confident and dependable shifting by maintaining consistent line pressure, long lasting corrosion resistance, and increased protection from failure. These lines are reinforced with braided stainless steel mesh, affording superior expansion resistance. This resistance to expansion creates a firmer pedal, and a more direct clutch pedal feel. The signature red polymer coating provides additional protection from the elements and abrasion.

This particular stainless steel clutch line fits the following BMWs:
1996-1999 E36 BMW 323ic 323is 328i 328is 328ic
1995-1999 E36 BMW M3
1993-1995 E34 BMW 530i 540i 

Requires shorter flywheel bolts - 8x (P# 11227805885) - T#12322

Lightweight flywheels have proven themselves to be a worthwhile performance enhancement. But with the quicker throttle response and horsepower improvement comes one serious drawback: flywheel chatter. Without the dual-mass flywheel's rubber isolators, a lightweight aluminum flywheel has more rattle than stock. ECS has designed this flywheel using chrom-moly steel and it weighs almost ten pounds less than the stock DMF but not as extreme as full aluminum flywheels. The steel helps dampen vibration and noise so you get near-factory refinement and most of the benefits of a lightweight flywheel: quicker throttle response, better reliability, and more power to the wheels. This flywheel requires the E34 M5 sprung hub clutch kit.

Modern flywheels are built with additional components that are designed to dampen and minimize vibrations from the engine and transmission. Weight has increased and reliability has decreased. With additional weight more energy is required for it to move. A lightweight flywheel does away with the dual mass design and its additional mass so more energy can be diverted to where it counts most - moving the car. The flywheel and clutch is one of the first areas that engine builders address when making the rotating assembly lighter for race engines. The dampening effect is just not needed on cars that are focused on performance. And with a single-mass flywheel the unreliable DMF design is eliminated.

Stock flywheel weight - 25.0lbs
ECS flywheel weight = 16.55lbs

This item fits the following BMWs:
1992-1999 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2002 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci (5-speed)
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2005 E85 BMW Z4 2.5i Z4 3.0i (5-speed)

Shifter slop is a common complaint among all BMW models. Some of that play comes from the bushings where the shifter carrier mounts to the transmission. The original rubber carrier bushings don't last very long and when they get too soft the shifter flops around. These Teflon bushings are not as stiff as Delrin so they won't transmit as much vibration and buzz in the shifter. Yet Teflon will last much longer than the factory rubber, giving you precise shifting for many years.

Note: this is only one part of the shift linkage and there may be other components that need replacing to improve shifting feel.

We advise getting a replacement bushing carrier pin as well. If the original rubber bushings are worn the pin will have wear too and you will still have slop in the shifter, even with the new bushings.

These are the ROUND shifter carrier bushings (some BMW models have oval bushings).

This item fits the following BMWs:
6/1986-1992 E30 BMW 318i 318is 325e 325es 325i 325is 325ic M3
1992-1999 E36 BMW 318i 318is 318ic 323is 323ic 325i 325is 325ic
1999-2006 E46 BMW 323i 323ci 325i 325ci
1982-1988 E28 BMW 528e 533i 535i 535is M5
1989-1995 E34 BMW 525i 535i M5

Shifter slop is a common complaint among all BMW models. Some of that play comes from the bushings where the shifter carrier mounts to the transmission. The original rubber carrier bushings don't last very long and when they get too soft the shifter flops around. These Teflon bushings are not as stiff as Delrin so they won't transmit as much vibration and buzz in the shifter. Yet Teflon will last much longer than the factory rubber, giving you precise shifting for many years.

Note: this is only one part of the shift linkage and there may be other components that need replacing to improve shifting feel.

We advise getting a replacement bushing carrier pin as well. If the original rubber bushings are worn the pin will have wear too and you will still have slop in the shifter, even with the new bushings.

These are the OVAL shifter carrier bushings (some BMW models have round bushings).

This item fits the following BMWs:
1992-1998 E36 BMW 328i 328is 328ic M3
1999-2002 E46 BMW 328i 328ci 330i 330ci
2001-2006 E46 BMW M3
1997-2003 E39 BMW 540i M5
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Roadster
1999-2003 E52 BMW Z8