Please ensure your correct model is selected
The B16 PSS9 coilovers offer a stiffer spring rate than stock and a lower ride height for less bodyroll and better handling. These are among the easiest coil over kits on the market - no special mounts required (works with stock mounts and sway bar links), larger adjustment knob allows for easy shock damping changes, and coil over spanner wrenches included for easy height changes. Bilstein backs up their technology with a limited lifetime warranty. TUV approved for fitment, safety, and quality!
Bilstein's monotube shock dampers in the PSS9 offer 9 precise settings for compression and rebound. A new setting is just a click away, allowing you to set a ride and handling combination that works for your setting. Instead of offering too many shock settings that you're never going to use, Bilstein has chosen ten optimal damping curves from a smooth street setting (P9) to an ultra-stiff track-only setup (P1). Shock changes are made from an easy-to-use over-sized adjuster knob.
Ride height adjustments are done from perches that ride on each shock body, which are zinc coated for excellent wear and corrosion resistance. You can set the ride height between 0.5 to 1.3 inches lower than stock ride height. Springs are progressively rated so their initial compression rating is quite soft and then becomes stiffer as the spring compresses. These are stiffer than most coil over kit manufacturers and the results of Bilstein's extensive testing on the German Nurgburgring and Autobahn.
The fitment of these is just like a standard shock and spring package. The front struts and rear shocks are compatible with the stock strut and shock mounts. You can re-use your own or choose a mount with additional features. Because the Bilstein design keeps the sway bar tab in the original location, you can re-use the stock sway bar links. Using the stock mounts keeps the cost and complexity down and allows for TUV certification. You can also be assured of the stock mount's quiet and long-lasting performance. The assembly of the front strut is the same as a the factory strut. In the rear, ride height is made by an adjustable spring perch that sits under the rear spring. Install instructions and diagrams included.
If you're looking for a supremely capable and high quality suspension, then look no further than the Bilstein PSS9. It combines all of the best German engineering with real-world development, and a lifetime warranty.
Fitment note: this system works only on cars not equipped with the factory EDC electronically adjustable shocks.
Featuring:
This item fits the following BMWs:
1995 E36 BMW M3
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
If you are looking for a wider range of camber adjustability in the rear of you car, the IRP Adjustable rear lower control arm is exactly what you need! Built to be much stronger than stock, these rear control arms feature inner monoball bushings and are built of steel, reducing the weight as well. These are perfect for a lowered car or for a track car that needs a greater level of rear adjustment.
Features:
This item fits the following BMWs:
1992-1999 E36 BMW 318i 318is 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2006 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe
Looking to stiffen up your rear shock mount without going for a solid rear mount? The Polyurethane Rear Performance Strut Mount from IRP will give you the stiffer reinforcement without giving you the typical noise, vibration, and harshness that come with traditional performance strut mounts. The polyurethane also helps with preventing rear shock blowouts, a common problem for stock BMW rear mounts that are paired with stiffer than stock suspension.
The bearing sleeve and poly bushing are built to work with all stock style shocks such as Bilstein and H&R coilover and suspension kits.
Fits the following BMW chassis:
E36 BMW All Submodels except for 318ti
E46 BMW All Submodels
E30 BMW All Submodels
E36 Z3 BMW All Submodels
E85/E86 Z4 BMW All Submodels
Control arm bushings play a key role in connecting the wheels to the chassis of the vehicle. Tasked with keeping suspension geometry in check while absorbing noise, vibration, and harshness (NVH) factory rubber bushings were engineered to provide a balance of comfort and control. As a factory bushing ages, it becomes brittle and begins to harden. When this happens the bushing will actually shrink and allow excess play in the suspension joint. This is typically felt by a sudden jerk forward after the car comes to a stop and is a leading cause of "sloppy" or "loose" suspension feel. By replacing the bushing with a full polyurethane unit or using a bushing insert, this play is eliminated since the suspension joint is being supported by a much stiffer material that will not harden or shrink over time. Additionally, the inherent stiffness of the urethane material translates body forces much more directly. This means steering inputs from the driver are effectively transferred to the wheels and vital road information is transmitted properly from the wheels to the driver.
Powerflex street bushings are ideal for street driven vehicles and those that see occasional autocross or track time. Engineered to perform, Powerflex performance polyurethane control arm bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.
Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers.
Sway bars transmit cornering forces from the outside wheels to the inside wheels, helping to keep the vehicle flat during cornering. This in turn reduces body roll and improves the driver's cornering confidence. OEM rubber sway bar bushings are designed with comfort in mind, allowing the sway bar to articulate while permitting additional movement, leading to less-than-ideal bar retention and causes unnecessary body roll.
Powerflex polyurethane sway bar bushings are firmer than factory rubber bushings, reducing body roll and keeping sway bars in check. Polyurethane bushings won't slop around like OEM bushings, allowing sway bars to function at their fullest potential.
Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
Sway bars transmit cornering forces from the outside wheels to the inside wheels, helping to keep the vehicle flat during cornering. This in turn reduces body roll and improves the driver's cornering confidence. OEM rubber sway bar bushings are designed with comfort in mind, allowing the sway bar to articulate while permitting additional movement, leading to less-than-ideal bar retention and causes unnecessary body roll.
Powerflex polyurethane sway bar bushings are firmer than factory rubber bushings, reducing body roll and keeping sway bars in check. Polyurethane bushings won't slop around like OEM bushings, allowing sway bars to function at their fullest potential.
Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
Bilstein has teamed up with Eibach to offer matched shock and spring packages. These Eibach springs are mated to a special set of Bilstein shocks to deliver a sporty and taut ride with as little impact on ride comfort as possible.
The Pro Kit uses an Eibach Pro Kit spring with Bilstein's Sport shocks and struts. Instead of taking parts from different manufacturers, Bilstein has tested the performance of the Eibach spring and tailored their shocks to be a true match for the new spring rate and ride height. This is known as a matched shock and spring and very few tuning companies take these extra steps. Eibach springs tend to be softer overall than most other aftermarket springs, which ensures the ride stays close to a stock comfort while still giving you a lowered stance and improved handling.
Bilstein B12 Features:
Most cars don't need coil overs to improve their handling and bodyroll. For most drivers, simply replacing the shocks and springs with performance versions will meet their goals. If your shocks need replacing, and you felt the handling could be improved a little bit, this is an excellent performance suspension for you.
This item fits the following BMWs:
1996-1999 E36 BMW M3 Coupe, M3 Sedan
The adjustable rear control arm provides on-car rear camber adjustment, from +1 to -3, in order to get the perfect stance and alignment you are looking for. This control arm includes polyurethane bushings that are great for both the track and street use with taking away from comfort and bushing lifespan like many spherical joints.
Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers.
This product was last offered at the strikethrough price on
08-25-2026
This product was last offered at the strikethrough price on
08-25-2026
**For vehicles with stock style springs**
When looking to dial in your steering geometry and alignment for reduced tire where and/or better track handling, the stock suspension is quite limited. To fix this, you can install Camber/Caster plates such as these plates from IRP. Camber/Caster plates allow for adjustment of the top position of the shock's mounting position. These slight adjustments have a huge impact on the stance of the of the wheel when driving straight down the road and when turning into a corner. With simple adjustments, you can increase the grip of the tires in hard turns, improve tread life, or even just make an alignment correction for a vehicle with a lowered ride height.
The IRP Camber Caster plates are made of an aircraft grade aluminum body, for strength and low weight, with an adjustable mounting plate that utilizes a steel monoball mounting point. This makes the plate resistant to corrosion and prevents deformation even with the stiffest shocks and springs.
Features:
Fits the following BMWs:
1991-1999 E36 BMW
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
A strut tower brace adds additional reinforcement to the front strut towers, tying them together for extra rigidity. This makes the whole structure stronger with less chassis flex. Handling and steering feel are improved with better turn-in and input with no downsides. The Dinan strut tower brace is a very high quality aluminum brace with precision machined ends that match the contours of the strut tower. Other braces simply sit on top which reduces their effectiveness. This is definitely one of the stronger strut brace designs on the market. The center bar is polished aluminum with carbon fiber inlays - an unmistakable sign of precise engineering when you open the hood.
For over 35 years, Dinan has been America's premier tuning company, pioneering advancements in BMW modification while retaining a focus on balanced performance that preserves the original character and driving feel that a BMW offers. When you install a Dinan part on your car, know that it's not only carefully developed and tested, but that Dinan stands behind it with a four year, 50,000-mile warranty. Dinan believes so fully in their “total package” approach that once your car has been fitted with enough of their parts, they celebrate your conversion from stock to Dinan with an exclusive trunk badge, displayed proudly by BMW enthusiasts everywhere. This part is worth 2 points towards your Dinan badge.
Fitment Note: fits 1992-1995 E36 325i with and without ASC traction control
This item fits the following BMWs:
1992-1999 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1997-2000 Z3 BMW Z3 2.3 Z3 2.8 M Coupe M Roadster
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
Tasked with keeping the vehicles rear end firmly mounted while absorbing noise, vibration, and harshness (NVH) factory rubber subframe bushings were engineered to provide a balance of control while keeping the ride quality soft and supple. As a factory bushings age, they become brittle and begin to harden. When this happens the bushing will actually shrink and allow excess play, or movement in the subframe. This is typically felt by a sudden jerk or "thunking" noise under acceleration and is a leading cause of "sloppy" or "loose" suspension feel. By replacing the bushings with full polyurethane this play is eliminated since the subframe is being held in place by a much stiffer material that will not harden or shrink over time. Additionally, the inherent stiffness of the urethane material translates body forces much more directly. This means steering and acceleration inputs from the driver are effectively transferred to the wheels and vital road information is transmitted properly from the wheels to the driver.
Powerflex street bushings are ideal for street driven vehicles and those that see occasional autocross or track time. Need bushings for a dedicated track car? Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.
Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers.
NOTE: Will not fit 318ti
**For vehicles with coilover front suspension**
When looking to dial in your steering geometry and alignment for reduced tire where and/or better track handling, the stock suspension is quite limited. To fix this, you can install Camber/Caster plates such as these plates from IRP. Camber/Caster plates allow for adjustment of the top position of the shock's mounting position. These slight adjustments have a huge impact on the stance of the of the wheel when driving straight down the road and when turning into a corner. With simple adjustments, you can increase the grip of the tires in hard turns, improve tread life, or even just make an alignment correction for a vehicle with a lowered ride height.
The IRP Camber Caster plates are made of an aircraft grade aluminum body, for strength and low weight, with an adjustable mounting plate that utilizes a steel monoball mounting point. This makes the plate resistant to corrosion and prevents deformation even with the stiffest shocks and springs.
Features:
Fits the following BMWs:
1991-1999 E36 BMW
Tasked with keeping the vehicles rear end firmly mounted while absorbing noise, vibration, and harshness (NVH) factory rubber subframe bushings were engineered to provide a balance of control while keeping the ride quality soft and supple. As a factory bushings age, they become brittle and begin to harden. When this happens the bushing will actually shrink and allow excess play, or movement in the subframe. This is typically felt by a sudden jerk or "thunking" noise under acceleration and is a leading cause of "sloppy" or "loose" suspension feel. By replacing the bushings with full polyurethane this play is eliminated since the subframe is being held in place by a much stiffer material that will not harden or shrink over time. Additionally, the inherent stiffness of the urethane material translates body forces much more directly. This means steering and acceleration inputs from the driver are effectively transferred to the wheels and vital road information is transmitted properly from the wheels to the driver.
Powerflex street bushings are ideal for street driven vehicles and those that see occasional autocross or track time. Need bushings for a dedicated track car? Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.
Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers.
Rear shock mounts are tasked with securing shocks while absorbing noise, vibration and harshness that would otherwise be associated with a solid mount. Factory rubber bushings are a compromise between a cushy ride and responsive handling.
Powerflex polyurethane rear shock mounts are firmer than OEM bushings, resulting in better handling, a more responsive rear-end, and more efficient suspension articulation - all with minimal sacrifice to ride quality.
Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers.
This product was last offered at the strikethrough price on
03-17-2026
This product was last offered at the strikethrough price on
03-17-2026
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
Control arm bushings play a key role in connecting the wheels to the chassis of the vehicle. Tasked with keeping suspension geometry in check while absorbing noise, vibration, and harshness (NVH) factory rubber bushings were engineered to provide a balance of comfort and control. As a factory bushing ages, it becomes brittle and begins to harden. When this happens the bushing will actually shrink and allow excess play in the suspension joint. This is typically felt by a sudden jerk forward after the car comes to a stop and is a leading cause of "sloppy" or "loose" suspension feel. By replacing the bushing with a full polyurethane unit or using a bushing insert, this play is eliminated since the suspension joint is being supported by a much stiffer material that will not harden or shrink over time. Additionally, the inherent stiffness of the urethane material translates body forces much more directly. This means steering inputs from the driver are effectively transferred to the wheels and vital road information is transmitted properly from the wheels to the driver.
Powerflex street bushings are ideal for street driven vehicles and those that see occasional autocross or track time. Need bushings for a dedicated track car? Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane control arm bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.
Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers.
These SPL parts adjustable rear camber arms replace OEM part number 33326770813
SPL Parts is a performance suspension manufacturer that designs and tests their products all in-house here in the USA. Additionally, all materials used are sourced from American suppliers to ensure consistently high quality products. SPL Parts products are all constructed using 6061-T6 aluminum tubing, DOM mandrel bent tubing, and 6061 and 2024 aluminum for high strength and quality. All TIG welding and CNC machining is also done locally by professional welders and machine shops to meet exact quality standards and tolerance specifications. For anything from racing to street driven needs, SPL Parts offer an amazing line of premium quality products that are perfect to get your car back in spec.
These rear camber arms allow for significantly greater camber adjustment over stock, a major benefit to lowered cars that need their camber readjusted to prevent tire wear and poor handling. These camber arms also provide increased stability and predictability versus the stock camber arms with rubber bushings.
Technical Specifications:
Fits the following BMWs:
1992-1999 E36 BMW All Submodels
1999-2006 E46 BMW RWD Models
Differential bushings are responsible for keeping the differential in solid alignment while dampening drivetrain vibration. While OE rubber bushings are fine when they are new from the factory, aged and worn out rubber bushings create a multitude of issues that can range from annoying to dangerous. As a factory bushing ages, it begins to harden and become brittle. When this happens the bushing will actually shrink and allow for movement at the differential mounting point. At this point, the differential is free to shift under load causing a noticeable clunking noise under acceleration and deceleration and massively increasing the stress on the driveshaft and axles. Manual transmissions suffer the worst from this as it can make shifting difficult since the differential will shift when the clutch is engaged and disengaged.
By replacing these bushings with full polyurethane, the movement is eliminated since the mounting point is supported by a much stiffer material that will not harden or shrink over time. This means less stress on the driveshaft and axles and greater longevity of supporting components.
Engineered to perform, Powerflex performance polyurethane differential bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved acceleration response, more direct shifting feel and overall improved drivetrain composure with Powerflex performance polyurethane bushings.
Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers.
Powerflex Handling Packs contain bushings that have been specifically selected to give the perfect combination of value versus performance.
We have chosen products from our range to maximize the performance of the suspension, while being mindful of cost with a price savings over buying the parts individually.
This can be an ideal upgrade complementing other suspension upgrades such as shock absorbers and springs.
Includes a Powerflex keyring and sticker.
Powerflex offers improved reliability over original parts and of course carries our Lifetime Warranty.
Includes:
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.
A strut tower brace adds additional reinforcement to the front strut towers, tying them together for extra rigidity. This makes the whole structure stronger with less chassis flex. Handling and steering feel are improved with better turn-in and input with no downsides.
The IRP adjustable strut brace bar is a high quality brace that is constructed of 100% steel for guaranteed reinforcement and prevention of flex. The brace bar is painted black to ensure corrosion protection.
Easily installed with basic hand tools.
*Does not fit convertible chassis"
Fits the following BMW chassis:
E36 BMW All Submodels
This product was last offered at the strikethrough price on
07-29-2026
The Bilstein B8 Performance Plus Kit includes two front struts and two rear shocks. These shocks are for use with lowered springs such as from H&R or Eibach. We do not recommend that you use them with any factory spring, including factory sport package springs. With the increased damping rates from stock you will have much more control over body motions. These will give a much more buttoned down and taut feeling with lowering springs compared to stock shocks.
These shocks fit the following BMWs:
1994-1999 E36 M3, M3 Convertible
The B16 PSS9 coilovers offer a stiffer spring rate than stock and a lower ride height for less bodyroll and better handling. These are among the easiest coil over kits on the market - no special mounts required (works with stock mounts and sway bar links), larger adjustment knob allows for easy shock damping changes, and coil over spanner wrenches included for easy height changes. Bilstein backs up their technology with a limited lifetime warranty. TUV approved for fitment, safety, and quality!
Bilstein's monotube shock dampers in the PSS9 offer 9 precise settings for compression and rebound. A new setting is just a click away, allowing you to set a ride and handling combination that works for your setting. Instead of offering too many shock settings that you're never going to use, Bilstein has chosen ten optimal damping curves from a smooth street setting (P9) to an ultra-stiff track-only setup (P1). Shock changes are made from an easy-to-use over-sized adjuster knob.
Ride height adjustments are done from perches that ride on each shock body, which are zinc coated for excellent wear and corrosion resistance. You can set the ride height between 0.5 to 1.3 inches lower than stock ride height. Springs are progressively rated so their initial compression rating is quite soft and then becomes stiffer as the spring compresses. These are stiffer than most coil over kit manufacturers and the results of Bilstein's extensive testing on the German Nurgburgring and Autobahn.
The fitment of these is just like a standard shock and spring package. The front struts and rear shocks are compatible with the stock strut and shock mounts. You can re-use your own or choose a mount with additional features. Because the Bilstein design keeps the sway bar tab in the original location, you can re-use the stock sway bar links. Using the stock mounts keeps the cost and complexity down and allows for TUV certification. You can also be assured of the stock mount's quiet and long-lasting performance. The assembly of the front strut is the same as a the factory strut. In the rear, ride height is made by an adjustable spring perch that sits under the rear spring. Install instructions and diagrams included.
If you're looking for a supremely capable and high quality suspension, then look no further than the Bilstein PSS9. It combines all of the best German engineering with real-world development, and a lifetime warranty.
Fitment note: this system works only on cars not equipped with the factory EDC electronically adjustable shocks.
Featuring:
Fits the Following Vehicles:
1996-1999 BMW E36 M3
Tasked with keeping the vehicles rear end firmly mounted while absorbing noise, vibration, and harshness (NVH) factory rubber subframe bushings were engineered to provide a balance of control while keeping the ride quality soft and supple. As a factory bushings age, they become brittle and begin to harden. When this happens the bushing will actually shrink and allow excess play, or movement in the subframe. This is typically felt by a sudden jerk or "thunking" noise under acceleration and is a leading cause of "sloppy" or "loose" suspension feel. By replacing the bushings with full polyurethane this play is eliminated since the subframe is being held in place by a much stiffer material that will not harden or shrink over time. Additionally, the inherent stiffness of the urethane material translates body forces much more directly. This means steering and acceleration inputs from the driver are effectively transferred to the wheels and vital road information is transmitted properly from the wheels to the driver.
Powerflex street bushings are ideal for street driven vehicles and those that see occasional autocross or track time. Need bushings for a dedicated track car? Engineered to perform, Powerflex performance polyurethane bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.
Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers.
Tasked with keeping the vehicles rear end firmly mounted while absorbing noise, vibration, and harshness (NVH) factory rubber subframe bushings were engineered to provide a balance of control while keeping the ride quality soft and supple. As a factory bushings age, they become brittle and begin to harden. When this happens the bushing will actually shrink and allow excess play, or movement in the subframe. This is typically felt by a sudden jerk or "thunking" noise under acceleration and is a leading cause of "sloppy" or "loose" suspension feel. By replacing the bushings with full polyurethane this play is eliminated since the subframe is being held in place by a much stiffer material that will not harden or shrink over time. Additionally, the inherent stiffness of the urethane material translates body forces much more directly. This means steering and acceleration inputs from the driver are effectively transferred to the wheels and vital road information is transmitted properly from the wheels to the driver.
Powerflex street bushings are ideal for street driven vehicles and those that see occasional autocross or track time. Need bushings for a dedicated track car? Engineered to perform, Powerflex performance polyurethane bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.
Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers.
Sway bars transmit cornering forces from the outside wheels to the inside wheels, helping to keep the vehicle flat during cornering. This in turn reduces body roll and improves the driver's cornering confidence. OEM rubber sway bar bushings are designed with comfort in mind, allowing the sway bar to articulate while permitting additional movement, leading to less-than-ideal bar retention and causes unnecessary body roll.
Powerflex polyurethane sway bar bushings are firmer than factory rubber bushings, reducing body roll and keeping sway bars in check. Polyurethane bushings won't slop around like OEM bushings, allowing sway bars to function at their fullest potential.
Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers.
This product was last offered at the strikethrough price on
07-29-2026
Rally Road Productions, Inc. is a team supported by a group of people with great abilities in their area of expertise. From the "web guy" and driving instructor friends, to owners of various machine shops, they have surrounded ourselves with people that can be trusted to create and manufacture quality products. This is the key to ensuring everything that they sell will perform as it was intended. The goal is to increase customer satisfaction and make the customization or performance enhancement of your vehicle a more enjoyable venture.
Have you ever snapped a transmission brace under full throttle? NOT a fun experience. For that reason, Rally Road has come up with the very last transmission brace your E36 will ever need.
Back when the minds at BMW set out to design the E36's lower transmission support, they executed perfectly. A cast piece manufactured from lightweight aluminum would surely provide the proper support for the business end of the powertrain. This part functioned fine...mostly...when the vehicle was driven modestly. However, push it too hard and this brace becomes perfectly unusable when it snaps in half.
This upgraded piece is manufactured out of solid steel. Laser cut, precision CNC bent, and then tig welded together - this thing is ready to take a beating. Finish it off with a flawless black powder coat and what you have is a transmission brace that is as beautiful as it is bulletproof. Whether you're considering this as an alternative to an already broken piece or just shopping for your next mod, this is a must-have for ANY E36 owner.
This product was last offered at the strikethrough price on
04-09-2026
This kit is contains all new strut and shock mounts and hardware needed when installing a aftermarket suspension on your vehicle.
Fits the following BMW's
1995 BMW E36 M3 S50
This product was last offered at the strikethrough price on
05-03-2026
This product was last offered at the strikethrough price on
05-03-2026
This product was last offered at the strikethrough price on
08-04-2026
This product was last offered at the strikethrough price on
08-04-2026
This strut and shock mount package covers the front and rear rubber mounts and bushings commonly replaced during a strut and shock install. While you're installing new front struts and rear shocks these are easily installed - there's no additional labor and special tools are not required. Since these pieces are mostly rubber, they dry up and crack over time. Re-using them lead to problems with fitment or noise, and may have safety issues as well. These mounts and pads are the perfect complement to your new shocks to help restore your car's handling and performance.
We sell the basic strut and shock mount package, which includes:
In addition, you can add the front spring pads, front bump stops, front dust boots, rear bump stops, and rear dust boots if needed. But please note that some shocks and coil overs come with all or some of these pieces already. If in doubt, check with your supplier on what is included.
We offer three varieties of the rear shock mounts - OEM, Repair Shop, and HP alum-rubber. We recommend either the Repair Shop or HP mounts because the stock OEM design has a flaw that can lead to premature failure of the mounts. The Repair Shop and HP mounts use a different design that will last longer and the Repair Shop mounts also have a lifetime warranty!
This item fits the following BMWs:
1996-1999 E36 BMW M3
1996-2002 Z3 BMW 2.5 2.5i 2.8 3.0i M Coupe
This product was last offered at the strikethrough price on
08-14-2026
This product was last offered at the strikethrough price on
08-14-2026
This kit is contains all new strut and shock mounts and hardware needed when installing a aftermarket suspension on your vehicle.
Fits the following BMW's
1996-1999 BMW M3
A strut tower brace adds additional reinforcement to the front strut towers, tying them together for extra rigidity. This makes the whole structure stronger with less chassis flex. Handling and steering feel are improved with better turn-in and input with no downsides.
The IRP adjustable strut brace bar is a high quality brace that is constructed of 100% steel for guaranteed reinforcement and prevention of flex. The brace bar is painted black to ensure corrosion protection and to add to the looks of the engine bay.
Easily installed with basic hand tools.
Fits the following BMW chassis:
E36 BMW All Submodels
Want the best performance option in shock tower mounts? IRP has created their pillow-ball rear shock mounts for just this need. These rear shock mounts are designed for use on the track and racing. This set of mounts will help your rear shocks perform the best they can in all conditions. The advantage to using a mount with spherical bearing is that it allows the shock to freely move off axis without side loading the shock shaft like rubber or polyurethane mounts do. Side loading a shock increases stiction and wear which decreases its efficiency. Because these are mounts without an isolator (rubber or polyurethane) to dampen road noise and vibrations we do not recommend them for street cars.
The bearing sleeve and poly bushing are built to work with all stock style shocks such as Bilstein and H&R coilover and suspension kits.
Fits the following BMW chassis:
E36 BMW All Submodels except for 318ti
E46 BMW All Submodels
E30 BMW All Submodels
E36 Z3 BMW All Submodels
E85/E86 Z4 BMW All Submodels
