BMW Suspension Parts for BMW E36 (1992-1998) M3

If you are looking for a wider range of camber adjustability in the rear of you car, the IRP Adjustable rear lower control arm is exactly what you need! Built to be much stronger than stock, these rear control arms feature inner monoball bushings and are built of steel, reducing the weight as well. These are perfect for a lowered car or for a track car that needs a greater level of rear adjustment.

Features:

• Strong Steel Construction
• Adjustable
• Painted Yellow For Corrosion Protection
• Weight Reduction
• Monoball Inner Mount

This item fits the following BMWs:
1992-1999 E36 BMW 318i 318is 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2006 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe

Looking to stiffen up your rear shock mount without going for a solid rear mount? The Polyurethane Rear Performance Strut Mount from IRP will give you the stiffer reinforcement without giving you the typical noise, vibration, and harshness that come with traditional performance strut mounts. The polyurethane also helps with preventing rear shock blowouts, a common problem for stock BMW rear mounts that are paired with stiffer than stock suspension. 

The bearing sleeve and poly bushing are built to work with all stock style shocks such as Bilstein and H&R coilover and suspension kits.

Fits the following BMW chassis:
E36 BMW All Submodels except for 318ti
E46 BMW All Submodels
E30 BMW All Submodels
E36 Z3 BMW All Submodels
E85/E86 Z4 BMW All Submodels

**For vehicles with coilover front suspension**

When looking to dial in your steering geometry and alignment for reduced tire where and/or better track handling, the stock suspension is quite limited. To fix this, you can install Camber/Caster plates such as these plates from IRP. Camber/Caster plates allow for adjustment of the top position of the shock's mounting position. These slight adjustments have a huge impact on the stance of the of the wheel when driving straight down the road and when turning into a corner. With simple adjustments, you can increase the grip of the tires in hard turns, improve tread life, or even just make an alignment correction for a vehicle with a lowered ride height. 

The IRP Camber Caster plates are made of an aircraft grade aluminum body, for strength and low weight, with an adjustable mounting plate that utilizes a steel monoball mounting point. This makes the plate resistant to corrosion and prevents deformation even with the stiffest shocks and springs.

Features:

• Decreased understeer
• Decreases outside edge tire wear
• Aircraft Grade Aluminum Construction
• Steel Monoball and Mounting Sleeves

Fits the following BMWs:
1991-1999 E36 BMW

A strut tower brace adds additional reinforcement to the front strut towers, tying them together for extra rigidity. This makes the whole structure stronger with less chassis flex. Handling and steering feel are improved with better turn-in and input with no downsides. 

The IRP adjustable strut brace bar is a high quality brace that is constructed of 100% steel for guaranteed reinforcement and prevention of flex. The brace bar is painted black to ensure corrosion protection.

Easily installed with basic hand tools.

*Does not fit convertible chassis"

Fits the following BMW chassis:
E36 BMW All Submodels

Looking to upgrade your front suspension to increase the strength and your steering angle for the track? IRP has you covered with their BMW Lock Kit. This kit includes new control arms that are stronger than stock and have monoball ball joints, new tie rod ends that feature steel monoball ball joints as well, new offset control arm bushings, fully adjustable camber plates, roll center/bump steer correction plates, and all new hardware. This enables this kit to be fully plug and play, giving you a much more adjustable front suspension, and increases the total amount of steering angle up to 65 degrees.

This kit is perfect for those looking to build a drift car and ensure their suspension is ready to take on the challenge.

Kit features:

• CNC Laser Cut Components
• Plug & Play - includes all needed hardware
• Increase to 65 Degree (or more) steering angle
• Includes Camber Plates
• Stiffer offset control arm bushings
• Roll Center and Bump Steer Correction Plates
• High strength control arms with steel monoball ball joints
• Increased length steering tie rods with steel monoball ball joints
• DriftAllstar- & EEDC-Tested
• Total weight of all components included: 13.5 kg / 29.8 lbs

Fits the following BMWs:
1992-1999 E36 BMW All Submodels