BMW Suspension Parts for BMW 5 Series E39 (1996-2003)

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E36, E39 ...

For vehicles with a production date 1996-1997

T#:389645

Part#: 192416-1J

In Stock

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC)
2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i
2004-2011 E63 E64 BMW 645ci 650i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003 E52 BMW Z8 Roadster (without EDC)

Show More Show Less

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E39 540/M...

For models with a 10/1997+ production date

T#:389661

Part#: 193616-1J

Ships on Sep 28, 2026

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
1997-2003 E39 BMW 525i 528i 530i 540i (for cars with EDC)
1999-2003 E39 BMW M5
1995-2001 E38 BMW 740i 740il 750il (for cars with EDC)

Show More Show Less

Eibach Pro-Kit Spring Set - E39 525/528/530i (w/o Self Leveling) ...

For sedan models only without self leveling suspension

T#:376268

Part#: 2053.140

Back Ordered

10% off MSRP $ 438.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 395.00 USD

Add to Wish List

Qty

10% off MSRP

$ 438.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 395.00 USD

Add to Wish List

Looking to lower your BMW for a sportier appearance and improved cornering, performance, and aerodynamics? This spring kit from Eibach is a perfect solution to lower the ride height without compromising the ride quality of your BMW.

With this kit, you can expect an average lowering of:

Front - 1.3-1.5"
Rear - 1"

Show More Show Less

Strut Brace, Front, BMW 5 Series 540i 1997-2003

T#:394521

Part#: 1969939012

Ships in 5 Business Days

$ 245.00 USD

Add to Wish List

Qty

$ 245.00 USD

Add to Wish List

Racing Dynamics has been a huge part of the European community since the early 80's. Their sway bars and strut braces are developed from pure professional experience, utilizing the expertise of skilled race engineers to develop or improve products to meet the demands of BMW drivers. The dedicated focus on performance, comfort, and strength are what make Racing Dynamics products the best on the market no matter if it's street or track.

Show More Show Less

KMAC Stage 2 Street/Track Front Adjustable Camber/Caster Plates - E39...

T#:389317

Part#: 193616-2L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Street/Track, Stage 2
Bearing: PTFE-lined pillow-ball with thin polyurethane bushing

The Stage 2 KMAC plates are a mixed street/track camber/caster plate meant to be used in a variety of suspensions. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions. Bearing inserts and adapters included. The Stage 2 camber plates are shorter than a factory mount so may not be suitable for cars will little suspension travel. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

KMAC Stage 3 Track Front Adjustable Camber/Caster Plates - E39 540/M5...

T#:389662

Part#: 193616-3L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Track, Stage 3
Bearing: PTFE-lined pillow-ball, no bushing

KMAC Stage 3 camber/caster plates are designed for track or race-only situations where comfort and noise are not the primary concerns. The Stage 3 camber plates use a pillowball bearing, solidly mounted within the camber plate for direct alignment of the strut shaft and no excess play or deflection. Stage 3 are designed to increase negative camber with their patented 'floating' adjustment that changes camber and caster together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Fitment is limited to race-only small diameter coil-over springs (not stock-type). Bearing inserts and adapters included. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
1997-2003 E39 BMW 525i 528i 530i 540i (for cars with EDC)
1999-2003 E39 BMW M5
1995-2001 E38 BMW 740i 740il 750il (for cars with EDC)
2004-2010 E60 BMW M5
2004-2011 E63 BMW M6

Show More Show Less

KMAC Stage 3 Street/Track Front Adjustable Camber/Caster Plates - E36...

For models up to 09/1997

T#:389646

Part#: 192416-3L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Street/Track, Stage 2
Bearings: main PTFE-lined pillow-ball bearing suspended in polyurethane; self-lubricating radial axial bearing/bushing in upper spring plate
Springs: includes OEM size upper spring perch, 60mm upper spring perch, and 2.5" upper spring perch

The Stage 3 KMAC plates are a mixed track and street camber/caster plate meant to be used in a variety of suspensions and setups. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions and upper spring perches are included for OEM springs, 60mm, and 2.5" coil over springs. The upper perch assembly incorporate a self-sliding radial bushing that allows the spring to spin during its travel instead of bind. This reduces tension on the spring and helps reduce noise and spring 'popping' noises. Bearing inserts, spacers for correct articulating angles, and 3 sizes of upper nut adapters included. The urethane bushings and bearings are replaceable if they wear out. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Basic instructions included but professional installation is required.

Note: suspensions vary from manufacturer to manufacturer. The proper stacked height and clearances are required. K-Mac includes bearing adapters, spacers, and various top nuts but it is still the responsibility of the installer to ensure a correct and safe fitment. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC)
2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i
2004-2011 E63 E64 BMW 645ci 650i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003 E52 BMW Z8 Roadster (without EDC)

Show More Show Less

KMAC Stage 2 Street/Track Front Adjustable Camber/Caster Plates - E36...

T#:389647

Part#: 192416-2L

Ships on Sep 18, 2026

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Street/Track, Stage 2
Bearings: main PTFE-lined pillow-ball bearing suspended in polyurethane; self-lubricating radial axial bearing/bushing in upper spring plate
Springs: includes OEM size upper spring perch, 60mm upper spring perch, and 2.5" upper spring perch

The Stage 2 KMAC plates are a mixed track and street camber/caster plate meant to be used in a variety of suspensions and setups. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions and upper spring perches are included for OEM springs, 60mm, and 2.5" coil over springs. The upper perch assembly incorporate a self-sliding radial bushing that allows the spring to spin during its travel instead of bind. This reduces tension on the spring and helps reduce noise and spring 'popping' noises. Bearing inserts, spacers for correct articulating angles, and 3 sizes of upper nut adapters included. The urethane bushings and bearings are replaceable if they wear out. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Basic instructions included but professional installation is required.

Note: suspensions vary from manufacturer to manufacturer. The proper stacked height and clearances are required. K-Mac includes bearing adapters, spacers, and various top nuts but it is still the responsibility of the installer to ensure a correct and safe fitment. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC)
2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i
2004-2011 E63 E64 BMW 645ci 650i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003 E52 BMW Z8 Roadster (without EDC)

Show More Show Less

KMAC Street Rear Inner Adjustable Camber/Toe Bushings - E39 M5 ...

T#:389669

Part#: 194026J

Special Order: No Guaranteed ETA

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Perfect for lowered cars that need to dial out negative camber to preserve tires. Also perfect for track cars - easily dial in toe and camber for the track for better handling. Priced per set.

This item fits the following BMWs:
1998-2004 E39 BMW M5

Show More Show Less

Bav Auto Shock and Strut Nut Tool

10X Entries Into Our F80 M3 Sweepstakes

T#:580394

Part#: B8800081

In Stock

Sale - Save 5% $ 123.99

This product was last offered at the strikethrough price on
05-03-2026

$ 117.79 USD

Add to Wish List

Qty

Sale - Save 5%

$ 123.99

This product was last offered at the strikethrough price on
05-03-2026

$ 117.79 USD

Add to Wish List

Used to install or remove shock and strut nuts - no more using an impact gun!

Bav Auto Scissor Type Ball Joint / Tie Rod Separator

10X Entries Into Our F80 M3 Sweepstakes

T#:580366

Part#: B8800042

Ships on Feb 2, 2027

Sale - Save 15% $ 46.99

This product was last offered at the strikethrough price on
05-03-2026

$ 39.94 USD

Add to Wish List

Qty

Sale - Save 15%

$ 46.99

This product was last offered at the strikethrough price on
05-03-2026

$ 39.94 USD

Add to Wish List

Use this tool to separate control arm ball-joints and larger tie-rod end joints. This tool is particularly beneficial when dealing with tight locations that prevent the use of non-scissor separator tools. Note that max jaw opening is 1 3/4".

Show More Show Less

Bav Auto Trailing Arm Inner Bushing Tool - Master Set

10X Entries Into Our F80 M3 Sweepstakes
Be sure to add some grease to the rods in this tool set during installation to prevent breakage.

T#:580442

Part#: B8800137

In Stock

Sale - Save 3% $ 293.99

This product was last offered at the strikethrough price on
05-03-2026

$ 285.17 USD

Add to Wish List

Qty

Sale - Save 3%

$ 293.99

This product was last offered at the strikethrough price on
05-03-2026

$ 285.17 USD

Add to Wish List

Remove and install the two rear inner trailing arm / lower control arm bushings that are in the subframe with one tool set without removing the trailing arms from the vehicle. This tool is designed to work with all trailing arm bushing designs on E82, E84, E90 ,E91, E92, E93 model cars. Replaces bushing part #'s 33326770829 and 33326763092.

Show More Show Less

BMW Bav Auto Rear Ball Joint Press

10X Entries Into Our F80 M3 Sweepstakes

T#:580356

Part#: B8800028

In Stock

Sale - Save 3% $ 130.99

This product was last offered at the strikethrough price on
06-10-2026

$ 127.06 USD

Add to Wish List

Qty

Sale - Save 3%

$ 130.99

This product was last offered at the strikethrough price on
06-10-2026

$ 127.06 USD

Add to Wish List

Allows for removal / replacement of lower rear ball joint, enabling you to get this job done at home, saving you time and money on labor.

Bav Auto Upper Spring Compressor Jaw - E39/E46

10X Entries Into Our F80 M3 Sweepstakes

T#:580380

Part#: B8800062

In Stock

Sale - Save 12% $ 72.99

This product was last offered at the strikethrough price on
05-03-2026

$ 64.22 USD

Add to Wish List

Qty

Sale - Save 12%

$ 72.99

This product was last offered at the strikethrough price on
05-03-2026

$ 64.22 USD

Add to Wish List

This upper spring compressor jaw is specifically for E39 and E46 springs, for use with Bav Auto spring compressors.

Bav Auto 9-Way Slide Hammer Puller Set

10X Entries Into Our F80 M3 Sweepstakes

T#:580405

Part#: B8800095

Ships on Sep 29, 2026

Sale - Save 5% $ 104.99

This product was last offered at the strikethrough price on
05-03-2026

$ 99.74 USD

Add to Wish List

Qty

Sale - Save 5%

$ 104.99

This product was last offered at the strikethrough price on
05-03-2026

$ 99.74 USD

Add to Wish List

A complete slide hammer kit for your next suspension job.

Bav Auto Rear Ball Joint Tool

10X Entries Into Our F80 M3 Sweepstakes

T#:580371

Part#: B8800049

Ships on Oct 19, 2026

Sale - Save 5% $ 81.99

This product was last offered at the strikethrough price on
06-10-2026

$ 77.89 USD

Add to Wish List

Qty

Sale - Save 5%

$ 81.99

This product was last offered at the strikethrough price on
06-10-2026

$ 77.89 USD

Add to Wish List

This ball joint press is designed make removal of your old ball joints as painless as possible. Adapts the size of the balljoint and forces it out when using a ratchet.

Control Arm Bushing Remover & Installer - Bavarian Autosport ...

10X Entries Into Our F80 M3 Sweepstakes
Designed for use with 65mm bushings

T#:580391

Part#: B8800078

Ships on Oct 19, 2026

Sale - Save 10% $ 109.99

This product was last offered at the strikethrough price on
05-03-2026

$ 98.99 USD

Add to Wish List

Qty

Sale - Save 10%

$ 109.99

This product was last offered at the strikethrough price on
05-03-2026

$ 98.99 USD

Add to Wish List

Don't struggle with hammers and improper techniques, drive your bushings out easily with this control arm bushing remover and installer.

Bav Auto 23mm Tie Rod Puller

10X Entries Into Our F80 M3 Sweepstakes

T#:580451

Part#: B8800146

In Stock

Sale - Save 40% $ 46.99

This product was last offered at the strikethrough price on
05-03-2026

$ 28.40 USD

Add to Wish List

Qty

Sale - Save 40%

$ 46.99

This product was last offered at the strikethrough price on
05-03-2026

$ 28.40 USD

Add to Wish List

Will not tear tie rod boots, which can lead to premature failure of the tie rod assembly.

Bav Auto Tie-rod and Upper/Lower Control Arm Ball Joint Puller - E39 ...

10X Entries Into Our F80 M3 Sweepstakes

T#:580406

Part#: B8800096

Special Order: No Guaranteed ETA

Sale - Save 10% $ 69.99

This product was last offered at the strikethrough price on
05-03-2026

$ 62.99 USD

Add to Wish List

Qty

Sale - Save 10%

$ 69.99

This product was last offered at the strikethrough price on
05-03-2026

$ 62.99 USD

Add to Wish List

This puller is perfect for removing all tie-rod ends and ball joints on the front suspension of all E39 5 Series cars 1997-2003.

From 1974 to 2019, Bavarian Autosport was one of the premier vendors for BMW and MINI auto parts. We are happy to preserve the Bav Auto legacy by continuing to carry their high-quality products into the future. All Bav Auto parts will remain unchanged in design and sourced from the same OEM suppliers to ensure long-lasting reliability. We trust these parts, accessories, and upgrades so confidently that we back every Bavarian Autosport branded component with a 2-year warranty.

Show More Show Less

Bav Auto Spindle Housing Spreader Tool - 1/2" Drive

10X Entries Into Our F80 M3 Sweepstakes

T#:580424

Part#: B8800117

In Stock

Sale - Save 25% $ 20.99

This product was last offered at the strikethrough price on
05-03-2026

$ 15.74 USD

Add to Wish List

Qty

Sale - Save 25%

$ 20.99

This product was last offered at the strikethrough price on
05-03-2026

$ 15.74 USD

Add to Wish List

Used to separate steering knuckle from your shock/strut easily, no need to use a chisel and hammer now!

16mm / 18mm Thin Wrench - For Use On Swaybar End Links - Bavarian Aut...

10X Entries Into Our F80 M3 Sweepstakes

T#:580331

Part#: B8300001

In Stock

Sale - Save 3% $ 9.99

This product was last offered at the strikethrough price on
05-03-2026

$ 9.65 USD

Add to Wish List

Qty

Sale - Save 3%

$ 9.99

This product was last offered at the strikethrough price on
05-03-2026

$ 9.65 USD

Add to Wish List

Project Cars

SELECT YOUR BMW

BMW Suspension Parts for BMW 5 Series E39 (1996-2003)

Sub-Categories

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E36, E39 ...

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E39 540/M...

Eibach Pro-Kit Spring Set - E39 525/528/530i (w/o Self Leveling) ...

Strut Brace, Front, BMW 5 Series 540i 1997-2003

KMAC Stage 2 Street/Track Front Adjustable Camber/Caster Plates - E39...

KMAC Stage 3 Track Front Adjustable Camber/Caster Plates - E39 540/M5...

KMAC Stage 3 Street/Track Front Adjustable Camber/Caster Plates - E36...

KMAC Stage 2 Street/Track Front Adjustable Camber/Caster Plates - E36...

KMAC Street Rear Inner Adjustable Camber/Toe Bushings - E39 M5 ...

Bav Auto Shock and Strut Nut Tool

Bav Auto Scissor Type Ball Joint / Tie Rod Separator

Bav Auto Trailing Arm Inner Bushing Tool - Master Set

BMW Bav Auto Rear Ball Joint Press

Bav Auto Upper Spring Compressor Jaw - E39/E46

Bav Auto 9-Way Slide Hammer Puller Set

Bav Auto Rear Ball Joint Tool

Control Arm Bushing Remover & Installer - Bavarian Autosport ...

Bav Auto 23mm Tie Rod Puller

Bav Auto Tie-rod and Upper/Lower Control Arm Ball Joint Puller - E39 ...

Bav Auto Spindle Housing Spreader Tool - 1/2" Drive

16mm / 18mm Thin Wrench - For Use On Swaybar End Links - Bavarian Aut...

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results