BMW 5 Series E60 (2004-2010)

This is an OEM INA tensioner pulley, also known as the adjusting pulley and lower pulley. This pulley is mounted on the belt tensioner near the center of the belt assembly. The upper and lower pulleys are known to be the primary sources for 'belt squealing'. This pulley is also encased in rubber which will crack over time. If left without service the rubber could fail completely, chucking the belt and leaving you stranded. Replacement is a very simple procedure and can be done anytime the fan is off the engine (belt replacement, water pump service, alternator replacement, etc).

This pulley is mounted along with the hydraulic belt tensioner but can be replaced on its own. It is used for the main drive belt on the M50-M54 family engines (M50, M50TU, M52, S52, M52TU, M54, M56, and S54 engines). This is the same belt that covers the water pump/alternator/power steering systems. Replacement is a very easy procedure (requires fan removal) and will have your engine purring in no time. Belt replacement is strongly recommended at the same time. If you have a mechanical belt tensioner, the pulley can only be replaced with a new tensioner.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

If you need the hydraulic belt tensioner, click here.

This item is 70mm Diameter. Please check the diameter before ordering.

This tensioner pulley fits the following BMWs:
1991-1995 E34 525i (M50 engine)
1992-1999 E36 325i, 325is, 328i, 328is, 323is
1995-1999 E36 M3 (M3 3.0 & M3 3.2 liter)
1997-2003 E39 525i, 528i, 530i - Only for Hydraulic Tensioner
1999-2000 E46 323i, 323Ci, 328i, 328Ci - Only for Hydraulic Tensioner
2001-2005 E46 325i, 325Ci, 325xi, 330i, 330Ci, 330xi - Only for Hydraulic Tensioner
2001-2006 E46 M3 coupe & convertible - Only for Hydraulic Tensioner
2000-2006 X5 3.0 liter (E53 chassis)
2004 E60 525i, 530i (M54 engine)
1997-2002 Z3 & MZ3 2.5, 2.8, 3.0, M Roadster, M Coupe
2003-2009 Z4 M Coupe and Roadster

This tensioner is for either the Water Pump or Alternator on cars with the mechanical belt tensioner system. Please check to ensure your car does not have the hydraulic tensioner. This tensioner comes with the pulley assembly.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Only for cars with Mechanical belt tensioner systems.

This item fits the following BMWs:
1992-1998 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
1991-1995 E34 BMW 525i
1997-2003 E39 BMW 525i 528i 530i
2004-2005 E60 BMW 525i 530i
2004-2006 E83 BMW X3 2.5i X3 3.0i
2000-2006 E53 BMW X5 3.0i
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i
2003-2005 Z4 BMW Z4 2.5i Z4 3.0i

This is an OEM INA Upper Idler Pulley, also known as the roller pulley or deflection pulley. The idler pulleys are known to be the primary sources for 'belt squealing'. The pulley is also encased in rubber which will crack over time. If left without service the rubber could fail completely, chucking the belt and leaving you stranded. Replacement is a very simple procedure and can be done anytime the fan is off the engine (belt replacement, water pump service, alternator replacement, etc).

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
2008-2010 E82 BMW 135i
2011 E82 BMW 1M Coupe
2006-2010 E90 BMW 335i 335xi 335i xDrive - Sedan
2007-2010 E92 BMW 335i 335is 335xi 335i xDrive - Coupe
2007-2010 E93 BMW 335i 335is - Convertible
2004-2010 E60 BMW 535i 535xi 535i xDrive

This is an OEM INA alternator pulley. Keep your belt drive system in top shape with this new pulley.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

RSL19 A favorite of BMW's Motorsport engineers, the Pagid RSL19 compound is an endurance pad based on the RS14 Black but with less friction to improve modulation and low pedal effort. These pads work best in a heat range up to 1,100* F. The combination of friction levels, fade stability, and long life for pads and rotors makes this a favorite for club and HPDE drivers. 

This is the set of FRONT pads.

This item fits the following BMWs:
2004-2011 E60 BMW M5
2006-2012 E63/64 BMW M6

This is a Valeo brand new 170 amp alternator. These alternators are built especially for extremes of heat, cold and high demand. Your BMW deserves nothing less than the best, which is why an OEM alternator is the best option. BMW alternators are built to last using the highest quality materials and the most technologically advanced processes. All alternator parts are 100% factory tested to assure that they meet or exceed original equipment specifications. And every alternator is fully load tested to guarantee compliance with BMW's strict performance specifications.

No core charge!

This item fits the following BMWs:
2006-2010 E60 BMW M5
2006-2010 E63 BMW M6

The latest in the Yellow line takes all of the RSL29 characteristics and adds a bit more aggressive behavior. Friction levels go up for more initial bite and better fade resistance. Modulation and release stays close to RSL29 levels. Pad and rotor wear is a little more than on the previous Yellows but still within reasonable levels and the RSL1 is still considered an extended endurance pad. Its development stemming from GT classes at Le Mans and Nürburgring.

Since Pagid pads tend to "out-gas" we recommend using these pads with a new gas-slotted or cross-drilled rotor for the best performance. Pagid brake pads are not compatible with previously used rotors, especially if used with a carbon or Kevlar based race pad.

This item fits the following BMWs:
2011+ E82 BMW 1M Coupe
2004-2005 E60 BMW 525i (automatic transmission only)
2006-2007 E60 BMW 525i, 525xi (all transmissions)
2008-2010 E60 BMW 528i, 528xi
2004-2007 E60 BMW 530i, 530xi
2008-2010 E60 BMW 535i, 535xi
2004-2010 E60 BMW 545i, 550i
2004-2010 E63 BMW 645Ci, 650Ci
2002-2008 E65 BMW 745i, 745Li, 750i, 750Li, 760Li
2007-2013 E9X BMW 335i, 335Xi, 335d
2008-2013 E9X BMW M3

This kit from Valeo is a simple way to easily convert your stock dual mass flywheel clutch system to a single mass system.

Dual mass flywheels allow for fluid-feeling clutch engagements and offer a more luxurious feel than single-mass flywheels. However, with these benefits come significant drawbacks. Why convert from a dual-mass flywheel to a single-mass flywheel?

Cost: Dual-mass flywheels are expensive, with the cost of replacement often times being double or triple than that of converting to a single-mass flywheel.
Serviceability: Single-mass flywheels can be resurfaced, eliminating the need to replace with the next clutch service. - something that is not recommended with dual-mass flywheels, as they contain a rubber section that is more failure-prone in high mileage application.
Simplicity: Single-mass flywheels lack the complexity of dual-mass flywheels, making them inherently more reliable. Dual-mass flywheels contain a rubber damper or hub that will, like all rubber components, wear out with time.
Pedal Feel: Many enthusiasts prefer to eliminate BMW's "Self Adjusting Clutch", which has been known to provide an unpredictable, inconsistent engagement point.
Driveability: Valeo's conversion kit has been designed to maintain nearly identical clutch and flywheel weight, ideal for keeping the clutch quiet and easy to drive.
Kit contents:

Single-mass flywheel
Non-Self Adjusting Clutch and pressure plate
Throw out bearing
Pressure plate bolts
Flywheel bolts
Clutch alignment tool

BBS Wheels combine decades of race proven quality and German engineering with stunning good looks. Utilizing the most cutting-edge manufacturing technologies based on a foundation of constant innovation continues to propel BBS into the future.

CI-R wheels consist of a pressure cast wheel surface and a flow formed rim structure.  Combining these two fabrication techniques yields a wheel that is extremely strong while remaining lightweight.

Using FEM analysis the engineers at BBS are able to precisely measure and optimize wheel properties before this process even begins. Once the forging process is complete, the meticulous finish work begins.
Back-milling is a process used to optimize the ratio between weight and stability. Using advanced computer analysis and a special CNC milling process the lateral parts that hold the wheel spokes, and are not relevant for stability, are removed. Extensive real-world simulation is used at this point to further ensure that no strength or stability has been lost.
Finally, BBS pays special attention in machining the undercut or back side of the wheel. To machine the undercut, all areas on the inner side of the wheel and the star hub that correspond to weight optimization are processed with special turning or milling tools and excess material is removed to reduce the rotating wheel mass. Special attention is hereby given to the optimization of the inner sides of the spokes and the bolt circle. With the application of these methods, BBS is able to produce more complex forms with increased stability and less material input.
These wheels come in a Satin Black and BBS ensures that their paint quality exceeds OE manufacturer specifications for durability and longevity. A final protective clear coat layer ensures that these wheels will be easy to clean and look amazing for years to come.

Please Note: Aggressive fitment, may require fender rolling or pulling.

Specs:

• 19x8.5 ET35 - qty 4
• Satin Black
• Center Bore: PFS
• Bolt Pattern: 5x120

BBS Wheels combine decades of race proven quality and German engineering with stunning good looks. Utilizing the most cutting-edge manufacturing technologies based on a foundation of constant innovation continues to propel BBS into the future.

SX Wheels are pressure cast using BBS own technology to produce an extremely strong and lightweight alloy. 

 Using FEM analysis the engineers at BBS are able to precisely measure and optimize wheel properties before this process even begins. Once the forging process is complete, the meticulous finish work begins.

These wheels come in Crystal Black Metallic and BBS ensures that their paint quality exceeds OE manufacturer specifications for durability and longevity. A final protective clear coat layer ensures that these wheels will be easy to clean and look amazing for years to come.

Please Note: Aggressive fitment, may require fender rolling/pulling.

Specs:

• 18x8 ET30 - qty 4
• Crystal Black Metallic
• Center Bore: PFS
• Bolt Pattern: 5x120