BMW Drivetrain Parts for BMW 5 Series E60 (2004-2010)

This is the stock twin mass flywheel for early N54 engines in the E82 135i, E9X 335i/xi, and E60 535i/xi (flywheel uses 8 mounting bolts). It's manufactured by OEM Shaeffler (LuK). Sachs recommends a new dual mass flywheel (DMF) on every other clutch replacement. There are several indicators for replacing the flywheel: damage to the clutch contact plate (from a severely worn clutch disc), grease leaking from inside (overheating), build-up of clutch material on the contact plate (excessive slipping and overheating), and failure of the internal damping system.

The dampening system uses rubber or coil springs to absorb driveline vibrations. Through age, excessive heat, and aggressive use the rubber loses its resilience and the metal springs lose their strength and become brittle. If the clutch and flywheel have become overheated the internal grease may break down as well. A DMF failure can be massive and catastrophic, not to mention dangerous as bits of metal and rubber fling themselves through the transmission bellhousing. Heat and aggressive driving will accelerate the wear so race and track cars should have their stock flywheels replaced at regular intervals or with any new clutch. Even normal street cars should plan for a new flywheel if it has high mileage.

DMF wear can only be checked with the transmission and clutch removed. If you can rotate the outer flywheel more than 20mm in either direction then it should be replaced.

A new pilot bearing (roller bearing) is included, pre-installed in the flywheel hub.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
2008-1/2009 E82 BMW 135i
2007-1/2009 E90 BMW 335i 335xi 335i xDrive - Sedan
2007-1/2009 E92 BMW 335i 335xi 335i xDrive - Coupe
2007-1/2009 E93 BMW 335i - Convertible
2007-1/2009 E60 BMW 535i 535xi 535i xDrive

Discover the precision and durability of our 13 Piece XZN Triple Square Driver Set. Each driver is ingeniously designed as a 2-piece unit, seamlessly integrating the bit and socket for effortless use. Crafted from top-tier S2 Steel, these standard-length drivers provide optimal reach and grip, catering to a diverse range of tasks.

Spanning from 4mm to 18mm, these drivers are your versatile solution, perfect for automotive repairs or intricate DIY projects. Organized in a foam padding, they stay secure and readily available whenever you need them.

With our commitment to quality, these drivers are backed by our LIFETIME REPLACEMENT program, ensuring your confidence in every task. Upgrade your toolkit today and experience the ease of working with high-quality tools tailored to meet your demands.

Includes:

• Foam casing
• 4 mm
• 5 mm
• 6 mm
• 7 mm
• 8 mm
• 9 mm
• 10 mm
• 11 mm
• 12 mm
• 13 mm
• 14 mm
• 16 mm
• 18 mm

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Shifter slop is a common complaint among all BMW models. Some of that play comes from the bushings where the shifter carrier mounts to the transmission. The original rubber carrier bushings don't last very long and when they get too soft the shifter flops around. These Delrin bushings have almost no deflection and will last much longer than the factory rubber, giving you precise shifting for many years.

Note: this is only one part of the shift linkage and there may be other components that need replacing to improve shifting feel.

New carrier bushing pins are included.

This item fits the following BMWs:
11/2003-2007 E60 BMW 525i 530i

An excellent performance upgrade so you can enjoy quicker revs and eliminate excess turbo lag. Made of high quality 6061-T6 billet aluminum, with a high-carbon steel replaceable friction surface, this flywheel from Clutch Masters is sure to be a great upgrade for anyone looking to reduce crankshaft drag and increase acceleration.

Typical benefits of a Clutch Masters lightweight flywheel:

• Reduced mass equals increased acceleration
• CM uses only 6061-T6 aircraft grade or better billet aluminum in the manufacturer of its flywheels
• CM uses an OE steel ring gear secured by bolts
• CM offers a limited lifetime warranty
• CM Billet Aluminum Flywheels meet SFI Spec 1.1 or 1.2

Elevate your lifting experience with the Schwaben Long Low Profile - High Lift Floor Jack. Certified for excellence and designed with a keen understanding of European car enthusiasts' needs, this jack is a testament to precision, durability, and performance. Don't compromise on quality—choose the Schwaben advantage for all your lifting endeavors.

Designed with precision, crafted for performance, and backed by our lifetime replacement program, the Schwaben Long Low Profile - High Lift Floor Jack is a must-have tool for every European car aficionado. This jack is engineered to cater to the unique needs of low ground clearance vehicles, ensuring that your prized possessions are lifted with care and precision.

Key Features:

• One Pump Reach: With its innovative one-pump feature, this floor jack effortlessly reaches contact on most cars, streamlining your lifting process.
• Low Profile Advantage: Boasting a mere 2-3/4" low height and a deep-reach lift arm, this jack is tailored for those sports cars and luxury vehicles that ride close to the ground.
• Hydraulic System Protection: The dual pump pistons are expertly shielded to thwart contaminants from compromising the hydraulic system's integrity.
• Built for Durability: Crafted with heavy gauge construction and fortified with rolled edges, this floor jack guarantees unwavering strength and longevity.
• Precise Control: The U-Joint release mechanism offers meticulous control over load descent at any handle position, ensuring the safety of both you and your vehicle.
• Maneuverability Redefined: Upgraded casters allow seamless maneuverability and effortless positioning of the jack, empowering you to find that perfect lifting spot.
• Safety First: The internal by-pass valve prevents over-pumping, shielding the hydraulic system from stress-induced issues.
• Vehicle Protection: A full cover rubber saddle pad and a protective foam cover on the handle are in place to prevent any unintended damage during the lifting process.
• Impressive Capacity: With a remarkable 4000 lb. capacity, this jack is ready to tackle a range of European vehicles.
• LIFETIME REPLACEMENT: Like almost all Schwaben products, this jack is backed by our lifetime replacement program in case anything goes wrong!

Specifications:

• Min Height: 2-3/4"
• Max Height: 24"
• Handle Length: 49-1/4"
• Jack Body Length: 35"
• Length from Pivot Point to Center of Jack Pad: 22"
• Front Casters: 2-1/2" diameter x 2" width
• Saddle Diameter: 4" with full saddle pad
• Weight Capacity: 4000 lbs.
• ANSI / ASME PALD 2009 Certified

Also included are the Schwaben Aluminum 3-Ton Jack Stands. These ultra-light Schwaben jack stands only weigh 4.7 lbs each. Fit and finish on these stands show how much pride in workmanship goes into our stands. These stands feature all-aluminum construction with heavy-duty flanged bases to safely stabilize loads. Features 6 locking positions for a secure load in multiple heights. The load pin is extra heavy duty at .584 in. diameter and features a posi lock ball to ensure the pin stays in place.  

• Min. Height is 10.6".
• Max Height is 15.4".
• Large 7" diameter base.
• Outer support tube is 2-1/8" in diameter.

For replacement parts, please call us and ask for:

• ES#4430428 - Replacement Screw Set
• ES#4430429 - Replacement Front Wheel
• ES#4430430 - Replacement Caster Wheel

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

An SFI approved single mass flywheel is recommended for this application to get optimal performance. This clutch system is designed for the racing climate. The pressure plate is precision balance for vibration free operation at high RPM. The pressure plate fulcrum is altered for a positive disengagement and a quick shift. The disc is engineered with a Dual Damped design to provide accurate control when accelerating through corners. The friction material is a hybrid using a full face Feramic (Sintered Iron) lining on the flywheel side and a high metal content Organic lining on the pressure plate side. Engagement is positive yet buffered due to the high graphite content unique to Feramic facings.

Stage 2 Endurance Clutch Kits:

Recommended uses are daily and street with an emphasis on Rally and Endurance racing.

Rated to hold 495lbs/ft of torque.

Featuring a solid-hub center section for use with an OE dual-mass flywheel

The Pneumatic CV Boot Installer simplifies CV boot installation through air power. Its sturdy metal fingers stretch the boots, enabling effortless slipping over constant velocity joints without the need to remove them from the axle.

This efficient tool reduces the once time-consuming two-hour task to a mere 20-minute job, saving significant labor and effort. Operating it is a breeze?all you need is an air compressor, making it convenient for both professionals and enthusiasts in the automotive industry.

Crucially, it works exclusively with flexible CV boots, and is not compatible with plastic boots. With its user-friendly design, this installer is a game-changer in automotive maintenance, offering a hassle-free solution for CV boot installation.

Plus, our Air Powered CV Boot Installer comes with a LIFETIME REPLACEMENT guarantee, ensuring you never have to worry about spending hours on boot installations again!

Working in collaboration with Competition Clutch, the up and coming German automotive performance company DKM has released a new line of high quality clutches made to satisfy your stock and modified performance needs! If you're having problems keeping power to the wheels, DKM has the solution. Their design, using high-grade materials, gives you increased strength and heat tolerance preventing wear and fade, ensuring increased torque capacity, quicker shifts, and a longer clutch life.

Tracking your vehicle is all fun and games until your start burning through clutches as fast as you can afford to replace them. To end this cycle, the MS Twin Disc Clutch Kit is designed to hold up to 100 to 200% more torque capacity and provide you with a much improved clutch life span. The two organic disc setup provides additional contact surface areas to more evenly distribute pressure and heat for both a boost in performance and wear prevention.

Kit Contents:
Pressure Plate
Two Organic Discs
Steel Single Mass Flywheel
Pilot Bearing/Bushing and Throw-out Bearing (when applicable)
Alignment Tool
Rated for upwards of 660 ft/lbs of torque

This kit from Valeo is a simple way to easily convert your stock dual mass flywheel clutch system to a single mass system.

Dual mass flywheels allow for fluid-feeling clutch engagements and offer a more luxurious feel than single-mass flywheels. However, with these benefits come significant drawbacks. Why convert from a dual-mass flywheel to a single-mass flywheel?

Cost: Dual-mass flywheels are expensive, with the cost of replacement often times being double or triple than that of converting to a single-mass flywheel.
Serviceability: Single-mass flywheels can be resurfaced, eliminating the need to replace with the next clutch service. - something that is not recommended with dual-mass flywheels, as they contain a rubber section that is more failure-prone in high mileage application.
Simplicity: Single-mass flywheels lack the complexity of dual-mass flywheels, making them inherently more reliable. Dual-mass flywheels contain a rubber damper or hub that will, like all rubber components, wear out with time.
Pedal Feel: Many enthusiasts prefer to eliminate BMW's "Self Adjusting Clutch", which has been known to provide an unpredictable, inconsistent engagement point.
Driveability: Valeo's conversion kit has been designed to maintain nearly identical clutch and flywheel weight, ideal for keeping the clutch quiet and easy to drive.
Kit contents:

Single-mass flywheel
Non-Self Adjusting Clutch and pressure plate
Throw out bearing
Pressure plate bolts
Flywheel bolts
Clutch alignment tool

Since established in 2004, GSP North America has positioned itself as a leading supplier of New Axles in North America.GSP’s new axle program consistently offers the best application coverage, most SKU count, and more new numbers than any other competitors. GSP’s hub assembly program was introduced to North America market in 2010 and has grown into one the most trustable programs in US market.

This item fits the following BMWs: 

1997-2003 E39 BMW 525i 528i 530i 540i M5 
2004-2010 E60 BMW 525i 525xi 530i 530xi 528i 528xi 528i xDrive 535i 535xi 535i xDrive 545i 550i

GKN is a global company specializing in meeting the needs of the growing automotive industry. Every time you travel by road or air almost anywhere in the world it is likely that GKN is helping you on your way. Designing, manufacturing and service systems and components for original equipment manufacturers, GKN is also competitive in the automotive aftermarket.

Continuously evolving, pioneering new technologies and reinventing existing ones, GKN is always striving to better themselves in everything they do.

Advanced Clutch Technology (ACT) designs, engineers and develops products by leveraging decades of track and performance street experience. Advanced CAD, FEA simulation, and CAM tools help ensure highly optimized performance, reliability, and repeatability. These key advantages are produced by combining the best engineering and design methodologies with the latest in materials and manufacturing techniques.

ACT clutch kits stand unequaled in terms of consistent pedal feel, high torque capacity, long wear life and durability. In-house manufacturing is critical in tuning components specifically to each individual application while maintaining the predictable ACT pedal feel across the entire catalog.

This clutch kit is their most popular and features a Heavy Duty pressure plate, a Performance Street sprung clutch disc, and an XACT Streetlite Flywheel.

The heavy duty pressure plate included offers a 20-50% clamp load increase, stock-moderate  pedal feel, and heat treated diaphragms for increased strength and performance.

Next in this kit is the Performance Street clutch disc. This is the most popular sprung clutch disc and features high quality organic friction material with a high copper content for improved heat transfer and a steel backed lining for increased strength in burst load circumstances. This organic clutch disc has a significantly higher torque capacity than a stock disc but still retains a long life span and operates quietly and reliably.

The final main component is the XACT Streetlite Flywheel. This option is the most popular thanks to it versatility for street driving and drag/track style racing, its lighter weight for increased throttle response, and its single mass design.

Clutch Kit Specs:

• Torque Rating: 440 ft/lbs
• 45% torque capacity increase over stock!
• Type of Disc: Street
• 26-count spline
• Spline Size: 1-3/8" inch
• Disc Weight: 3.5 lbs
• Pressure Plate Weight: 10.2 lbs
• Flywheel Weight: 24.5 lbs
• 1 year Warranty from retail purchase date!

Enhance Vehicle Performance with SPEC Clutch Kit

Upgrade your vehicle's performance with the SPEC clutch kit, engineered to efficiently transfer power to the wheels during high-performance driving scenarios. Prevent premature wear and slippage with this kit, offering a torque capacity of up to 456ft.lbs. When combined with the SPEC lightweight aluminum flywheel, experience rapid and efficient engagement.

Designed for a variety of applications including street, drag, autocross, road racing, pulling, rallye, and drift, this kit bridges the gap between stage 2 and stage 3, delivering enhanced drivability and engagement quality.

Key Features:

• Multi-friction disc with carbon semi-metallic and Kevlar
• 15-20% higher torque capacity than stage 2 clutches
• Double sprung hub with spring cover relieves for flexibility
• Heat-treated components for enhanced strength and durability

Experience increased acceleration, reduced turbo lag, improved mid-range torque, and decreased parasitic drag for increased crank efficiency with the SPEC clutch kit. Compatible with vehicles manufactured between 2006-2009.