BMW Intake Parts for BMW 5 Series E60 (2004-2010)

The factory plastic gears in BMW S65 and S85 throttle body actuators are notorious for premature wear due to mechanical stress, engine vibration, and heat cycling. Over time, this wear leads to excessive play, throttle response issues, and eventual failure. This can cause DME fault codes, limp mode, and DSC malfunctions. While replacing both throttle actuators is costly, even new OEM units will eventually suffer the same fate.

Thankfully, ECS has developed the ultimate solution for E9X M3, E60 M5, and E63/64 M6 owners! These Upgraded Throttle Body Actuator Gears are constructed of Teflon-reinforced nylon, significantly reducing friction and gear tooth wear for long-term reliability. Each gear comes pre-installed on a 4140 steel shaft, strengthening the assembly and ensuring a hassle-free installation. With this cost-effective and durable fix, you can eliminate throttle actuator failures for good!

Features & Benefits:

Upgraded Teflon-reinforced nylon gears – Superior to factory plastic-on-plastic gears, reducing wear and extending lifespan. Pre-installed 4140 steel shafts – Increases durability and simplifies installation. Prevents common actuator failures – Resolves worn gear issues that cause CELs, limp mode, and DSC/DME errors. Cost-effective alternative to full actuator replacement – Saves hundreds in parts and labor. Factory-like fitment – Engineered for precise compatibility and long-term reliability. Built to withstand heat and mechanical stress – Ensures consistent throttle performance and extended service life.

Vargas Turbo has you covered when you are installing a custom turbo setup. With all of the adapters you need and all the valves necessary, the only real limiting factor is your imagination!

This is a 1/2" (fits -8AN hos perfectly as well) CNC Billet check valve that can be used for a variety of uses including a vacuum/boost check valve when removing the stock PCV system, and still wanting to run the vacuum to the crankcase. Rated at over 100 psi, with a cracking psi of .25psi.

This part fits the following BMW engines:
2006-2012 N54

Vargas Turbo has you covered when you are installing a custom turbo setup. With all of the adapters you need and all the valves necessary, the only real limiting factor is your imagination!

The VTT PCV Flapper delete is used to get rid of the factory flapper, and add a -10 fitting on N54 powered vehicles. This will allow you to run a single or dual external catch can, or your own custom set up.

This fitting is made from 6061-T6 aircraft aluminum anodized black and comes with O-ring, and a stainless steel holding clip.

This part fits the following BMW engines:
2006-2012 N54

• Seamless plug-and-play installation
• Minimizes leakage for enhanced turbocharger performance
• Retains OE control for optimal operation
• Superior thermal performance to maximize boost without stressing the turbocharger

In addition to the weak stock chargepipe, the factory N54 diverter valves can also be a source for boost leaks. The diverter valve takes overboost and re-directs it back through the intake and turbos instead of allowing it to pass into the intake manifold. It's the same as a blow off valve (BOV) but instead of releasing into the engine bay, it stays contained to the engine. The stock diverter valves (DV) are plastic and connect with more plastic into the chargepipe and turbo inlet pipes. The plastic can become brittle and crack even on stock engines and leak boost, which leads to a loss in power and performance.

Turbosmart has developed two kits to replace and upgrade the stock diverter valves - a direct replacement kit (shown) and a combination DV/BOV "Dual Port" kit. This direct replacement kit includes new high-performance DV and stronger silicone hose to connect them to the turbo inlet pipes (Vargas silicone inlets are recommended). The Turbosmart Kompact DV will give you all of the strength and reliability you need to take your turbo build to the next level.

You will also need T#553932 

Improve the performance of your BMW's N54 3.0L engine with the HKS BOV in a striking silver finish. Blow off valves play a crucial role in turbocharger systems, and selecting the right one is essential when enhancing the performance of a turbocharged vehicle. The aftermarket HKS BOV, tailored for larger quantities of air and higher pressures, ensures optimal handling of additional airflow.

• Enhanced Turbocharger Performance: The HKS BOV is designed to complement turbocharger systems, optimizing overall performance.
• Increased Airflow Handling: Aftermarket blowoff valves handle larger quantities of air, accommodating the demands of performance accessories.
• Silver Finish: The distinctive silver finish adds a touch of style to your BMW's engine bay.
• Tailored for Higher Pressures: Specifically designed to cope with increased pressures associated with performance upgrades.

Upgrade your BMW's N54 3.0L engine with the HKS BOV in silver, ensuring a reliable and stylish addition to your turbocharger system.