BMW Drivetrain Parts for BMW 5 Series E61 (2006-2010)

A lightweight aluminum flywheel is a great way to increase throttle response and free up horsepower by reducing drivetrain loss. Factory flywheels are built to minimize engine and transmission vibrations, making them heavier and requiring more energy to make them spin. An aluminum flywheel can save lots of weight over the stock steel unit - sometimes over 50%. While the dampening effect of the stock flywheel is reduced, most enthusiasts would agree that the increase in performance is well worth it. In addition, the lighter flywheel allows the engine to spin more freely, improving throttle response.

This JB Racing lightweight aluminum flywheel kit and is designed to be used with the included factory clutch, making replacement and service easy and inexpensive, especially compared to specialized racing clutches. It also preserves the driveability of your car on the street, and enthusiasts tolerant of a mild to moderate NVH increase will be especially taken with this setup. In addition, the JB Racing flywheel can be easily rebuilt with a new clutch contact surface, allowing you to enjoy faster revs and superior response for many years to come.

Stock Flywheel Weight: 24-31 lbs.

JB Racing Lightweight Aluminum Flywheel: 12 lbs.

This item fits the following BMW Chassis:
E61/1, E82/88, E9x, Z4

Fits the follow engines:
N52 3.0L

This is an OEM LuK stock twin mass flywheel for the N52 non-turbo engine in the 128i, 325i/328i/330i, 525i/528i/530i, and Z4 30i. It's manufactured by OEM supplier LuK. Sachs recommends a new dual mass flywheel (DMF) on every other clutch replacement. There are several indicators for replacing the flywheel: damage to the clutch contact plate (from a severely worn clutch disc), grease leaking from inside (overheating), build-up of clutch material on the contact plate (excessive slipping and overheating), and failure of the internal damping system.

The dampening system uses rubber or coil springs to absorb driveline vibrations. Through age, excessive heat, and aggressive use the rubber loses its resilience and the metal springs lose their strength and become brittle. If the clutch and flywheel have become overheated the internal grease may break down as well. A DMF failure can be massive and catastrophic, not to mention dangerous as bits of metal and rubber fling themselves through the transmission bellhousing. Heat and aggressive driving will accelerate the wear so race and track cars should have their stock flywheels replaced at regular intervals or with any new clutch. Even normal street cars should plan for a new flywheel if it has high mileage.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

DMF wear can only be checked with the transmission and clutch removed. If you can rotate the outer flywheel more than 20mm in either direction then it should be replaced.

A new pilot bearing (roller bearing) is included, pre-installed in the flywheel hub.

Automatic transmissions are reliable, shift smoothly, and can last without issue so long as they are properly maintained. Over time, the transmission fluid becomes thick and the filter becomes contaminated with small metal particles. This can cause excess wear, high transmission operating temperatures, and eventual failure. To prevent this we recommend changing your filter, fluid, and seals to ensure your transmission continues to operate flawlessly. We recommend filter and fluid changes every 50,000 miles. 

Kit Includes:

• Automatic transmission oil pan with integrated filter 
• Oil pan gasket
• Drain plug with sealing washer
• Fill plug with sealing washer
• 7 quarts Redline D4 automatic transmission fluid

Fits the following BMWs:
E84 BMW X1 xDrive35i
​E90 BMW 325i/xi, 328i/xi (with GA6HP19Z automatic transmission), 330i/xi, 335i/xi
​E91 BMW 325i/xi, 328i/xi (with GA6HP19Z automatic transmission)
​E92 BMW 328i/xi (with GA6HP19Z automatic transmission), 335i/x
​E93 BMW 328i (with GA6HP19Z automatic transmission),  335i
E60 BMW 525i/xi, 528i/xi, 530i/xi, 535i/xi
E61 BMW 525i, 530xi, 535xi
E70 BMW X5 xDrive30i
E71 BMW X6 35iX
E82/88 BMW 128i(with GA6HP19Z automatic transmission), 135i (N54)
F01/02 BMW 740i/Li
E85/86/89 BMW Z4 3.0i/Si sDrive30i M54 N52

Tired of dealing with excess shifter slop and a mushy shifter? The Turner Shifter Rebuild & Upgrade Kits will restore your shifter's crisp feel and eliminate excessive movement that develops over time with wear. Included in this kit are all the common wear components and OE quality bushings that will give you a tighter shifting feel and will hold up like a day 1 BMW.

This kit is perfect to restore your driving pleasure!

See the included components under Kit Contents below.