BMW Fuel System Parts for BMW 5 Series E61 (2006-2010)

Clear BMW chassis

Looking for a BMW fuel pump, BMW gas cap or other BMW fuel system related items? You've found the right place. Your BMW fuel delivery system is a critical system, and any failure can rended your BMW dead in the water. Whether your fuel pump has stopped pumping, a fuel injector is clogged or not spraying, or your gas cap is either lost or not properly sealing, we likely have what you are looking for. We stock thousands of BMW fuel system parts so if you don't see what you are looking for, just give us a call.

Sub-Categories

Sort By:

ARC Upgraded Fuel Pump Control Module - Dual Ball Bearing Fan - EKPM3...

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:28304525

Part#: EKP-HW05-E-SF

In Stock

$ 199.99 USD

Add to Wish List

Qty

$ 199.99 USD

Add to Wish List

Arc Terminator now offers upgraded EKMP3 Fuel Pump Control Modules featuring a 22 Amp INCREASE in maximum current capacity over an OEM EKPM3. This allows for more current to be supplied to your low-pressure fuel pump (LPFP) without risking thermal overload, which often leads to your car shutting down. This means that you won't have to worry about being stranded on the side of the road while waiting for your EKP module to cool down, especially when you've installed a large low-pressure fuel pump such as a Walbro 525lph. How does the integrated automatic cooling work? The integrated automatic cooling works by us installing a thermal activation switch directly onto the new half bridge IC. When the half bridge IC reaches 50°C, the 40mm fan will turn on and keep running until the IC is below 50°C or until the EKMP3 stops receiving power. I have an EKPM2, can I upgrade to this? Yes. You can upgrade to this. We recommend using the HW05 and below module. You will need to code it in order for it to function properly. Can I run more than 1 low-pressure fuel pump off of this module? No. We do not recommend that you use more than one low-pressure fuel pump with any EKP module due to the factory wiring supplying power to the EKP Module is only 12 gauge, which is not rated for the type of power demands that two low-pressure fuel pumps would require.

Show More Show Less

VTT N54 Vacuum Pump Block Off Plate

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:11497328

Part#: VTT-N54-VACUUM-B

In Stock

$ 127.99 USD

Add to Wish List

Qty

$ 127.99 USD

Add to Wish List

Looking to remove the HPFP or DI system on your N54? this plate will block the vacuum pump and prevent oil leaks. You will need to remove any fuel lines, etc. Kit includes Block Plate Note – Plates may come in a clear or anodize black finish depending on stock on hand

Show More Show Less

VTT BMW N54 “DI Injector” Delete Kit

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:11497326

Part#: VTT-N54-DI-DELET

Ships in 1 Business Day

$ 339.99 USD

Add to Wish List

Qty

$ 339.99 USD

Add to Wish List

Looking to get rid of the troublesome and expensive DI injectors on your BMW N54 and move to PI only and a standalone? If so VTT has you covered with its new N54 PI delete kit. This kit allows you to SAFELY remove the DI injectors, install our delete fittings, and run PI only. We machined these deletes from 310 Stainless for extreme heat, and corrosion resistance, and include 3 hold downs. These DI deletes COMPLETELY get rid of all factory provisions, including the seal. If the seal is left intact with no fuel to cool the injector or delete it will quickly overheat and melt the delicate seal causing combustion gasses to escape the engine creating misfires, and worse possibly damaging your injector bore on the cylinder head. Our deletes are machined to be a press fit into the cylinder, and can be either cooled with liquid nitrogen, and dropped in, or tapped in with a hammer, and then held down with the included hold downs. We also include M6 tapped holes on the top of each one in case they need to be removed you can attach a slide hammer, and remove the delete. These are sold as a kit and come with the following 6 – 310 Stainless DI Delete fittings 3 – Hold down brackets Completetion of this kit will require the purchase of HPFP delete plate - ES# 4623950 PLEASE NOTE: THIS KIT REQUIRES EXTENSIVE MODIFICATIONS TO CONVERT YOUR ENGINE TO PI ONLY. THIS INCLUDES BUT IS NOT LIMITED TO A FULL PORT INJECTION SOLUTION, AND STAND-ALONE TO RUN THE PI SYSTEM. WE RECOMMEND THIS PNP SYSTEM USING THE MAXX ECU IT PROVIDES ALL YOU NEED TO GET UP AND RUNNING WITH PI ONLY ON THE TUNING SIDE OF THINGS – https://www.pnpecu.com/pnpecu-maxxecu-n54-pnp-kit-437-p.asp

Show More Show Less

Upgraded EKPM3 Fuel Pump Control Module - Noctua Fan

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:28304530

Part#: EKP-HW05-E-NF

Back Ordered

$ 229.99 USD

Add to Wish List

Qty

$ 229.99 USD

Add to Wish List

Arc Terminator now offers upgraded EKMP3 Fuel Pump Control Modules featuring a 22 Amp INCREASE in maximum current capacity over an OEM EKPM3. This allows for more current to be supplied to your low-pressure fuel pump (LPFP) without risking thermal overload, which often leads to your car shutting down. This means that you won't have to worry about being stranded on the side of the road while waiting for your EKP module to cool down, especially when you've installed a large low-pressure fuel pump such as a Walbro 525lph. Includes 40mm Noctua Silent Fan! How does the integrated automatic cooling work? The integrated automatic cooling works by us installing a thermal activation switch directly onto the new half bridge IC. When the half bridge IC reaches 50°C, the 40mm fan will turn on and keep running until the IC is below 50°C or until the EKMP3 stops receiving power. I have an EKPM2, can I upgrade to this? Yes. You can upgrade to this. We recommend using the HW05 and below module. You will need to code it in order for it to function properly. Can I run more than 1 low-pressure fuel pump off of this module? No. We do not recommend that you use more than one low-pressure fuel pump with any EKP module due to the factory wiring supplying power to the EKP Module is only 12 gauge, which is not rated for the type of power demands that two low-pressure fuel pumps would require.

Show More Show Less

E60 / E61 EKPM2 EKPM3 PNP Cooler Kit - (5 Series)

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms
A Must For Cars With Upgraded LPFPs

T#:26305056

Part#: E60-EKP-PNPC

Ships in 1 Business Day

Starting at $ 59.99 USD

Add to Wish List

Starting at $ 59.99 USD

Add to Wish List

The full plug-and-play EKPM3 / EKPM2 cooler kit is designed specifically for E60 BMWs using an EKPM3 or EKPM2 fuel pump control module. This is recommended for anyone using a low-pressure fuel pump that is larger than the OEM fuel pump. There are two versions of the kit, one with a relay and one without a relay. The relay kit is for those who would prefer to not put an additional load on their 12v outlet circuit due to using that circuit for something with a high load already. The non-relay kit will work perfectly for any normal use of the 12v outlet circuit and only adds up to 0.30 amps onto that circuit, which is very minimal. For all M5s, you will need to use an EKPM2 kit as the EKP module is physically the same size as an EKPM2. Full Kit Contents: 1x PNP EKPM3 / EKPM2 Cooler Housing With 5015 Fan and Fused Relay 1x 14x14x6mm Heatsink With Thermal Tape 1x 14x9x5mm Heatsink With Thermal Tape 1x 9x9x5mm Heatsink With Thermal Tape (EKPM3 Kit) 2x 9x9x5mm Heatsink With Thermal Tape (EKPM2 Kit) 4x 4" Zip Ties 1x Alcohol Wipe 2x 2 Amp Standard Blade Fuses Why this kit exists: The EKPM3 and EKPM2 have been shown to overheat and cause vehicle shutdown issues when larger fuel pumps that draw more current than OEM are used. This shutdown comes from critical components on the EKPM3 and EKPM2 overheating when larger current draws are coming from the fuel pump. The PNP kit comes with heatsinks for the most heat-sensitive and heat-producing components in the EKPM3 / EKPM2 to further increase cooling effectiveness. When paired with a potent 5015 blower fan that directs a large amount of airflow through the cooler housing, the EKPM3 / EKPM2 stays significantly cooler, which prolongs the life of the module. We also recommend anyone using a larger fuel pump than OEM to properly code their EKP module with Pro-Tool's built-in "Voltage Fix" feature.

Project Cars

SELECT YOUR BMW

BMW Fuel System Parts for BMW 5 Series E61 (2006-2010)

Sub-Categories

ARC Upgraded Fuel Pump Control Module - Dual Ball Bearing Fan - EKPM3...

VTT N54 Vacuum Pump Block Off Plate

VTT BMW N54 “DI Injector” Delete Kit

Upgraded EKPM3 Fuel Pump Control Module - Noctua Fan

E60 / E61 EKPM2 EKPM3 PNP Cooler Kit - (5 Series)

Select Vehicle

Category

Brand

Price

Shipping

Narrow Results