Home
Suspension

BMW Suspension Parts for BMW 6 Series E64 (2004-2010)

Your BMW's handling is determined by the capabilities and age of your suspension components. Our selected aftermarket performance suspension like coilovers, lowering springs, cup kits, and dampers can improve the handling of your BMW dramatically. With those upgrades comes the needs for proper adjustment; our recommended supporting modifications comes stiffer sway bars, bushings, and adjustable camber/caster plates, to name a few found on this page. Completely build your suspension for the most competitive BMW driving experience, achieve your perfect look, or simply replace your worn suspension with our recommended parts.

Sub-Categories

Sort By:

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E36, E39 ...

T#:389645

Part#: 192416-1J

In Stock

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Location: Front
Type: Street, Stage 1
Bearing: captive-ball fully encased in polyurethane

These front adjustable camber/caster plates will replace your stock front upper strut bearing. The KMAC plates are a 'floating' design so camber and caster are adjusted together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Since these replace your stock strut bearings they are designed to work with a stock-type spring only. And when installed correctly will not significantly alter ride height. Adjustment is easily done by loosening the three nuts on top of the tower and sliding the camber plate into the position you want, then re-tighten the nuts. These mounts can be installed two ways - for camber correction or swapped side-side for increasing negative camber. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC)
2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i
2004-2011 E63 E64 BMW 645ci 650i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003 E52 BMW Z8 Roadster (without EDC)

Show More Show Less

Adjustable Front Camber Bushings

T#:31522921

Part#: 193616-6H

Ships on Aug 19, 2026

$ 320.00 USD

Add to Wish List

Qty

$ 320.00 USD

Add to Wish List

Rear Guide Rod - Left or Right - E39, E60, E63, E65

T#:338099

Part#: 33326777424S1

Ships on Oct 19, 2026

Starting at $ 79.99 USD

Add to Wish List

Starting at $ 79.99 USD

Add to Wish List

This rear guide rod for the E39 chassis helps to control the toe alignment of the car (the horizontal in/out angle of the tire). There is a rubber bushing on the inside and a ball joint on the outside mounting point. When the bushings on the arm wear out they can contribute to a 'wandering' or 'loose' or unstable feeling in the rear. There may also be a clunking noise associated with bumps. This arm is just one part of the rear suspension, and other parts should be checked to confirm which one is causing the issues. For a complete overhaul of the rear suspension, check out our rear control arm package here .

Brand: Febi-Bilstein, Meyle
Price is for each - order 2 to replace both on the car.
This item fits the following BMWs:
12/2001-2003 E39 BMW 525i 528i 530i 540i M5
2004-2010 E60 BMW 525i 525xi 530i 530xi 528i 528xi 528i xDrive 535i 535xi 535i xDrive 545i 550i
2004-2011 E63 E64 BMW 645ci 650i
2002-10/2006 E65 BMW 745i 745li 750i 750li 760i 760li

Show More Show Less

Front Suspension Refresh Kit - Level 1

T#:30463953

Part#: 31102348046KT2

In Stock

Sale - Save 15% $ 877.99

This product was last offered at the strikethrough price on
06-24-2026

$ 744.54 USD

Add to Wish List

Qty

Sale - Save 15%

$ 877.99

This product was last offered at the strikethrough price on
06-24-2026

$ 744.54 USD

Add to Wish List

Upgrade your BMW’s front suspension with our high-quality Front Suspension Control Arm Kit, designed to restore stability and precision to your vehicle. Over time, worn control arms can lead to creaking, groaning, and instability, especially at highway speeds. Our comprehensive kit ensures a complete overhaul with all necessary components pre-assembled for easy installation.

Key Features:

Enhanced Stability: Say goodbye to wandering and instability on the road with new, durable control arms. Complete Solution: Our kit includes all four front control arms, two ball joints, and essential installation hardware. Premium Quality: Assembled by enthusiasts at ECS Tuning, ensuring top-notch performance and reliability. Ready for Installation: All related ball joints and bushings are pre-installed, saving you time and effort. Kit Includes:

4 Front Control Arms Installation Hardware Give your BMW the suspension upgrade it deserves. Enhance your driving experience with our Front Suspension Control Arm Kit and enjoy the confidence of driving a well-maintained vehicle. Order now and experience the difference in ride quality and stability.

Show More Show Less

KMAC Street Rear Adjustable Camber/Toe Bushings - E60 E63 E65 E53 X5 ...

T#:389668

Part#: 193726J

Special Order: No Guaranteed ETA

$ 380.00 USD

Add to Wish List

Qty

$ 380.00 USD

Add to Wish List

Perfect for lowered cars that need to dial out negative camber to preserve tires. Also perfect for track cars - easily dial in toe and camber for the track for better handling. Priced per set. Fits BMW E60 E63 E65.

This item fits the following BMWs:
2004-2010 E60 BMW 525i 525xi 528i 528xi 530i 530xi 535i 535xi 545i 550i M5
2004+ E63 BMW 645ci 650i M6
2002-2008 E65 BMW 745i 745li 750i 750li 760i 760li
2000-2006 E53 BMW X5 3.0i, X5 4.4i, X5 4.6is, X5 4.8is

Show More Show Less

KMAC Stage 2 Street/Track Front Adjustable Camber/Caster Plates - E36...

T#:389647

Part#: 192416-2L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Street/Track, Stage 2
Bearings: main PTFE-lined pillow-ball bearing suspended in polyurethane; self-lubricating radial axial bearing/bushing in upper spring plate
Springs: includes OEM size upper spring perch, 60mm upper spring perch, and 2.5" upper spring perch

The Stage 2 KMAC plates are a mixed track and street camber/caster plate meant to be used in a variety of suspensions and setups. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions and upper spring perches are included for OEM springs, 60mm, and 2.5" coil over springs. The upper perch assembly incorporate a self-sliding radial bushing that allows the spring to spin during its travel instead of bind. This reduces tension on the spring and helps reduce noise and spring 'popping' noises. Bearing inserts, spacers for correct articulating angles, and 3 sizes of upper nut adapters included. The urethane bushings and bearings are replaceable if they wear out. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Basic instructions included but professional installation is required.

Note: suspensions vary from manufacturer to manufacturer. The proper stacked height and clearances are required. K-Mac includes bearing adapters, spacers, and various top nuts but it is still the responsibility of the installer to ensure a correct and safe fitment. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC)
2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i
2004-2011 E63 E64 BMW 645ci 650i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003 E52 BMW Z8 Roadster (without EDC)

Show More Show Less

KMAC Stage 3 Street/Track Front Adjustable Camber/Caster Plates - E36...

T#:389646

Part#: 192416-3L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Street/Track, Stage 2
Bearings: main PTFE-lined pillow-ball bearing suspended in polyurethane; self-lubricating radial axial bearing/bushing in upper spring plate
Springs: includes OEM size upper spring perch, 60mm upper spring perch, and 2.5" upper spring perch

The Stage 3 KMAC plates are a mixed track and street camber/caster plate meant to be used in a variety of suspensions and setups. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions and upper spring perches are included for OEM springs, 60mm, and 2.5" coil over springs. The upper perch assembly incorporate a self-sliding radial bushing that allows the spring to spin during its travel instead of bind. This reduces tension on the spring and helps reduce noise and spring 'popping' noises. Bearing inserts, spacers for correct articulating angles, and 3 sizes of upper nut adapters included. The urethane bushings and bearings are replaceable if they wear out. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Basic instructions included but professional installation is required.

Note: suspensions vary from manufacturer to manufacturer. The proper stacked height and clearances are required. K-Mac includes bearing adapters, spacers, and various top nuts but it is still the responsibility of the installer to ensure a correct and safe fitment. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i
6/1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i - Convertible
1997-2003 E39 BMW 525i 528i 530i 540i (not for cars with EDC)
2004-2010 E60 BMW 525i 530i 528i 535i 545i 550i
2004-2011 E63 E64 BMW 645ci 650i
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
2000-2003 E52 BMW Z8 Roadster (without EDC)

Show More Show Less

KMAC Stage 3 Track Front Adjustable Camber/Caster Plates - E39 540/M5...

T#:389662

Part#: 193616-3L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Track, Stage 3
Bearing: PTFE-lined pillow-ball, no bushing

KMAC Stage 3 camber/caster plates are designed for track or race-only situations where comfort and noise are not the primary concerns. The Stage 3 camber plates use a pillowball bearing, solidly mounted within the camber plate for direct alignment of the strut shaft and no excess play or deflection. Stage 3 are designed to increase negative camber with their patented 'floating' adjustment that changes camber and caster together. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. Fitment is limited to race-only small diameter coil-over springs (not stock-type). Bearing inserts and adapters included. Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
1997-2003 E39 BMW 525i 528i 530i 540i (for cars with EDC)
1999-2003 E39 BMW M5
1995-2001 E38 BMW 740i 740il 750il (for cars with EDC)
2004-2010 E60 BMW M5
2004-2011 E63 BMW M6

Show More Show Less

KMAC Stage 2 Street/Track Front Adjustable Camber/Caster Plates - E39...

T#:389317

Part#: 193616-2L

Special Order: No Guaranteed ETA

$ 545.00 USD

Add to Wish List

Qty

$ 545.00 USD

Add to Wish List

Location: Front
Type: Street/Track, Stage 2
Bearing: PTFE-lined pillow-ball with thin polyurethane bushing

The Stage 2 KMAC plates are a mixed street/track camber/caster plate meant to be used in a variety of suspensions. Since there is less bushing than on the Stage 1, more noise and vibration will reach the driver. The adjustment design is similar to the Stage 1 with a floating mount that sets camber and caster simultaneously. This design allows maximum range of adjustment since no other hardware interferes with the adjustments. These plates can work on both coil over and stock-stype suspensions. Bearing inserts and adapters included. The Stage 2 camber plates are shorter than a factory mount so may not be suitable for cars will little suspension travel. These are designed mainly for adding negative camber for improved handling and not for camber correction back to stock settings (see Stage 1 kit). Detailed instructions included.

Note: suspensions vary from manufacturer to manufacturer. Turner Motorsport cannot be responsible for fitment issues caused by non-stock or specialized coil-over suspensions. As with any race-derived component, additonal fabrication may be required.

This item fits the following BMWs:
2006-2008 E85 BMW Z4 M Roadster M Coupe

Project Cars

SELECT YOUR BMW

BMW Suspension Parts for BMW 6 Series E64 (2004-2010)

Sub-Categories

KMAC Stage 1 Street Front Adjustable Camber/Caster Plates - E36, E39 ...

Adjustable Front Camber Bushings

Rear Guide Rod - Left or Right - E39, E60, E63, E65

Front Suspension Refresh Kit - Level 1

KMAC Street Rear Adjustable Camber/Toe Bushings - E60 E63 E65 E53 X5 ...

KMAC Stage 2 Street/Track Front Adjustable Camber/Caster Plates - E36...

KMAC Stage 3 Street/Track Front Adjustable Camber/Caster Plates - E36...

KMAC Stage 3 Track Front Adjustable Camber/Caster Plates - E39 540/M5...

KMAC Stage 2 Street/Track Front Adjustable Camber/Caster Plates - E39...

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results