BMW Engine Parts for BMW 7 Series E65 (2002-2008)

All vehicles will lose some degree of performance due to heat soak under the right operating conditions.  Engine management systems constantly monitor operating conditions and modifying parameters based on sensor inputs. BMW integrated the intake air temp sensor in the MAF housing on models such as the E39 M5, and, being sandwiched behind a hot radiator and in some applications next to an even hotter valve cover, this is less than ideal for performance applications. Absorbing excess heat from its surroundings, the MAF can’t shed it fast enough, and the ECU reads an inaccurately high intake air temperature. Compensating for this false hot air measurement, the ECU pulls timing and runs a richer fuel mixture, resulting in a significant loss of torque.

What can you do?  Locate an intake air temp sensor in a location where it can properly measure incoming air temps and where it's less prone to heat soak. Mounting the sensor further away from the heat source and isolating it from the MAF housing, it can both resist the effects of heat soak longer and respond to temperature changes more quickly.  The result is you’ll experience reduced torque loss and more consistent power output when you’re pushing your engine hard. 

The Turner engineering team was initially skeptical of the claimed performance benefits of this modification. They first set out validate the functionality and performance benefit of a temp sensor relocation. Replicating stop-and-go traffic heat soak in a 2001 540i was a simple task in a controlled environment - their dynometer. First the car was heat soaked to simulate being stuck in traffic or moving at low speeds by running the car four times on the dyno with the dyno's cooling fans disabled. The fans were then turned on for three more runs to observe the recovery rate once air flow was reintroduced. The test: following this procedure once with a stock IAT, and once with their relocation kit in place. 

The result? Turner recovered 11lb-ft torque at 2500rpm through use of their relocation kit, with even greater recovery to be found for M5 owners. Here are the heat soak-related torque losses Turner experienced:

Stock IAT location:
18rwtq at 2500rpm
10rwtq at 3000rpm
9rwtq at 3700rpm

Turner IAT Relocation:
7rwtq at 2500rpm
5rwtq at 3000rpm
5rwtq at 3700rpm

**Click here for installation instructions**

The Turner engineering team designed a complete plug and play kit (unlike all other options on the market) that makes for quick, easy, and reversible installation. Weather-sealed connectors keep out the elements, while sheathed wiring offers a clean appearance underhood. With a harness nearly 3 feet long - the Turner IAT relocation kit offers flexibility in positioning, but not too long that you're left with unsightly excess wiring. Turner recommends positioning the sensor in a location away from engine heat, but still within the intake ducting to achieve accurate intake temp readings - such as the far side of the base of the airbox. Vehicles with cold air intakes with cone-style filters can even position the sensor in the end of the filter. Simply drill a hole in your (cool) location of choice and plug in the harness. More information including installation instructions and some good examples of sensor mounting locations can be found in our DIY PDF. 

We include everything you need to relocate your IAT, just select your desired sensor brand below - Genuine BMW or original equipment Beru.

Also the perfect plug-n-play option for anyone looking to upgrade their intake to utilize an Alpha-N tune!

Note for vehicles with M62 engine: applicable to 1999 and up

When we designed this catch we wanted to have the most function options available, the best separation method, and the easiest to service. The Turner engineered catch cans offer a pre-setup design based ion desired flow direction, however this does not limit you to this flow. The inner baffle orientation can be easily adjusted to flow in both directions in case you decide to move this catch can to a different vehicle. A 4 chamber system  baffle system inside the catch can was engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can. Having a closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation.

Our catch can was also designed with the idea that the cans fill level can easily be checked with a top mounted dipstick and an optional use bottom drain hole. The drain hole can be used with a valve and hose to be mounted at a lower area of the vehicle so when you're doing an oil change you can drain the catch can.

Features:

• 6061-T6 billet machined body, anodized black for lasting protection and appearance
• Strategically positioned 4 chamber baffle system maximizes oil / air separation 
• Knurled and black anodized oil dipstick makes inspecting oil volume of reservoir clean and simple
• Sealed with a pre-installed viton O-Ring
• Includes 2.5mm allen key to remove baffle plates for cleaning
• Engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can
• Closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation
• Optional use drain hole (valve and hose sold separately, watch for our model specific drain kits!)

The 12 Piece 3/8" Drive Magnetic Spark Plug Socket Set from VIM Tools is expertly designed for effortless spark plug removal and installation. Each of the 12 magnetic sockets in this set features a satin finish and is equipped with magnetic rings to securely hold the spark plug in place during use.

The sockets are neatly organized in a black and green EVA foam tray with clearly labeled sizes for quick identification.

The set includes a variety of socket types—metric, SAE, 6-point, 12-point, standard length, extra deep, thin wall, universal joint, and dual drive—making it versatile enough for use in a wide range of domestic and imported vehicles.

The spring-loaded universal joint design allows for easy access to spark plugs in tight or confined spaces, while the knurling on the socket body provides extra grip for hand turning. The 12-point 14mm sockets are easily distinguishable by their double knurling, saving you time on the job. Additionally, the dual drive feature lets you use either a 3/8" drive ratchet or a wrench for added flexibility.

Key Features:

• Magnetic Ring Inserts: Securely hold spark plugs in place for easy removal and installation.
• Versatile Socket Set: Includes metric, SAE, 6-point, 12-point, standard length, extra deep, thin wall, universal joint, and dual drive sockets.
• Spring-Loaded Universal Joint: Provides easy access to spark plugs in confined spaces and prevents loosening.
• Knurled Grip: Single and double knurling on socket bodies for better hand-turning control.
• Convenient Organization: Sockets are laid in a black and green EVA foam tray with labeled sizes for quick identification.
• Dual Drive Capability: Allows use with both a 3/8" drive ratchet and a wrench.

Includes:

**Note: All sockets are magnetic and 3/8" Drive**

• 9/16"
• 5/8"
• 14mm
• 13/16"
• 16mm Thin Wall 6 Point
• 14mm Thin Wall 12 Point
• 9/16" Spring-Loaded UJ
• 5/8" Spring-Loaded UJ
• 14mm Spring-Loaded UJ
• 9/16" Extra Deep 6" OAL
• 14mm Extra Deep 6" OAL 12 Point