BMW Suspension Parts for BMW E90 M3 S65 4.0L

Ohlins Racing has a long history dating back to 1976 of providing premium motorcycle and automotive suspension systems to numerous racing teams, individual racers, and OE brands such as BMW Motorsport, Audi, Lamborghini. Pagani, Ducati and Kawasaki. Over time, thanks to extensive R&D, testing, and tuning, their products have evolved into some of the highest quality suspension systems in the world, providing years of flawless operation on both the street and the track.

Ohlins' latest automotive suspension system, the DFV (Dual Flow Valve) Road and Track Coilover Kit, has bridged the gap between comfortable stock suspension and track focused coilover kits. These kits provide a ride that glides over typical bumps and dips in the road, all without the typical hard rattle and harsh feel of usual coilovers, and turn in tight and maintain tire grip and traction in corners significantly better than stock suspension ever could. This is all thanks to the spring rate chosen and Ohlins and their signature Dual Flow Valve. The DFV maintains comfort and agility by giving the same characteristics for both rebound and compression, allowing the wheel and tire to maintain constant contact with the road/track for maximum control.

The Dual Flow Valve works by controlling shock fluid flow based on resistance and impact velocity. This is controlled in both compression and rebound, giving the quick shock operation that helps maintain traction. At low shaft travel speeds, oil flows mostly through the shaft jet bleed. At higher shaft speeds, oil flows mostly through the compression/rebound ports in the piston. At very high shaft speeds, or during sudden accelerations from potholes or large bumps in the road, oil can then escape through the ports in the DFV, absorbing a large amount of energy that would otherwise throw off the balance and control of the vehicle and keeping the tire planted firmly on the ground. With all three compression and rebound ports working together according to pressure and shaft speed, the result is the notorious premium suspension feel that only Ohlins can offer.

In addition to managing the rebound and compression control, coilovers must also properly address heat changes in the shock oil. As the shock is pushed harder and longer, the oil quickly heats up due to friction and compression, and the oils flow characteristics change. The hotter the oil is, the easier it is for it to travel through ports and valves. To prevent this typical fade in control, Ohlins has implemented a temperature controlled needle bleed valve system that will expand as temperatures rise, slowly increasing restriction in the fluids flow through the valve gap. This produces a consistent dampening rate that maintains the vehicle's suspension characteristics lap after lap, turn after turn, no matter how hard you push your suspension's capabilities.

Features:

• DFV (Dual Flow Valve)
• Adjustable ride-height
• Fully rebuildable
• Corrosion salt spray tested (ISO 9227)
• Includes hardware and installation instructions
• 2 year Limited Warranty

Specs:

• Front Spring Rating: 343 lbs/in  ( 6 kg/mm)
• Rear Spring Rating: 686 lbs/in  ( 12 kg/mm)

*Now available are optional EDC Cancellation Modules that will prevent any lights or issues with suspension control systems. Turner Motorsport recommends purchasing these in addition to the suspension kit to get the most out of your Ohlins suspension system.

Find installation instructions HERE.
Find owner's manual HERE.

Fits the following BMWs:
2008-2013 E9X BMW M3

The öhlins EDC Cancellation Kit for Road & Track deactivates control lamps and error reports when electronically adjustable OEM suspension is replaced by a mechanical system. The cancellation kit is just plugged into the original suspension controls. No further programming is needed.

Included:

• 1 Cancellation Kit
• Installation material (if needed)
• Mounting instruction

You can find mounting installation instructions HERE.

Fits the following BMWs:
2008-2013 E9X BMW M3

Upgrade your vehicle's performance with our replacement rear lower control arm inner bushings. These bushings feature a low-friction, PTFE-lined spherical bearing, enhancing cornering grip and dynamic geometry. By eliminating OEM bushing deflection and binding, our product preserves camber and toe geometry during bumps. Enjoy improved stability and handling precision, thanks to the maintenance-free FK bearings with PTFE linings. Crafted from high-quality materials including 6061-T6 aluminum and FK PTFE-lined spherical bearings, our bushings ensure durability and NVH reduction. Experience the benefits of enhanced performance and reliability with our premium upgrade.

Key Advantages:

Enhanced Rear Cornering Grip Elimination of OEM Bushing Deflection and Binding Improved Dynamic Geometry, Stability, and Handling Precision Maintenance-Free FK Bearings, Manufactured in the US, with PTFE Linings Materials Used:

6061-T6 Aluminum Bearing Shells and Spacers FK PTFE-Lined Spherical Bearings (F1 Specification, Self-Cleaning)

SPL Parts is a performance suspension manufacturer that designs and tests their products all in-house here in the USA. Additionally, all materials used are sourced from American suppliers to ensure consistently high quality products. SPL Parts products are all constructed using chromoly seamless straight tubing, DOM mandrel bent tubing, and 6061 and 2024 aluminum for high strength and quality. All TIG welding and CNC machining is also done locally by professional welders and machine shops to meet exact quality standards and tolerance specifications. For anything from racing to street driven needs, SPL Parts offer an amazing line of premium quality products that are perfect to get your car back in spec.

Factory BMW eccentric bolts only allow for small toe adjustments and often slip under hard cornering, effectively changing your alignment. SPL eccentric lockout kits eliminate stock eccentric bolts - you must have adjustable rear toe arms to utilize this kit in your setup; 

Technical Specifications:

• CNC machined from 6061 aluminum
• CAD plated grade 10.9 hardware
• Include washers and bolts for both sides of your vehicle.
• Made in the USA!

Fits the following BMWs:
2006-2013 E9X BMW RWD Sub-Models
2008-2013 E82 BMW All Submodels

Exposure to the elements and stress/pressure can lead to failing and splitting subframe bushings. Ensure your subframe is mounted perfectly steady to prevent vibrations, knocks, suspension issues, and potential damage to the body of the vehicle or suspension components. OEM Lemforder is the perfect replacement to make sure that everything is mounted properly.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMW Chassis:
E82, E90, E92, E93

When an E9X is lowered beyond the limits of just lowering springs, the rear wheels toe-in excessively. This excessive rear toe leads to premature wear, that many people attribute to an increase in negative camber. It has become a common belief that an extremely low vehicle will wear the tires wrong as a matter of consequence. It has become standard practice to go as low as you can and proceed to replace your tires every five to ten thousand miles. Whats more is that when the vehicle reaches a certain ride height, the factory arms become maxed out and there is no way to compensate and dial in the proper toe. You're left with an improperly aligned vehicle that is in effect worse off than it was with the stock suspension installed.

This is not only uneconomical but improper and unsafe. ECS Tuning is proud to offer a solution for this problem in the form of Rogue Engineering E9X adjustable rear toe arms. These arms allow for greater toe adjustment on vehicles that have been lowered with a coilover suspension. With the toe set properly the tires can contact the road properly this maximizes grip and minimizes wear. 

Features:

• 100% machined and anodized, 6061-T6 lightweight aluminum arms
• High-strength, 3-piece, rod end (with carbon fiber reinforced, PTFE race) offers longer life for street compared to standard rod ends
• SEALS-IT Rod end seals keep dirt, water, and other contaminants out
• Rod ends feature grease fittings, to allow for rod end serviceability.
• Lighter than stock!  (Stock is 875g, RE arms are 640g)
• Extremely easy installation and adjustment (your alignment shop will LOVE you!)

These SPL Parts adjustable rear toe arms replace OEM part number 33322283549

SPL Parts is a performance suspension manufacturer that designs and tests their products all in-house here in the USA. Additionally, all materials used are sourced from American suppliers to ensure consistently high quality products. SPL Parts products are all constructed using chromoly seamless straight tubing, DOM mandrel bent tubing, and 6061 and 2024 aluminum for high strength and quality. All TIG welding and CNC machining is also done locally by professional welders and machine shops to meet exact quality standards and tolerance specifications. For anything from racing to street driven needs, SPL Parts offer an amazing line of premium quality products that are perfect to get your car back in spec.

When lowering your vehicle, toe alignment is thrown off. These SPL adjustable toe arms offer a wide range of toe adjustment and are a significant improvement over stock, eliminating suspension deflection and increasing handling response thanks to the FK Bushings rod ends that are Teflon lined.

Technical Specifications:

• Gundrilled 2024 Aluminum Links to reduce unsprung weight
• 6061 Aluminum Clamps and Heim Joint Spacers
• Titanium Socket Head Cap Screws
• Rotating clamp design allows for easy access to lock down your alignment settings
• Low friction 3 piece Teflon lined FK Heim joints/rod ends made in Connecticut
• Made in the USA!

Fits the following BMWs:
2006-2013 E9X BMW M3
2008-2013 E8X BMW 1 M

BMW E9X M3/E82 1M Inner Lower Tension Arm Bearing is engineered to elevate suspension performance with precision and durability. Developed by Fall-Line, known for their championship-level race cars and premium suspension components, this bearing is a significant upgrade over factory rubber bushings. Designed for motorsport applications, it incorporates FK spherical bearings for enhanced strength and longevity.

• Superior Performance: Provides a notable improvement over OEM rubber bushings for enhanced control and feedback.
• Durable Construction: Features the largest FK spherical bearings available, ensuring long-lasting reliability.
• Enhanced Control: Eliminates rubber components to offer better control over tire behavior and increased driver confidence.
• Robust Design: Equipped with stainless steel spiral locks for 360 degrees of clamping force to secure the bearing firmly.
• Long-Lasting: Outperforms OEM rubber variants, reducing the need for frequent replacements.
• Precision Engineering: CNC machined from high-quality materials in the USA for exact fit and superior performance.

Bushings tends to wear over time and split or even break free from the internal sleeve, causing excessive movement and sloppy control feel. OEM Lemförder bushings are the perfect option to restore suspension back to day 1 quality.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMW Chassis:
E82 1M Coupe,E82,E90,E92,E93,F80 M3,F82 M4,F83

Strut mounts can begin to wear and fail over time, causing a knock in the suspension to occur. Replace yours with a high quality OEM Lemförder replacement to ensure a tight, noise-free ride.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!