BMW Brakes & Brake Parts for BMW E90 M3 S65 4.0L

This caliper carrier is secured to the steering knuckle and aligns the caliper to the rotor.

Genuine BMW Brake Carrier
This item fits the following BMW Chassis:
E82 1M Coupe,E82,E90,E92,E93

When the brake master cylinder goes bad, your brakes will no longer operate as they should. You might get a brake warning light on your dashboard and the brake pedal might sink down and not return to its normal position. When this occurs, be sure to replace that master cylinder. The brake master cylinder is bolted to the Brake Booster with two bolts.

Genuine BMW Brake Master Cylinder
This item fits the following BMW Chassis:
E82 1M Coupe,E82,E90,E92,E93

RSL19 A favorite of BMW's Motorsport engineers, the Pagid RSL19 compound is an endurance pad based on the RS14 Black but with less friction to improve modulation and low pedal effort. These pads work best in a heat range up to 1,100* F. The combination of friction levels, fade stability, and long life for pads and rotors makes this a favorite for club and HPDE drivers. 

This kit includes both the Front and Rear brake pads.

This item fits the following BMWs:
2011+ E82 BMW 1M Coupe
2008-2013 E9X BMW M3

As you depress the brake pedal, your pedal linkage causes a shaft to move forward in response to your foot, and as this shaft moves forward, it interacts with the brake booster and master cylinder. The brake booster contains a diaphragm that separates its interior into two parts, with both in a partial vacuum. As the brake pedal is depressed, it causes a valve inside the booster to open, which in turn allows air into one side of the booster. This difference in pressure on one side helps to push the piston inside the brake master cylinder forward in response to the brake pedal, which in turn slows and stops your vehicle.

This item fits the following BMW Chassis:
E82 1M Coupe,E82,E90,E92,E93 M3

BRAKE CALIPER PISTON TOOL SET:

The Schwaben 18-piece disk brake retractor tool kit screws brake caliper pistons back into their bores to make room needed for new brake pads. An essential tool for working on calipers with threaded pistons, the kit comes with both right-hand and left-hand thread screw jacks, press plate, and 15 different diameter press disks to fit a wide variety of vehicles, both import and domestic, including Audi, BMW, Ford, GM, Honda, Mazda, Mitsubishi, Subaru, Toyota, Volkswagen and others.

Made of 100 percent chromalloy steel for strength, durability, and long service life.

PROTECTA SOCKET SET:

Protecta socket are used to keep ugly scratch marks from showing up after torqueing down wheel lugs.

Features:

• Coated six-point deep-well impact sockets 
• Color coded mar-free exterior coatings that prevent nicks and scratches left by plain metal sockets
• 17mm, 19mm and 21mm Sockets included

Use these with your breaker bar or impact gun to remove the tightest wheel bolts and lug nuts: when reinstalling wheels, use them to final torque wheel fasteners to factory specifications.

Combine these with our torque limiting sockets and the Schwaben ½-inch torque wrench for a complete wheel fastener solution.

CALIPER HOOK SET:

• Tired of messing with bent coat hangers or bungee cords to hang your calipers up and out of the way when performing brake maintenance? These hooks make working on your brakes easier by letting you hang your calipers with ease, no more fighting with the bungee cords or zip ties to hold the caliper just right or having to make your own "custom" hooks with wire.
• Holds brake calipers out of the way while working on brakes
• Also use to hang other automotive parts and tools while working on your vehicle.
• Stronger than zip ties or wire.
• Save the brake hose by not hanging caliper by hose.
• Made of  thick steel for strength and durability. length is 8"

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Schwaben Professional Mechanic's Work Gloves provide exceptional hand protection with a perfect balance of durability and comfort.

Designed for precision, these gloves offer high dexterity, making it easy to handle even the smallest parts. The tailored elastic cuff with a hook-and-loop closure ensures a secure and comfortable fit.

The textured latex coating on the palm and fingertips delivers superior grip and tactile feedback, while the breathable spandex backing and knit top allow for all-day comfort.

The durable synthetic leather palm enhances longevity, and the unique graphic design reflects the drifting culture of Euro car enthusiasts.

Note: See manufacturers information tab for sizing chart.

Key Features:

• High Dexterity: Perfect for picking up small parts with ease.
• Secure Fit: Tailored elastic cuff with a hook-and-loop closure.
• Enhanced Grip: Textured latex coating on palm and fingertips.
• All-Day Comfort: Breathable spandex backing and knit top.
• Durable Design: Synthetic leather palm for extended wear.
• Unique Style: Graphic design inspired by the drifting culture of Euro owners.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.