BMW Brakes & Brake Parts for BMW 3 Series E90 (2006-2011)

RSL19 A favorite of BMW's Motorsport engineers, the Pagid RSL19 compound is an endurance pad based on the RS14 Black but with less friction to improve modulation and low pedal effort. These pads work best in a heat range up to 1,100* F. The combination of friction levels, fade stability, and long life for pads and rotors makes this a favorite for club and HPDE drivers. 

This kit includes both the Front and Rear brake pads.

This item fits the following BMWs:
2011+ E82 BMW 1M Coupe
2008-2013 E9X BMW M3

The latest in the Yellow line takes all of the RSL29 characteristics and adds a bit more aggressive behavior. Friction levels go up for more initial bite and better fade resistance. Modulation and release stays close to RSL29 levels. Pad and rotor wear is a little more than on the previous Yellows but still within reasonable levels and the RSL1 is still considered an extended endurance pad. Its development stemming from GT classes at Le Mans and Nürburgring.

Since Pagid pads tend to "out-gas" we recommend using these pads with a new gas-slotted or cross-drilled rotor for the best performance. Pagid brake pads are not compatible with previously used rotors, especially if used with a carbon or Kevlar based race pad.

This item fits the following BMWs:
2008-2013 E82/88 BMW 135i, 128 with BMW Performance caliper conversion
2006-2009 E9X BMW Submodels with BMW Performance caliper conversion

BRAKE CALIPER PISTON TOOL SET:

The Schwaben 18-piece disk brake retractor tool kit screws brake caliper pistons back into their bores to make room needed for new brake pads. An essential tool for working on calipers with threaded pistons, the kit comes with both right-hand and left-hand thread screw jacks, press plate, and 15 different diameter press disks to fit a wide variety of vehicles, both import and domestic, including Audi, BMW, Ford, GM, Honda, Mazda, Mitsubishi, Subaru, Toyota, Volkswagen and others.

Made of 100 percent chromalloy steel for strength, durability, and long service life.

PROTECTA SOCKET SET:

Protecta socket are used to keep ugly scratch marks from showing up after torqueing down wheel lugs.

Features:

• Coated six-point deep-well impact sockets 
• Color coded mar-free exterior coatings that prevent nicks and scratches left by plain metal sockets
• 17mm, 19mm and 21mm Sockets included

Use these with your breaker bar or impact gun to remove the tightest wheel bolts and lug nuts: when reinstalling wheels, use them to final torque wheel fasteners to factory specifications.

Combine these with our torque limiting sockets and the Schwaben ½-inch torque wrench for a complete wheel fastener solution.

CALIPER HOOK SET:

• Tired of messing with bent coat hangers or bungee cords to hang your calipers up and out of the way when performing brake maintenance? These hooks make working on your brakes easier by letting you hang your calipers with ease, no more fighting with the bungee cords or zip ties to hold the caliper just right or having to make your own "custom" hooks with wire.
• Holds brake calipers out of the way while working on brakes
• Also use to hang other automotive parts and tools while working on your vehicle.
• Stronger than zip ties or wire.
• Save the brake hose by not hanging caliper by hose.
• Made of  thick steel for strength and durability. length is 8"

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

BRAKE CALIPER PISTON TOOL SET:

The Schwaben 18-piece disk brake retractor tool kit screws brake caliper pistons back into their bores to make room needed for new brake pads. An essential tool for working on calipers with threaded pistons, the kit comes with both right-hand and left-hand thread screw jacks, press plate, and 15 different diameter press disks to fit a wide variety of vehicles, both import and domestic, including Audi, BMW, Ford, GM, Honda, Mazda, Mitsubishi, Subaru, Toyota, Volkswagen and others.

Made of 100 percent chromalloy steel for strength, durability, and long service life.

PROTECTA SOCKET SET:

Protecta socket are used to keep ugly scratch marks from showing up after torqueing down wheel lugs.

Features:

• Coated six-point deep-well impact sockets 
• Color coded mar-free exterior coatings that prevent nicks and scratches left by plain metal sockets
• 17mm, 19mm and 21mm Sockets included

Use these with your breaker bar or impact gun to remove the tightest wheel bolts and lug nuts: when reinstalling wheels, use them to final torque wheel fasteners to factory specifications.

Combine these with our torque limiting sockets and the Schwaben ½-inch torque wrench for a complete wheel fastener solution.

CALIPER HOOK SET:

• Tired of messing with bent coat hangers or bungee cords to hang your calipers up and out of the way when performing brake maintenance? These hooks make working on your brakes easier by letting you hang your calipers with ease, no more fighting with the bungee cords or zip ties to hold the caliper just right or having to make your own "custom" hooks with wire.
• Holds brake calipers out of the way while working on brakes
• Also use to hang other automotive parts and tools while working on your vehicle.
• Stronger than zip ties or wire.
• Save the brake hose by not hanging caliper by hose.
• Made of  thick steel for strength and durability. length is 8"

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Upgrade your braking with this limited-time Doorbuster package! Featuring ECS 2-Piece Front Brake Rotors and Exact-Fit Stainless Steel Brake Lines for the front of your BMW, this package reduces weight, improves brake cooling, enhances pad contact under heavy deceleration, and allows for better brake pedal feedback.

ECS 2-PIECE FRONT BRAKE ROTORS

These 2-piece floating rotors help dissipate heat better than a standard cast iron rotor and are also lighter for less unsprung weight. Managing heat in the brake system is vital to braking performance, especially on the track or when driven hard. It's why your brake rotors have internal vanes that vent heat as the rotor spins. These 2-piece ECS rotors feature an outer cast iron friction surface ring that is separate from the aluminum center hat. This allows better airflow through the vanes and for the friction ring can expand as it gets hot. The rotors are also cross-drilled for better ventilation and slotted to improve brake pad performance.

ECS 2-Piece Rotors feature:

• Aluminum hats for light weight
• Heat-treated cast iron friction rings
• 2-piece assembly improves brake cooling
• Anti-corrosion coating on non-friction surfaces and hard anodizing on rotor hat

These are the same size as the stock rotors so your stock caliper and mounting bracket will fit and there will be no clearance issues with your wheels or to other components. Stainless steel rotor retaining screws are included. You can use these with any brake pad.

ECS EXACT-FIT STAINLESS STEEL BRAKE LINES

ECS Exact-Fit stainless reinforced brake lines ensure consistent and reliable stopping power - ECS's stainless steel lines help maintain consistent brake pressure, while capitalizing on the inherent benefits of stainless steel.

If you are already planning on replacing your factory lines due to your vehicle's age, ECS's stainless steel brake lines are a great solution. Factory rubber lines expand under heavy braking, even when new. This causes sloppy pedal feel and overall poor performance. ECS reinforces their exact fit lines with braided stainless steel mesh, creating expansion resistance - this enhances pedal feel and improves performance. Their red polymer coating provides protection from the elements and abrasion that commonly affect brake lines.

ECS Exact-Fit stainless lines are manufactured to comply with DOT (U.S. Department of Transportation) FMVSS 106 standards. All lines are made on dedicated, DOT-compliant brake equipment, with every line being tested to 3000 psi prior to shipment.

The caliper sliding bolts are one of the most overlooked wear items in your braking system. Subjected to constant motion and often without adequate lubrication the guide bolts see a lot of wear and tear. Factory BMW caliper guide bolts are very expensive from the dealer - these 304 stainless steel bolts are less than half the price and provide outstanding resistance to corrosion and wear. They are manufacturered with tighter tolerances than the factory bolts too.

Price is per bolt unless noted (2 required per caliper).

Enter your vehicle info for specific fitment information.