BRAKE BLEEDER:

We know bleeding brake alone is not only no fun, but much more complicated than it needs to be. Having a pressure bleeder give you the ability to keep the pressure on the brake system while you go under and crack open the bleeder screws to relieve the air pockets.

Features:

• Holds a full 3-Liters (3.17 qts) of brake fluid
• Easy to read 0-30 lbs pressure gauge built into the tank top
• Pressure relief valve for safe release of pressure
• 40" hose with detachable swivel fitting

Note:

• Do not exceed 20 PSI
• LIFETIME REPLACEMENT

Includes:

• 3 Liter (3.17 qts) storage tank
• Pressure cap with 0-30 lb gauge and pressure relief valve
• 40" hose
• Dual preventative fittings on the hose, featuring a chrome quick coupler on one end to snap onto the master cylinder cap and a detachable swivel fitting on the other end

Note:

• Recommend working at 10 PSI
• Dimensions for cap seal: 12x21x4 mm
• LIFETIME REPLACEMENT

CATCH BOTTLE:

Keep your fluid's off the floor and into our catch bottle.  The bottle has fluid level markings from 0.2L to 0.7 liter. This feature allows you to measure how much fluid you have sent thru the system.  Our bleeder bottle features an expandable/collapsible top portion for easier storage. Gasket in cap prevents leakage. Tubing is extra long at 24" from cap to nipple. Flexible hose can be pushed down into bottle for storage when done. Bottle now features a handy hanger bracket to hang bottle from bottom of car.

CALIPER HOOK SET:

Tired of messing with bent coat hangers or bungee cords to hang your calipers up and out of the way when performing brake maintenance? These hooks make working on your brakes easier by letting you hang your calipers with ease, no more fighting with the bungee cords or zip ties to hold the caliper just right or having to make your own "custom" hooks with wire.

• Holds brake calipers out of the way while working on brakes
• Also use to hang other automotive parts and tools while working on your vehicle.
• Stronger than zip ties or wire.
• Save the brake hose by not hanging caliper by hose.
• Made of  thick steel for strength and durability. length is 8"

BILLET ALUMINUM CAP:

This aluminum cap with 90 degree swivel will work with our T#363245 Euro bleeder or our T#366970 3-Liter Multi-functional Fluid Pump Kit.

Features an all aluminum 45mm cap with quick coupler nipple.

BLEEDER WRENCH:

Finally, a bleeder wrench with just the right angle to open the bleeder screw without having to spend all that time removing each wheel from your car.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

These are completely stock brake hoses made to fit your vehicle exactly. Ends have the same thread pitch as the stock unit and length is perfect. Designed to perform just like stock, this line will get your brakes working perfectly again. A high-quality replacement for any damaged or swelled hose.

If you are replacing your brake lines, you will need to get some fluid. While bleeding the replacement lines, make sure to put in quality, system compatible fluid to give your vehicle the best in braking.

Genuine BMW Brake Hose Rear
This item fits the following BMW Chassis:
E82 1M Coupe,E82,E90,E92,E93

The RSL29 pad is an endurance racing compound with long life and great wear characteristics. It has stable friction over a broad temperature range which makes them a very easy to use and predictable braking pad in a lot of environments. An evolution of the RSL19 endurance pad designed for more advanced drivers. This compound combines the outstanding wear rate of the RSL19 with a slightly higher coefficient of friction and initial bite. RSL29 also features improved hot fade resistance over the RSL19. In addition to the endurance racing, this pad will also be found in GT and VLN classes and Touring Cars (including our own E46 World Challenge cars). BMW has been using Pagid Yellow pads on their Nurburgring test vehicles and Ring Taxi for years.

This is the set of Rear pads.

This item fits the following BMWs:
2004-2010 E60 BMW 535i 545i 550i M5
2004-2011 E63 E64 BMW 645ci 650i M6
2011+ E82 BMW 1M - Coupe
2008-2013 E90 BMW M3 - Sedan
2008-2013 E92 BMW M3 - Coupe
2008-2013 E93 BMW M3 - Convertible