BMW Intake Parts for BMW 3 Series E90 (2006-2011)

The intake boot is a regular issue especially for BMW's, nearly all vehicles have a boot manufactured from rubber with an accordion section in the design for flexibility. This flexible section is typically where the failure comes from leading to vacuum leak engine codes, rough idle, and increase fuel consumption. 

When you upgrade to a Turner silicone intake boot you get a perfect fit that will not only outlast the OE design (meaning any vacuum leaks and rough idle), while also smoothing out airflow within the intake tract. This boot also eliminates the factory intake resonator giving your engine a much more aggressive sound under the hood especially at higher rpm. Available in black or Turner blue color, our intake boot offers either a pop of color or a cohesive, complementary look in your engine bay.

The Turner Motorsport silicone intake boot is manufactured with 5 layers of wire reinforced silicone to prevent collapse under load. Engineered in-house utilizing 3D scanning technology, this boot offers perfect fitment with the factory air box and either single stage or three stage (high output N52) intake manifolds.

Install as a standalone reliability improvement or in addition to our three stage intake manifold and Turner performance tune (available here).

Replaces OE intake boot 13717536004.

Features:

• 5 layers of wire reinforced silicone
• Perfect fitment with factory airbox
• Compatible with single stage or three stage manifold
• Installation hardware included

This item fits the following BMWs:
2008-2013 E82 E88 BMW 128i Coupe Convertible
2006-2011 E90 BMW 325i 325xi 328i 328xi 330i 330xi - Sedan
2007-2011 E91 BMW 325i 325xi 328i 328xi - Touring Wagon
2007-2013 E92 BMW 328i 328xi - Coupe
2007-2013 E93 BMW 328i - Convertible

Full carbon fiber intake to increase flow, performance and aesthetics! Dual inlet design for maximized air flow while retaining the OEM+ fitment.

The most common N55 intake utilizes a short plastic tube and oversized cone filter; it is your job to have better taste than the common N55 owner. This carbon intake changes the whole image of the N55 engine while maintaining a flow of cool air and added induction noise. With a dual inlet design the engine bay retains its functionality while adding a second inlet to provide your engine with improved air flow and sound. To ensure the engine gets the coolest air possible the second inlet is located in the "sweet spot" on the cold side of the engine for the lowest intake air temps and most air flow possible. The cone filter features a bellmouth velocity stack filter that creates the satisfying flutter after letting of the throttle.

Our Turner Carbon Fiber Intakes start with a 3D scan of the factory intake and engine bay. Engineers use the 3D imaging of the chassis to design the intake in SolidWorks modeling software. Using a Flow Bench, the Intake is then airflow tested against the factory intake, to ensure optimal airflow improvement against stock. The final product is a beautiful and functional Carbon Fiber Intake, CAD designed for perfect integration with the OEM inlet ducting and stock mounting locations and proven to flow better than factory.

Key Benefits:

Increased flow over the factory intake
Carbon fiber airbox and intake tube with gloss clear coat for UV protection
CAD-Designed for perfect Integration
Custom high flow air filter specially designed to to pair with the carbon fiber airbox
Kit Contents:

Carbon Intake Tube
Full Carbon 2 Piece Airbox
Bellmouth Velocity Stack Cone Filter
Billet Turbo Inlet Adapter
Silicone Coupler
Hardware For Installation
Design:

- Carbon Fiber Intake Tube

Carbon inlet tube featuring a smoother interior without corrugations for a smooth flow path.
Integrated carbon flange allows secure mounting of the tube to the carbon air boxes.
Intake tube is manufactured using 2x2 twill weave carbon fiber for a great look in the engine bay.
Gloss finish clear coat for UV protection.
4-ply reinforced silicone coupler and 6061-T6 black anodized aluminum flange that utilizes the factory o-ring and retaining clip.
- Air Box

Carbon fiber airboxes are manufactured using 2X2 twill weave carbon fiber and protected with a gloss finish clear coat for UV resistance to match the intake tube.
Air box mounts in stock location with supplied hardware.
- Air Filter

Conical hi-flow reusable air filter; featuring 8 ply oiled cotton gauze construction to maximize filtration efficiency.
Bellmouth (velocity stack) filter flange inlet to reduce turbulence in order to maximize flow.
Product Development:

Turner N55 Intake System was designed, engineered, tested and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer and rigorous long term product testing. Performance data metrics are collected utilizing Mustang AWD 500 SE in ground dyno and in-house Superflow SF-750 Flowbench.

Fitment:

E82 135i N55
E88 135i N55
E84 X1 35i
E90 335/xi N55
E92 335/xi N55
E93 335/xi N55

Over 13 CFM more airflow than factory intake plenum! Beautiful Carbon Fiber construction with a roaring induction sound!

At Turner Motorsport, all our Carbon Fiber Intake Systems are top-of-the-line custom-engineered products that we developed in house. Our engineers took it upon themselves to design a prettier, cost effective Carbon Fiber Intake Plenum for S65 owners to compliment our E9x Carbon Fiber Intake System while retaining OEM features. Our S65 Carbon Intake Plenum is no different. Our Carbon Fiber Intakes start with a 3D scan of the factory intake and engine bay. Our Engineers use these 3D images of the chassis to design the intake plenum in SolidWorks modeling software. Using a Flow Bench, the Intake Plenum is then airflow tested against the factory intake, to ensure optimal airflow improvement against stock. The final product is a beautiful and functional Carbon Fiber Intake Plenum, CAD designed for perfect integration with the OEM inlet ducting and stock mounting locations. Our Carbon fiber Intake trumpets flow an average of 13 CFM over the stock BMW intake.

Our E9X M3 S65 Carbon Fiber Intake Plenum is made from 100% high grade prepreg 2x2 twill weave carbon including the internal trumpets, this plenum replaces the OEM plastic plenum allowing the naturally aspirated BMW V8 engine to generate more inductions sounds taking the driving experience of the M3 to a whole new level. The raw V8 rumble gives the M3 an almost CSL like sound and is truly an intoxicating experience. We went through several iterations using different carbon thicknesses to fine tune the sound and the resulting plenum generates an almost unbelievable induction volume and tone.

Our Carbon Fiber Intake Plenum can be used with the OEM airbox or any aftermarket intake system. Paired with our E9X M3 intake system, you're sure to upgrade the look and sound of your S65 engine.

Design Features and Benefits:

CAD designed Intake System for perfect integration with the OEM connections and stock mounting locations.
Carbon intake is manufactured using 2X2 twill weave carbon fiber for a great look in the engine bay.
Plenum is protected by a gloss finish clear coat for UV protection.
Uses OE intake temp sensor and hose locations
Provides same fitment as OE intake
Performance:

Carbon fiber Intake trumpets flow an average of 13 CFM over the stock BMW intake.
\

Maximize performance and reduce intake air temperatures on your E90 335d with the Turner Motorsport Stepped Intercooler. Designed as a direct-fit upgrade for the factory intercooler, this high-efficiency unit increases charge air volume and airflow, helping your diesel-powered BMW run cooler, stronger, and more efficiently.

Cooler air is denser air, and denser air means more power. By reducing intake air temperatures (IATs), this upgraded intercooler allows your M57 engine to pack in more air and fuel per cycle, translating to improved performance across the RPM range.

Engineered for performance and durability, the Turner stepped intercooler features cast aluminum end tanks and a bar-and-plate core design, offering superior thermal efficiency and structural strength. Compared to the stock unit, it delivers a 65% increase in both frontal surface area and internal cross-sectional flow, ensuring better heat dissipation and reduced pressure drop. All of this performance comes in a lightweight package under 20 lbs.

Finished in a stealthy black coating with laser-etched Turner logos, this intercooler not only performs but looks good doing it.

Key Features:

Designed specifically for the E90 335d (M57 engine)
Cast aluminum construction for durability
High-efficiency bar-and-plate core
65% increase in frontal and cross-sectional area
Significantly lowers IATs for improved power and reliability
Reduced pressure drop for more consistent boost delivery
Lightweight design – under 20 lbs
Dimensions: 520mm wide × 200mm tall × 150mm deep
Direct bolt-on installation – no modifications required
If you're looking to get the most out of your E90 335d, the Turner Motorsport Stepped Intercooler is a must-have upgrade for your turbo diesel intake system.

Upgraded replacement for your crankcase vent hose P#11127584128 featuring upgraded silicone, stainless steel clamps, and new OE connectors and seals.

Enhance your BMW N55 engine with our Silicone Crank Case Vent Hose, a premium replacement for the fragile, failure-prone factory hose. Over time, the stock plastic hose deteriorates due to constant exposure to heat and oil, leading to cracks and leaks. Our solution? A high-quality silicone hose engineered for superior durability and long-term reliability.

To further enhance performance, we’ve lined the hose with fluorosilicone, providing exceptional resistance to oil and chemical degradation. Designed in-house using advanced CAD modeling and 3D scanning, this hose offers a precise OEM fit while eliminating the common weaknesses of plastic construction.

Each kit includes stainless steel hose clamps for a secure, hassle-free installation. Whether you’re replacing a worn-out CCV hose or upgrading for added peace of mind, this premium solution ensures your BMW N55 runs smoothly and efficiently for years to come.

Features:

Arrives preassembled with new OE fittings and seals
Direct OEM Fit – Retains factory hose dimensions while eliminating reliability issues.
High-Performance Silicone – Resists heat-related wear for long-lasting durability.
4-Ply Fluorosilicone Lining – Superior protection against oil and chemical exposure.
Stainless Steel Clamps Included – Secure installation and extended service life.
Give your BMW N55 the reliability it deserves—upgrade to the ECS Tuning Silicone CCV Hose today!

All of the tuning in the world is only as good as the weakest link. More boost in your 135/335 is great! But you will soon learn that some of the factory hardware is not up to the task of handling that extra pressure. One of the first things to fail and cause a boost leak are the factory boost diverter valves. This allows boost to "leak" out of the intake stream and a loss of power from the engine. This ECS Tuning chargepipe upgrade includes a blow-off valve in place of the factory diverter valves. The BOV is higher quality than the diverter valves and will exit intake air to the outside instead of putting it back through the turbo system (which will reduce strain on the turbos). This aluminum chargepipe is also much more robust than the stock plastic factory pipe and the connection to the throttle body is stronger, eliminating another failure point of the stock pipe.

Built-in 1/8" NPT ports allow you to run an additional methanol injection kit (bungs included if you don't want use the ports).

This is a complete kit that includes everything you need to replace the factory chargepipe and diverter valves -

powedercoat chargepipe ECS Tuning blow-off valve Includes three interchangeable BOV springs, allowing you to tailor venting function to your existing modifications. 1.9 (For use with factory software) 2.0 (Pre-installed in the SQV BOV - suitable for stock or "Stage One" software) 2.2 (Suitable for "Stage Two" software) vacuum plugs for the stock diverter valve hoses silicone hose connection to intercooler piping all hardware and hose clamps with instructions

The ECS Kohlefaser Luft-Technik (Carbon Fiber Air Technology) intake for the 135/335/535 is a beautifully crafted dual-cone intake with a glossy carbon fiber enclosure. Developed in-house using ECS's chassis dyno and state of the art laser scanning and 3D CAD technology, the N54 carbon airbox is a direct replacement for the stock system. Laser scanning allows ECS to produce a finished product that is a perfect fit to the engine bay. All tubing is also made from carbon fiber with each piece designed for optimal flow. The carbon fiber sandwiches a special heat-blocking fiberglass core, insulating the air box from engine bay heat. All of this combines to produce more power and torque over a wider RPM range - up to 13ft-lbs and 18hp when combined with a Cobb software tune, FMIC, and exhaust. And it looks amazing every time you open the hood.

135/335/535 ECS Carbon intake features -

• Designed and engineered using CAD technology for optimal flow and fitment
• Dyno proven power and torque gains backed with real-world testing
• Washable/reusable high flow cotton filters (pre-oiled)
• Stainless steel hardware
• Direct replacement for stock air box; integrates seamlessly with stock intake piping
• Beautiful and functional carbon fiber/e-fiberglass construction

This dual-cone intake for the 135/335/535 is similar to the enclosed carbon fiber intake but without the surrounding air box. If you love the look of the open filters and high-tech carbon fiber, this is the kit for you. High-flow cotton air filters connect to CAD engineered carbon fiber intake tubes for an improvement in air flow. The open filter layout releases more intake roar than the stock muffled intake.

135/335/535 ECS open DCI intake features -

• Designed and engineered using CAD technology for optimal flow and fitment
• Washable/reusable high flow cotton filters (pre-oiled)
• Stainless steel hardware
• Direct replacement for stock air box; integrates seamlessly with stock intake piping
• Beautiful and functional carbon fiber/e-fiberglass construction

BMW N54 CTS TURBO BOV PIPE (TIAL FLANGE) is the ultimate upgrade for your BMW's N54 engine, designed specifically for use with the TiAL Q atmospheric blowoff valve. Offered by Turner Motorsport, this CTS Turbo BOV kit includes a 3" mandrel-bent T6 6061 aluminum pipe, finished in a durable black powder coat for long-lasting performance and sleek appearance. The kit ensures a secure fit with 4-ply silicone connectors and stainless steel clamps, providing an OEM-like fit with an aggressive aftermarket sound. Additionally, the pipe features two water-methanol bungs with 1/8" NPT plugs, a CNC machined MAP sensor flange, and a laser-etched CTS Turbo logo. Replace the weak plastic charge piping and failure-prone diverter valve system with this high-quality upgrade, enhancing your ability to hold boost under heavy loads while adding a distinctive sound to your BMW.

• Designed for use with TiAL Q atmospheric blowoff valve
• Durable 3" mandrel-bent T6 6061 aluminum pipe with black powder coat finish
• CNC machined MAP sensor flange for seamless OEM installation
• Includes 4-ply silicone connectors and stainless steel clamps for secure fit
• Features two water-methanol bungs and laser-etched CTS Turbo logo
• Enhances boost holding capacity and provides an aggressive aftermarket sound