BMW Engine Parts for BMW 6 Series F06 (2013+)

Upgrade your stock oil cooler thermostat for improved performance. Swap your factory 110-degree Celsius thermostat for a new 70-degree Celsius version for faster oil flow and extended temperature control. With oil temperatures reaching 230 degrees Fahrenheit by the time your factory thermostat opens, initiating oil flow at lower temperatures proves more effective than attempting to cool down already elevated temperatures.

Utilizing a factory-style thermostat, this upgrade can be used in all weather conditions and allows your engine to warm up properly, unlike thermostat bypass kits.

Kit contents:​

Lower temperature thermostat - 70c (158F) vs Factory 110c (230F)
Low temp thermostat spring

BMW N20 N52 N55 Timing Chain addresses the common issue of timing chain stretch and rattling over time. Although BMW designates the timing chain as a lifetime part, many enthusiasts choose to replace it preemptively. Turner Motorsport offers this direct-fit replacement for those needing to replace a worn or damaged timing chain without opting for a full kit.

• Direct Fit Replacement: Perfect for replacing a stretched or broken timing chain.
• High-Quality Construction: Ensures durability and reliability in maintaining engine timing.
• Ease of Installation: Designed to fit precisely without requiring additional modifications.
• Ideal for Maintenance: A practical choice for enthusiasts who prefer to change the timing chain independently of a full kit.

This eccentric shaft is a vital component of your BMW's N55 Valvetronic system, responsible for precise control of valve lift. In the N55 engine, the Valvetronic system uses intermediate levers between the camshaft and lifters to adjust valve lift dynamically. These levers are actuated by this eccentric shaft, which is rotated by an electronically controlled motor under the direction of the engine computer.

Eccentric shaft failure is a common issue in N55 engines, often caused by inadequate lubrication due to extended oil change intervals. The most frequent failure occurs when the eccentric shaft gear wears down, leading to disengagement from the motor's worm drive. Symptoms include multiple fault codes, such as P1014 (Shaft Parity Error), P1017 (Shaft Sensor Plausibility), P1023 (Valvetronic Adjustment Range), and P10E1 (Valvetronic System No Travel Detected).

If your BMW is experiencing Valvetronic-related fault codes, a failing eccentric shaft could be the source of the problem. Opt for this premium direct replacement from Bremmen Parts to restore your Valvetronic system's functionality and ensure a durable, high-quality repair.

Upgrade your stock oil cooler thermostat for improved performance. Swap out your existing cover with ease, replacing it with a durable billet cover. Upgrade from your 110-degree Celsius thermostat to a new 70-degree Celsius version for faster oil flow and extended temperature control. With oil temperatures reaching 230 degrees Fahrenheit by the time your factory thermostat opens, initiating oil flow at lower temperatures proves more effective than attempting to cool down already elevated temperatures.

Utilizing a factory-style thermostat, this upgrade can be used in all weather conditions and allows your engine to warm up properly unlike thermostat bypass kits.

Kit contents:

Billet thermostat housing cover
Replacement gasket
Hardware
Lower temperature thermostat - 70c (158F) vs Factory 110c (230F)
Low temp thermostat spring

The impulse sending wheel, located on both the intake and exhaust camshaft adjustment units, provides critical timing data to the camshaft position sensor, keeping your VANOS system synchronized. A worn or malfunctioning impulse sender can cause a myriad of performance issues, including hard starts and rough idle.

Whether you are performing a proactive timing system overhaul or addressing a component failure, Bremmen Parts offers a high-quality replacement designed for a precise fit and long-term durability.

Hardware to replace the coarse-thread screws originally used to mount components to the plastic valve cover.

Factory and aftermarket valve covers are made from plastic and use coarse-thread screws designed specifically for plastic. When upgrading to an aluminum valve cover, this hardware can no longer be used, as it will not properly thread into aluminum.

This kit includes all necessary hardware required to mount the factory components onto your upgraded aluminum valve cover.

Included Hardware:

2 × M6 × 1.0 × 40 mm bolts

4 × M6 × 1.0 × 20 mm bolts

2 × M6 × 1.0 × 12 mm bolts

Easily add an oxygen sensor to your custom exhaust setup with this universal O2 sensor bung. Designed for simple weld-on installation, it allows you to place your sensor exactly where you need it—perfect for custom builds, exhaust modifications, or performance tuning projects.

Features:

CNC-cut from T304 Stainless Steel for corrosion resistance
Threaded for M18x1.5mm RH oxygen sensors