BMW Engine Parts for BMW 6 Series F06 (2013+)

Vitesco Fuel Injector With Seal Ring - Index 12 - BMW N54 N63 S63 ...

T#:30629652

Part#: 13538616079

In Stock

12% off MSRP $ 560.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 493.99 USD

Add to Wish List

Qty

12% off MSRP

$ 560.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 493.99 USD

Add to Wish List

If you are experiencing a rough idle, misfire, or check engine light, this could be the problem. Earlier fuel injectors for the N54 have been a common failure item, this is the most up to date injector for the N54 engine. It is highly recommended to replace older injectors also if your car is modified or you plan to modify it. Important information to consider when replacing injectors: It is recommended to replace at least 3 injectors at a time, replacing all injectors in a cylinder bank, instead of mixing and matching. If ALL injectors in a bank are index 11 or greater, injectors may be replaced individually with a new injector. If your stock injectors are index 10 or less, all 3 injectors per bank must be replaced. For V8s, all four in that bank must be replaced. Vehicles with old injector 7585261 will need to inspect their existing injectors to determine if these can be replaced individually. Replacement also requires 13537564751 for each injector.

Show More Show Less

Vitesco Technologies MAP Sensor - BMW N20 N26 S55 S63

T#:39059260

Part#: 13627843531

In Stock

$ 93.99

This product was last offered at the strikethrough price on
06-28-2026

$ 90.99 USD

Add to Wish List

Qty

$ 90.99 USD

Add to Wish List

This is a replacement Manifold Absolute Pressure sensor Located on the charge air cooler. The MAP controls the amount of fuel that goes through the injectors based on the pressure of air at the intake manifold. If your vehicle is giving you a MAP code, replace it immediately to ensure you get the best gas mileage and performance. It is common for this part to fail slowly and cause poor fuel mileage and hampered performance. When it fails, the vehicle will stutter and stall as it falls into a limp mode. One way to check if your MAP is bad is to unplug the connector before starting your car. If it idles well (compared to a previous poor idle), your MAP sensor likely needs to be replaced. If you let this maintenance part go, your fuel economy will suffer as too much fuel is going into the engine and not being burned. A great way to give your vehicle an efficiency boost.

Show More Show Less

Large Aluminum Oil Catch Can

T#:597051

Part#: MMOCCLA

In Stock

$ 127.99 USD

Add to Wish List

Qty

$ 127.99 USD

Add to Wish List

WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.

Show More Show Less

Innovate LC-2 Wideband O2 Controller Kit

T#:28836410

Part#: 38770

In Stock at Vendor

$ 212.99 USD

Add to Wish List

Qty

$ 212.99 USD

Add to Wish List

Features & Benefits:

Two configurable linear 0-5V analog outputs Ability to calibrate O2 sensors for maximum accuracy Includes LC-2 controller and Bosch wideband O2 sensor Comes with a program cable, manual, and a 10 ft. sensor cable Includes a 1-inch mild steel exhaust bung Innovate MTS serial in/out capability Integrated dual-color status LED (green/red) Patented DirectDigital™ wideband sensor control Positive lock connectors for all connections Real-time display data on screen or with the powerful LogWorks software Range:

AFR (Air-Fuel Ratio) range from 7.4:1 to 22.4:1 (0.5 to 1.5 lambda)

Show More Show Less

Vitesco Mass Air Flow Sensor - N55, N52

T#:33512934

Part#: 13627593624

In Stock

$ 219.99 USD

Add to Wish List

Qty

$ 219.99 USD

Add to Wish List

The MAF of your vehicle decides the quantity of fuel that is fed to the injectors according to the volume of air coming through the intake.

Mishimoto Universal Catch Can Kit - Carbon Fiber

T#:372557

Part#: MMOCCCF

In Stock

$ 162.99 USD

Add to Wish List

Qty

$ 162.99 USD

Add to Wish List

Universal kit with a catch can and rubber hose; for retrofitting on a variety of vehicles. Carbon fiber catch can prevents a harmful buildup of oil inside of the turbocharger, intake manifold, intercooler and piping. Separates oil particles from PCV/CCV air Defends intercooler, intake system, and essential components from oil blow-by Made from lightweight carbon fiber Compact design makes for easy engine bay placement Checking fluid levels made easy with built in sight tube Comes complete with mounting bracket, hose, all necessary clamps, fittings, and mounting hardware Mishimoto Lifetime Warranty WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.

Show More Show Less

Vitesco - Fuel Injector Replacement Kit - Index 12 - N63, S63 Engines...

T#:33479599

Part#: 13538616079VKT

In Stock

$ 4,119.99

This product was last offered at the strikethrough price on
08-17-2026

$ 4,103.99 USD

Add to Wish List

Qty

$ 4,103.99 USD

Add to Wish List

If you are experiencing a rough idle, misfire, or check engine light, this could be the problem. Earlier fuel injectors for the have been a common failure item, this is the most up to date injector for the N63 and S63 engine.

Show More Show Less

Walker Oxygen Sensor - Downstream - F22 M235, F3X 335/435, F06/F12 64...

from 7/2013 production date

T#:31324163

Part#: 11787645875

Ships in 1 Business Day

$ 101.99

This product was last offered at the strikethrough price on
04-14-2026

$ 91.99 USD

Add to Wish List

Qty

$ 91.99 USD

Add to Wish List

The oxygen sensor is part of your BMW's emissions control system and feeds data to BMW engine management computer. The oxygen sensor is positioned in the exhaust pipe and can detect rich and lean mixtures. The goal of the oxygen sensor is to help the engine run as efficiently as possible and also to produce as few emissions as possible. When your BMW oxygen sensor fails, the computer can no longer sense the air/fuel ratio, so it ends up guessing -- resulting in poor performance, poor gas mileage, and increased pollution. Make sure your BMW engine performs as it should, and doesn't use more fuel than it needs to, by simply changing your oxygen sensor today.

Show More Show Less

BMW Two Port Universal Catch Can - Black

T#:23020165

Part#: MMBCC-CBTWO

In Stock

$ 160.99 USD

Add to Wish List

Qty

$ 160.99 USD

Add to Wish List

Optimize your vehicle's performance and shield crucial components with the Mishimoto Compact 2-Port Baffled Oil Catch Can. This innovative solution effectively separates oil particles from PCV/CCV air using a 50-micron bronze filter, ensuring defense against oil blow-by for your intercooler, intake system, and vital parts. Constructed with a patented billet 6061 aluminum can sealed with Viton™ O-Rings, this catch can guarantees both durability and effectiveness.

Equipped with a universal mounting bracket, it allows adaptable installation and comes complete with two CNC-machined aluminum 1/2" barbed hose fittings. With an enhanced 3 oz internal capacity, service intervals are prolonged, while its fully serviceable filter and can ensure enduring functionality.

Engineered for safety in pressurized applications, the internal air diverter enhances oil separation by amplifying air turbulence. Available in black, red, or polished finishes, this catch can preserves proper octane levels, reducing potential detonation and promoting extended engine life.

The product package includes the Compact 2-Port Baffled Oil Catch Can, two Aluminum 1/2" Barbed Fittings, and a Universal Mounting Bracket, all backed by the Mishimoto Lifetime Warranty.

WARNING! Prop 65 may apply to this product.

Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to all companies selling products in California.

Prop 65 mandates listing any chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm.

For more information about California Prop 65 warning, visit: www.P65Warnings.ca.gov.

Show More Show Less

Mishimoto Universal 10 Row Oil Cooler

For custom applications only. Not a direct bolt on.

T#:378421

Part#: MMOCU

In Stock

$ 410.99 USD

Add to Wish List

Qty

$ 410.99 USD

Add to Wish List

This universal oil cooler from Mishimoto is far superior to the factory unit with its 11" x 2.76" x 1.97" core. Even under optimum driving conditions increased oil temperatures will cause a drop in pressure and will decrease the ability for your engine to be properly lubricated. With this new oil cooler, you can keep your oil temperatures down for optimum driving conditions. The kit includes 4 feet of stainless braided line, adapter fittings, and oil filter sandwich adapter. Mishimoto Automotive is a leading manufacturer of aftermarket performance cooling products. The company was established back in 2003 with one goal. That goal was to provide customers with quality cooling system upgrades that work on the track and on the road. At Mishimoto, you never have to worry about the quality of the product you are installing. This kit is universal and is not a direct bolt on. *For custom applications only. Not a direct bolt on. WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.

Show More Show Less

Mishimoto Performance Engine Oil Cooler - F10/90 M5, F06/12/13 M6, G1...

T#:6258386

Part#: MMOC-F10-12SL

In Stock at Vendor

$ 887.99 USD

Add to Wish List

Qty

$ 887.99 USD

Add to Wish List

The BMW M5 power and handling statistics are completely mind-blowing for a car tipping the scales at well over two tons. The S63 twin-turbo V8 is underrated from the factory and responds well to tuning and bolt on modifications. Calling it the ultimate super sedan would not do this car justice, it’s just that good. But every amazing automobile must have an Achilles’ heel, right? Some investigation into this model told us that enthusiasts were seeing elevated oil temperatures during track driving conditions. Our team set out to create a replacement, high-performance oil cooler that could handle the rigors of extreme driving conditions and the abuse of daily commuting. The Mishimoto S63 M5/M6 oil cooler features extremely precise CNC-machined billet-aluminum end tanks which are professionally TIG-welded to our robust bar-and-plate core. Our strategically designed 55mm-thick core provides a massive 24% increase in core volume, and a 40% increase in external fin surface area. This added surface area promotes greater heat transfer, which directly impacts internal fluid temperatures. Our performance oil cooler is a complete bolt-on solution that includes everything needed for an easy installation such as hardware and replacement O-rings for the oil lines. Our heat exchanger is finished in a durable silver powder coat, providing both corrosion resistance and improved aesthetics. Whether your M5 sees frequent track time or just the occasional back-road jaunt, upgrading the oil cooler is a great way to extend the life of your S63 and ensure maximum engine output when you need it most. As with all our BMW products, this oil cooler includes our signature Mishimoto Lifetime Warranty. Direct fit for 2012+ BMW M5/M6 models CNC-machined billet aluminum end tanks provide improved durability over stock stamped tanks Robust bar-and-plate core resists damage from road debris and provides optimal cooling efficiency 24% increase in core volume over stock for improved cooling capacity 40% increase in external fin area provides improved heat transfer during extreme driving conditions Precision CNC-machined inlet and outlet prevent leaks Includes new OEM-quality oil line O-rings for easy installation Durable silver powder coated finish prevents corrosion Mishimoto Lifetime Warranty Purchase Includes: (1) Performance Oil Cooler (4) Mounting Bracket Grommets (2) Oil Line Connection M8 X 1.25 Bolts (2) Oil Line O-rings Mishimoto Lifetime Warranty WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov. The Mishimoto S63 M5/M6 oil cooler features extremely precise CNC-machined billet-aluminum end tanks which are professionally TIG-welded to our robust bar-and-plate core. Our strategically designed 55mm-thick core provides a massive 24% increase in core volume, and a 40% increase in external fin surface area. This added surface area promotes greater heat transfer, which directly impacts internal fluid temperatures. Our performance oil cooler is a complete bolt-on solution that includes everything needed for an easy installation such as hardware and replacement O-rings for the oil lines. Our heat exchanger is finished in a durable silver powder coat, providing both corrosion resistance and improved aesthetics. Whether your M5 sees frequent track time or just the occasional back-road jaunt, upgrading the oil cooler is a great way to extend the life of your S63 and ensure maximum engine output when you need it most. As with all our BMW products, this oil cooler includes our signature Mishimoto Lifetime Warranty. Direct fit for 2012+ BMW M5/M6 models CNC-machined billet aluminum end tanks provide improved durability over stock stamped tanks Robust bar-and-plate core resists damage from road debris and provides optimal cooling efficiency 24% increase in core volume over stock for improved cooling capacity 40% increase in external fin area provides improved heat transfer during extreme driving conditions Precision CNC-machined inlet and outlet prevent leaks Includes new OEM-quality oil line O-rings for easy installation Durable silver powder coated finish prevents corrosion Mishimoto Lifetime Warranty Purchase Includes: (1) Performance Oil Cooler (4) Mounting Bracket Grommets (2) Oil Line Connection M8 X 1.25 Bolts (2) Oil Line O-rings Mishimoto Lifetime Warranty

Show More Show Less

MTX-D: Ethanol Content % And Fuel Temperature Gauge

T#:22558994

Part#: INN3904

In Stock at Vendor

14% off MSRP $ 313.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 269.00 USD

Add to Wish List

Qty

14% off MSRP

$ 313.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 269.00 USD

Add to Wish List

Introducing the Innovate Motorsports MTX Digital Series "Dual Function" Gauges – now available! These 2 1/16" (52mm) gauges come with interchangeable faceplates and bezels, locking connectors for simplified installation, and MTS serial connections for seamless integration with other Innovate devices for data logging.

DISPLAY RANGE

Ethanol Content %: 0-100%
Temperature: -40-257 °F (-40-125°C)

KEY FEATURES

Ethanol Content
Error reporting for ethanol content sensor (Digital Display)
Fuel Temperature
Customizable exterior LED display
Programmable exterior LED color options
Selectable unit of measure in °F or °C
Programmable fuel temperature warning (outer LED)
2-Configurable analog outputs
Ethanol Content: 0v = 0%, 5v = 100%
Fuel Temperature: 0v = -40 °F, 5v = 257 °F (-40-125°C)

MTX-D: Ethanol Content Percentage & Fuel Temp Gauge Kit includes Gauge (Black Faceplate, Black Bezel), Silver Bezel & White Faceplate, Harness, Program Cable (Serial), Ethanol Content Sensor, Quick Start Installation Guide.

Please note that this is a universal fitment gauge, and installation may vary depending on the vehicle.

Show More Show Less

Mishimoto 19 Row Universal Oil Cooler

For custom applications only. Not a direct bolt on.

T#:378414

Part#: MMOCUL

In Stock at Vendor

$ 536.99 USD

Add to Wish List

Qty

$ 536.99 USD

Add to Wish List

Even under optimum driving conditions increased oil temperatures will cause a drop in pressure and will decrease the ability for your engine to be properly lubricated. With this new oil cooler, you can keep your oil temperatures down for optimum driving conditions. The kit includes four-feet of stainless braided line, adapter fittings, and oil filter sandwich adapter. Rows: 19 Overall Dimensions: 13" x 5.5" x 2" Core Dimensions: 11.25" x 5.5" x 2" Braided Hoses: 4ft .75 inch & 4ft 9 inch Braided Hose Fittings: -10AN Sandwich Plate Fittings: -10AN WARNING! Prop 65 may apply to this product. Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1968) is a California law that applies to call companies selling products in California. Prop 65 requires any listed chemical present above very low levels that are known to cause cancer, birth defects, or other reproductive harm. For more information about California Prop 65 warning see: www.P65Warnings.ca.gov.

Show More Show Less

Mishimoto Ignition Coils, 6-Pack - BMW M54, N20, N52, N54, N55, N62, ...

T#:51075072

Part#: MMIG-BMW-0206

Ships in 3 Business Days

$ 184.99 USD

Add to Wish List

Qty

$ 184.99 USD

Add to Wish List

The Mishimoto Ignition Coil is built to handle the intense heat cycles found in BMW’s modern turbocharged and naturally aspirated engines.

Denso Alternator

T#:384619

Part#: 12317616119

Back Ordered

$ 442.99 USD

Add to Wish List

Qty

$ 442.99 USD

Add to Wish List

Denso Brand

When power starts to fade in your BMW, chances are your alternator is losing power. The warning light should illuminate, warning you of such a failure. Replace with a new unit today. Do not get stuck on the side of the road.

Show More Show Less

Hitachi Fuel Pump Camshaft Follower - BMW N20 N55 S55 N63 S63 B48/46 ...

T#:589968

Part#: 11327601233

Back Ordered

$ 55.00 USD

Add to Wish List

Qty

$ 55.00 USD

Add to Wish List

A faulty camshaft follower can damage the engine and cause incorrect valve timing.

Liqui-Moly Battery Clamp Grease - 50 grams

10X Entries Into Our F80 M3 Sweepstakes
We Price Match - Give Us A Call or Chat!

T#:1195997

Part#: 20244

In Stock

31% off MSRP $ 7.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 5.50 USD

Add to Wish List

Qty

31% off MSRP

$ 7.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 5.50 USD

Add to Wish List

Excellent corrosion protection for your battery and other connections

Pro-Line Injector And Glow Plug Grease - 20g

10X Entries Into Our F80 M3 Sweepstakes

T#:49787695

Part#: 22243

In Stock

$ 6.99 USD

Add to Wish List

Qty

$ 6.99 USD

Add to Wish List

This high-performance lubricant is formulated to prevent moisture ingress and oxidation, which are the primary causes of "frozen" injectors and glow plugs.

Mishimoto Ignition Coil, 4-Pack - BMW N20, N52, N54, N55, S54, S55 ...

T#:51075078

Part#: MMIG-BMW-0204

Ships in 3 Business Days

$ 123.99 USD

Add to Wish List

Qty

$ 123.99 USD

Add to Wish List

The Mishimoto BMW Ignition Coil is built to handle the intense heat cycles found in BMW’s modern turbocharged and naturally aspirated engines.

Mishimoto Ignition Coil, 8-Pack - BMW N63 & S63 Engines

T#:51075067

Part#: MMIG-BMW-1108

Ships in 3 Business Days

$ 274.99 USD

Add to Wish List

Qty

$ 274.99 USD

Add to Wish List

The Mishimoto Ignition Coil (MMIC-BMW-11B) focuses on durability and electrical precision.

Mishimoto Ignition Coil - Single - BMW M54, N20, N52, N55, N62, N63, ...

T#:51110138

Part#: MMIG-BMW-07

Ships in 3 Business Days

$ 41.99 USD

Add to Wish List

Qty

$ 41.99 USD

Add to Wish List

Mishimoto’s Delphi-style ignition coils offer a premium solution for BMW owners looking to replace worn-out factory units.

Battery Tender Plus Advanced Battery Charging System

T#:49892371

Part#: BTT0210128

In Stock at Vendor

$ 69.99 USD

Add to Wish List

Qty

$ 69.99 USD

Add to Wish List

Mishimoto Ignition Coil, Delphi Style, 6-Pack - BMW E82, E9X, F3X N54...

T#:51075071

Part#: MMIG-BMW-0706

In Stock

$ 204.99 USD

Add to Wish List

Qty

$ 204.99 USD

Add to Wish List

The Mishimoto Ignition Coil focuses on durability and electrical precision.

Mishimoto Stainless Steel T-Bolt Clamp - 3.0"

T#:31589358

Part#: MMCLAMP3

Ships in 3 Business Days

$ 7.99 USD

Add to Wish List

Qty

$ 7.99 USD

Add to Wish List

Hitachi Fuel Supply Module - BMW N20 N55 N26

T#:48850079

Part#: 16117243975

Ships in 6 Business Days

$ 344.99 USD

Add to Wish List

Qty

$ 344.99 USD

Add to Wish List

Delivers fuel from the tank to the engine.

Hitachi Camshaft Position Sensor - BMW E9X F3X F8X N20 N52 N55 S55 ...

T#:48815454

Part#: 13627525014

Ships in 6 Business Days

$ 40.00 USD

Add to Wish List

Qty

$ 40.00 USD

Add to Wish List

The camshaft position sensor communicates the position of the camshaft to the computer. This helps the computer to calculate proper spark and fuel control. If you're struggling with CELs, hard starts or no starts, stalling, and/or a rough idle, you may need to replace the cam position sensor.

Show More Show Less

Mishimoto Ignition Coil - Single - BMW M54, N20, N52, N54, N55, N62, ...

T#:51075090

Part#: MMIG-BMW-02

Ships in 3 Business Days

$ 72.99 USD

Add to Wish List

Qty

$ 72.99 USD

Add to Wish List

The Mishimoto BMW Ignition Coil is built to handle the intense heat cycles found in BMW’s modern turbocharged and naturally aspirated engines.

Denso Starter Motor - BMW N55 S55 3.0L

T#:40004863

Part#: 12417631559

Ships in 2 Business Days

$ 461.99

This product was last offered at the strikethrough price on
05-04-2026

$ 390.99 USD

Add to Wish List

Qty

$ 390.99 USD

Add to Wish List

If your car won't turn over, there is a good chance your starter is shot. Denso's OEM starter is a high quality replacement that will give you peace of mind thanks to its long life-span.

Walker MAP Sensor - BMW N20 N26 S55 S63

T#:39059258

Part#: 13627843531

Ships in 1 Business Day

$ 163.99

This product was last offered at the strikethrough price on
04-10-2026

$ 135.99 USD

Add to Wish List

Qty

$ 135.99 USD

Add to Wish List

This is a replacement Manifold Absolute Pressure sensor Located on the charge air cooler. The MAP controls the amount of fuel that goes through the injectors based on the pressure of air at the intake manifold. If your vehicle is giving you a MAP code, replace it immediately to ensure you get the best gas mileage and performance. It is common for this part to fail slowly and cause poor fuel mileage and hampered performance. When it fails, the vehicle will stutter and stall as it falls into a limp mode. One way to check if your MAP is bad is to unplug the connector before starting your car. If it idles well (compared to a previous poor idle), your MAP sensor likely needs to be replaced. If you let this maintenance part go, your fuel economy will suffer as too much fuel is going into the engine and not being burned. A great way to give your vehicle an efficiency boost.

Show More Show Less