BMW 5 Series F10 (2011-2016)

Replacement N55 Performance Filter, No Hardware

T#:3586313

Part#: REPLACEMENT-N55F

In Stock

$ 70.00 USD

Add to Wish List

Qty

$ 70.00 USD

Add to Wish List

Replacement N55 Performance Filter from Burger Motorsport

Enhance your BMW's performance with the Replacement N55 Performance Filter from Burger Motorsport. Specifically designed for N55 engines, this filter optimizes airflow, leading to increased horsepower and torque. Enjoy improved throttle response and fuel efficiency, all while protecting your engine from harmful contaminants.

Key Features:

Designed for N55 engines
Optimizes airflow for increased power
Improves throttle response and fuel efficiency
Protects engine from contaminants

Show More Show Less

90mm Black M14 BMW 5 Lug Hex Head Stud Kit - APEX

2X Entries For Our G87 M2 Sweepstakes!

T#:26171623

Part#: HW-APX-M14125-90

Ships in 2 Business Days

$ 160.00 USD

Add to Wish List

Qty

$ 160.00 USD

Add to Wish List

Upgrade your BMW race car with a stud conversion kit from [Brand Name] for enhanced strength, safety, and improved pit stop times. Even for non-race cars, stud conversions streamline wheel installation and removal, eliminating the need to align holes before threading lug bolts.

Enhanced strength and safety
Improved pit stop times
Simplified wheel installation and removal
Versatility with extended length wheel studs
Reduced wear on hub threads
Long-term durability and safety
Simplified maintenance and improved efficiency

Show More Show Less

BMS Pedal Tuner - N52, N54, N55

T#:586269

Part#: BMSPBT

In Stock

$ 199.00 USD

Add to Wish List

Qty

$ 199.00 USD

Add to Wish List

The BMS Pedal Tuner is a BMW Performance Chip with a pre-programmed internal chip that intercepts the stock signals from your BMW's electronic control unit (ECU) and changes them to achieve better performance by adjusting the air-fuel ratio and spark timing. Made specifically for the BMW inline six-cylinder motors. The PBX also has an adjustable throttle feature that can be combined with the Performance chip feature by selecting a setting or "map". The BMS Pedal Tuner contains both a performance chip which gives you an extra 8-10 Horsepower at the wheels and an adjustable throttle boost feature that makes the gas pedal send a boosted throttle signal in increments of 30%, 60%, and 100% over the stock BMW signal. Depending on what setting/ "map" you select you can create a perfect blend of throttle response. The BMS Pedal Tuner will make your vehicle more responsive, spirited and fun to drive. It will make your vehicle faster by increasing the horsepower and torque. It works well with other modifications like intakes and exhausts, but can also be used alone. It will remove the "dead space" when you push on the non-responsive stock BMW accelerator. It changes the way the car drives and feels. You can turn it on and off from the comfort of your driver's seat to feel the difference. The BMS Pedal Tuner is a clear choice. Features: Throttle Re-mapping for Better Response / Reaction Removes "dead area" delay in gas pedal 7 Different Maps / Settings for more enjoyable driving Can be set and turned on and off from inside the car Invisible to dealers equipment Made in USA

Show More Show Less

AeroCatch Racing Hood and Body Panel Fasteners (Pair) - Better than h...

T#:340098

Part#: AEROCATCH

In Stock

$ 566.99

This product was last offered at the strikethrough price on
05-13-2026

Starting at $ 82.99 USD

Add to Wish List

Starting at $ 82.99 USD

Add to Wish List

As used by Turner Motorsport on our championship winning BMW race cars, the new aerodynamically efficient and aesthetically styled AeroCatch is setting new standards in hood fixing for the 21st century. Say goodbye to your standard hood pins -- these are better all around.

Show More Show Less

JB4 Bluetooth Wireless Connect Kit - Pinned Power Wire - F-Chassis & ...

T#:598298

Part#: JB4-SPWCK-F

In Stock

$ 159.00 USD

Add to Wish List

Qty

$ 159.00 USD

Add to Wish List

The JB4 Connect Kit (Rev 3.7) allows your Bluetooth 4.0 compatible iOS and Android devices to connect wirelessly to your JB4. View critical engine data in real time, datalog, read codes, change maps, update settings, update firmware, and more, all from the palm of your hand! The REV3 mounts next to the JB4 in the engine bay eliminating the need to run a BMS DATA cable inside the cabin. It's compatible with all JB4 products. Just plug it in to the JB4 where your BMS DATA cable connects, purchase the JB4 Mobile app, and you're off and running. Please note the JB4 Mobile app is available for iPhone®, iOS®, or Android and sold separately via the Apple® or Android® app store on your phone. The wireless adapter is not compatible with the JB4 windows interface. See our other listings for the "BMS DATA cable" for laptop use.

Show More Show Less

330mm MOMO MOD.78 Steering Wheel

T#:301059

Part#: TMS301059

In Stock at Vendor

$ 279.00 USD

Add to Wish List

Qty

$ 279.00 USD

Add to Wish List

This steering wheel combines the best of all worlds for both track/street use and racing requirements. It has an anticorodal aluminum core, durable leather covering, and an ergonomic feel for comfort and control.

Show More Show Less

JB4 Bluetooth Wireless Connect Kit - Separate Power Wire - E-Chassis ...

For use with older E chassis BMW JB4 systems with the square plastic case.

T#:403194

Part#: JB4-BT

In Stock

$ 149.00

This product was last offered at the strikethrough price on
05-13-2026

$ 99.00 USD

Add to Wish List

Qty

$ 99.00 USD

Add to Wish List

The JB4 Connect Kit (Rev 3.7) allows your Bluetooth 4.0 compatible iOS and Android devices to connect wirelessly to your JB4. View critical engine data in real-time, datalog, read codes, change maps, update settings, update firmware, and more, all from the palm of your hand! The REV3 mounts next to the JB4 in the engine bay eliminating the need to run a BMS DATA cable inside the cabin. It's compatible with all JB4 products. Just plug it into the JB4 where your BMS DATA cable connects, attach the power and ground wire to the JB4 harness using the included connectors, purchase the JB4 Mobile app, and you're off and running. Please note the JB4 Mobile app is available for iPhone®, iOS, or Android® and sold separately via the Apple® or Android® app store on your phone. This adapter is not compatible with the JB4 windows interface.

Show More Show Less

APEX ARC-8 18x9.5" ET35 Satin Black Concave Wheel 18.85lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:180712

Part#: ARC81895ET35SMBK

Ships in 8 Business Days

$ 399.00 USD

Add to Wish List

Qty

$ 399.00 USD

Add to Wish List

18x9.5" ET35 Satin Black Concave APEX ARC-8 Wheel 18.85lbs

Wheel Specs
Fitment:	Rear
Size:	18x9.5"
Offset (mm):	35
Weight (lbs):	18.85
Profile:	Concave

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

BMC Performance Air Filter - F06 F10 F12 F80/2 M3 M4 M5 M6

T#:398705

Part#: FB647/20

In Stock at Vendor

$ 207.99 USD

Add to Wish List

Qty

$ 207.99 USD

Add to Wish List

Looking to upgrade your air filter for increased flow and performance? BMC filter allow significantly higher air flow and are perfectly molded in one piece to fit exactly the same as your stock air filter. These filters are constructed from multi-layerd cotton gauze that is pre-oiled and can be cleaned and regenerated using the BMC regeneration kit.

Show More Show Less

APEX ARC-8 18x10" ET25 Hyper Black Concave Wheel 19.95lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:180705

Part#: ARC81810ET25HBK

Ships on Oct 5, 2026

$ 419.00 USD

Add to Wish List

Qty

$ 419.00 USD

Add to Wish List

18x10" ET25 Hyper Black Concave APEX ARC-8 Wheel 19.95lbs

Wheel Specs
Fitment:	Rear
Size:	18x10.0"
Offset (mm):	25
Weight (lbs):	19.95
Profile:	Concave

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

Momo Race Airleather Shift Knob - Black

T#:388419

Part#: RACAIR

In Stock

$ 95.00 USD

Add to Wish List

Qty

$ 95.00 USD

Add to Wish List

Momo Race Airleather shift knob for nearly all BMWs. Installs in minutes for a unique touch to your interior. High quality black perforated Endurance leather, and a silver anodized aluminum base. The Race knob favors over-hand or palm shifting as opposed to a two-finger grip. The shape rests comfortably in your palm and the soft leather is a pleasant touch. This knob is 7.3oz, heavier than most factory BMW or MOMO knobs. Comes with installation kit, ready to install.

Show More Show Less

APEX ARC-8 18x10" ET25 Satin Black Concave Wheel 19.95lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:180704

Part#: ARC81810ET25SMBK

Ships in 2 Business Days

$ 409.00 USD

Add to Wish List

Qty

$ 409.00 USD

Add to Wish List

18x10" ET25 Satin Black Concave APEX ARC-8 Wheel 19.95lbs

Wheel Specs
Fitment:	Rear
Size:	18x10.0"
Offset (mm):	25
Weight (lbs):	19.95
Profile:	Concave

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

Universal BMW Jack Pad Red - Set Of 4

T#:9803960

Part#: BMWJACKPADRED4

Ships in 2 Business Days

$ 79.99 USD

Add to Wish List

Qty

$ 79.99 USD

Add to Wish List

Ensure safe and professional jacking of your BMW, 2020 Supra, or MINI with the Turner Motorsport Jack Pad Adapter. Designed to mimic the factory scissor jack, this adapter allows for secure lifting at any of the 4 factory jack points without causing damage to your vehicle. Made in the USA from solid billet aluminum, it features the Burger Motorsports logo and a honeycomb grip pattern for stability. Simple to use and compatible with most floor jacks, it ensures correct and secure lifting every time. Here are the key benefits:

Safely lifts your BMW, 2020 Supra, or MINI at factory jack points
Prevents damage to rocker panels or vehicle undercarriage
Made from solid billet aluminum for durability
Engraved Burger Motorsports logo for authenticity
Honeycomb grip pattern for stability during use

Show More Show Less

APEX ARC-8 18x9.5" ET35 Anthracite Concave Wheel 18.85lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:180765

Part#: ARC81895ET35AN

Ships in 5 Business Days

$ 399.00 USD

Add to Wish List

Qty

$ 399.00 USD

Add to Wish List

18x9.5" ET35 Anthracite Concave APEX ARC-8 Wheel 18.85lbs

Wheel Specs
Fitment:	Rear
Size:	18x9.5"
Offset (mm):	35
Weight (lbs):	18.85
Profile:	Concave

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX ARC-8 18x9.5" ET22 Race Silver Wheel 19.2lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:342500

Part#: ARC81895ET22RS

Back Ordered

$ 399.00 USD

Add to Wish List

Qty

$ 399.00 USD

Add to Wish List

Silver 18x9.5" ET22 Concave APEX ARC-8 Wheel.

Wheel Specs

Fitment:Rear

Size:18x9.5"

Offset (mm):22

Weight (lbs):19.2

Profile:Concave

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit many BMW models and may fit other models with a specific wheel spacer. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

18x10.5" ET22 Brushed Clear APEX VS-5RS Forged BMW Wheel

2X Entries For Our G87 M2 Sweepstakes!

T#:4607237

Part#: VS5RS18105ET22BC

Ships in 5 Business Days

$ 799.00 USD

Add to Wish List

Qty

$ 799.00 USD

Add to Wish List

OMP Velocita Steering Wheel - 350mm | Black/Yellow Suede

T#:393626

Part#: OD/1958

In Stock

$ 269.00 USD

Add to Wish List

Qty

$ 269.00 USD

Add to Wish List

Sport-inspired 3-spoke OMP Velocita Suede steering wheel in 350mm diameter. Anodized aluminum center with OMP horn button and black Suede rim. The steering wheel rim is oval shaped so your fingers wrap around the rim for improved grip. The spokes have angled contours to give you more leverage and grip. A bright yellow top-center band gives you a strong reference point for when the wheel is angled or back to center. The 350mm size is a bit smaller compared to most BMW wheels (stock is usually around 380mm) and may block gauges or instruments, depending on steering column adjustment. A steering column hub adapter is required.

Show More Show Less

BMW N54 N55 Oil Cooler Valve - Red Burger Motorsport Sport (4/2007+) ...

For vehicles with dual oil cooler lines

T#:588633

Part#: OILVALVE-RED

Ships in 2 Business Days

$ 59.00 USD

Add to Wish List

Qty

$ 59.00 USD

Add to Wish List

This simple engine oil cooler valve from Burger Motorsports increases flow to your fender mounted engine oil/air heat exchanger resulting in lower engine oil temperatures and more consistent performance during heavy throttle. Less restrictive than the spring-loaded units. Installs in minutes and is fully reversible. CNC machined for a precise fit and anodized for protection. Made in the USA. Requires BMW's external sport engine oil cooler which is standard on most 2008+ models, optional on 2007 E9x models. FEATURES AND BENEFITS Easily lower engine oil temperature Stock oil cooler will work more efficient More consistent performance CNC Machined for a perfect fit Made in USA

Show More Show Less

Active Autowerke Rotrex Traction Fluid - One Liter

T#:397307

Part#: 12-032

Ships in 1 Business Day

$ 240.00 USD

Add to Wish List

Qty

$ 240.00 USD

Add to Wish List

Rotrex superchargers utilize a unique traction drive system that sets it apart from other centrifugal-style superchargers. For best performance, Rotrex recommends replacing this fluid every 50,000 miles. This bottle of traction fluid is plenty enough for one supercharger service (typically 750ml).

Show More Show Less

OMP Racing Seat Head cushion for WRC and HRC Seats | Black

T#:393794

Part#: HB/699

Ships in 4 Business Days

$ 69.00 USD

Add to Wish List

Qty

$ 69.00 USD

Add to Wish List

This cushion designed specifically for the WRC and HRC racing seats is a simple addition that adds safety, comfort, and support. It attaches with just two straps to the top of the racing seat and is covered in the same velour fabric as the racing seat itself. A white OMP logo is embroidered in the top half of the cushion to match the design of the seat.

Show More Show Less

OMP Mugello Steering Wheel - Wooden 350mm - Special Order

T#:393667

Part#: OD/2023

Ships in 4 Business Days

$ 149.00 USD

Add to Wish List

Qty

$ 149.00 USD

Add to Wish List

Classic inspired 3-spoke OMP Mugello wood steering wheel in 350mm diameter. Gloss aluminum center with OMP wooden horn button. The steering wheel rim is oval shaped so your fingers wrap around the rim for improved grip. The spokes have 3 holes each that increase in size as they get closer to the center of the steering wheel.

Show More Show Less

Momo Shadow Shift Knob

T#:1787

Part#: SUBKCA

Ships on Sep 4, 2026

$ 105.00 USD

Add to Wish List

Qty

$ 105.00 USD

Add to Wish List

Momo Shadow Carbonlook/Leather shift knob for nearly all BMWs. Installs in minutes for a unique touch to your interior. This knob features a carbon fiber style top and high quality black airleather with black anodized base. The Shadow knob favors over-palm shifting (the palm over the top of the knob). This knob is 4.5oz, slight heavier than stock. Comes with installation kit, ready to install.

Show More Show Less

OMP Steel tall brackets - 36 holes | Black

T#:393735

Part#: HC/923

Ships on Aug 20, 2026

$ 139.00 USD

Add to Wish List

Qty

$ 139.00 USD

Add to Wish List

Multi hole steel seat bracket in compliance with FIA Appendix J art. 253. Updated design, minimum 36 different positions. Length: 495 mm Thickness: 3 mm

OMP Steel low brackets | Black

T#:393730

Part#: HC/733E

Ships in 10 Business Days

$ 95.99 USD

Add to Wish List

Qty

$ 95.99 USD

Add to Wish List

Steel brackets for side mounted seats. Low model. 350 mm length x 3 mm thick.

APEX ARC-8 17x9" ET30 Hyper Black Concave Wheel 16.55lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:180796

Part#: ARC8179ET30HBK

Ships in 2 Business Days

$ 349.00 USD

Add to Wish List

Qty

$ 349.00 USD

Add to Wish List

17x9" ET30 Hyper Black Concave APEX ARC-8 Wheel 16.55lbs

Wheel Specs
Fitment:	Front or Rear
Size:	17x9.0"
Offset (mm):	30
Weight (lbs):	16.55
Profile:	Concave

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX ARC-8 18x9.5" ET22 Satin Black Concave Wheel 19.2lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:180708

Part#: ARC81895ET22SMBK

In Stock

$ 399.00 USD

Add to Wish List

Qty

$ 399.00 USD

Add to Wish List

18x9.5" ET22 Satin Black Concave APEX ARC-8 Wheel 19.2lbs

Wheel Specs
Fitment:	Rear
Size:	18x9.5"
Offset (mm):	22
Weight (lbs):	19.2
Profile:	Concave

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX ARC-8 18x9.5" ET22 Anthracite Concave Wheel 19.2lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:180710

Part#: ARC81895ET22AN

In Stock

$ 399.00 USD

Add to Wish List

Qty

$ 399.00 USD

Add to Wish List

18x9.5" ET22 Anthracite Concave APEX ARC-8 Wheel 19.2lbs

Wheel Specs
Fitment:	Rear
Size:	18x9.5"
Offset (mm):	22
Weight (lbs):	19.2
Profile:	Concave

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX ARC-8 19x9.5" ET22 Silver Wheel 20.95lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:201387

Part#: ARC81995ET22HS

Ships in 5 Business Days

$ 449.00 USD

Add to Wish List

Qty

$ 449.00 USD

Add to Wish List

Silver 19x9.5" ET22 APEX ARC-8 Wheel.

Wheel Specs
Fitment:	Front or Rear
Size:	19x9.5"
Offset (mm):	22
Weight (lbs):	20.95
Profile:	Concave

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit many BMW models and may fit others when used with a specific spacer. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX ARC-8 19x10.5" ET22 Anthracite Wheel 22.95lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:201400

Part#: ARC819105ET22AN

Ships in 5 Business Days

$ 469.00 USD

Add to Wish List

Qty

$ 469.00 USD

Add to Wish List

19x10.5" ET27 APEX ARC-8 Wheel 22.95lbs.

Wheel Specs
Fitment:	Front or Rear
Size:	19x10.5"
Offset (mm):	27
Weight (lbs):	22.95
Profile:	Concave

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX ARC-8 19x10" ET25 Silver Wheel 21.95lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:201396

Part#: ARC81910ET25HS

Ships in 5 Business Days

$ 459.00 USD

Add to Wish List

Qty

$ 459.00 USD

Add to Wish List

19x10" ET25 APEX ARC-8 Wheel 21.95lbs.

Wheel Specs
Fitment:	Front or Rear
Size:	19x10"
Offset (mm):	25
Weight (lbs):	21.95
Profile:	Concave

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX ARC-8 18x9.5" ET35 Hyper Black Concave Wheel 18.85lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:180764

Part#: ARC81895ET35HBK

Ships on Aug 10, 2026

$ 409.00 USD

Add to Wish List

Qty

$ 409.00 USD

Add to Wish List

18x9.5" ET35 Hyper Black Concave APEX ARC-8 Wheel 18.85lbs

Wheel Specs
Fitment:	Rear
Size:	18x9.5"
Offset (mm):	35
Weight (lbs):	18.85
Profile:	Concave

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX EC-7 19x9.5" ET22 Silver Wheel 22.9lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:201363

Part#: EC71995ET22RS

Ships in 5 Business Days

$ 459.00 USD

Add to Wish List

Qty

$ 459.00 USD

Add to Wish List

Silver 19x10" ET25 APEX EC-7 Wheel.

Wheel Specs
Fitment:	Mostly Rear
Size:	19x9.5"
Offset (mm):	22
Weight (lbs):	22.9
Profile:	3, deep dish

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to many BMW models and may fit other models when used with a specific spacer. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX EC-7 19x10" ET25 Silver Wheel 23.5lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:201372

Part#: EC71910ET25RS

Ships in 5 Business Days

$ 469.00 USD

Add to Wish List

Qty

$ 469.00 USD

Add to Wish List

19x10" ET25 APEX EC-7 Wheel 23.5lbs.

Wheel Specs
Fitment:	Front or Rear
Size:	19x10"
Offset (mm):	25
Weight (lbs):	23.5
Profile:	3, deep dish

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX EC-7 19x10.5" ET22 Silver Wheel 23.9lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:201375

Part#: EC719105ET22RS

Ships in 5 Business Days

$ 479.00 USD

Add to Wish List

Qty

$ 479.00 USD

Add to Wish List

19x10.5" ET22 APEX EC-7 Wheel 23.9lbs.

Wheel Specs
Fitment:	Front or Rear
Size:	19x10.5"
Offset (mm):	22
Weight (lbs):	23.9
Profile:	3, deep dish

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX ARC-8 17x9.5" ET35 Concave Wheel - Hyper Black

2X Entries For Our G87 M2 Sweepstakes!

T#:180792

Part#: ARC81795ET35HBK

Ships in 5 Business Days

$ 359.00 USD

Add to Wish List

Qty

$ 359.00 USD

Add to Wish List

Wheel Specifications Style: ARC-8 Size: 17x9.5" Offset (mm): ET35 Color: Hyper Black APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand. All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you. Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page! Price is per wheel.

Show More Show Less

APEX ARC-8 19x10" ET25 Satin Black Wheel 21.95lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:201395

Part#: ARC81910ET25SMBK

Ships in 5 Business Days

$ 459.00 USD

Add to Wish List

Qty

$ 459.00 USD

Add to Wish List

19x10" ET25 APEX ARC-8 Wheel 21.95lbs.

Wheel Specs
Fitment:	Front or Rear
Size:	19x10"
Offset (mm):	25
Weight (lbs):	21.95
Profile:	Concave

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX ARC-8 17x9.5" ET35 Concave Wheel - Anthracite

2X Entries For Our G87 M2 Sweepstakes!

T#:180793

Part#: ARC81795ET35AN

Ships on Aug 7, 2026

$ 349.00 USD

Add to Wish List

Qty

$ 349.00 USD

Add to Wish List

Wheel Specifications Style: ARC-8 Size: 17x9.5" Offset (mm): ET35 Color: Anthracite APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand. All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you. Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page! Price is per wheel.

Show More Show Less

APEX ARC-8 18x10" ET25 Race Silver Wheel 19.95lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:180707

Part#: ARC81810ET25RS

Ships in 8 Business Days

$ 409.00 USD

Add to Wish List

Qty

$ 409.00 USD

Add to Wish List

Silver 18x10" ET25 Silver Concave APEX ARC-8 Wheel.

Wheel Specs
Fitment:	Rear
Size:	18x10.0"
Offset (mm):	25
Weight (lbs):	19.95
Profile:	Concave

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to many BMW models and fit other models when used with a specific spacer. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX ARC-8 19x10.5" ET22 Satin Black Wheel 22.95lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:201398

Part#: TMS201398

Ships on Oct 22, 2026

$ 458.00 USD

Add to Wish List

Qty

$ 458.00 USD

Add to Wish List

19x10.5" ET22 APEX ARC-8 Wheel 22.95lbs.

Wheel Specs
Fitment:	Front or Rear
Size:	19x10.5"
Offset (mm):	22
Weight (lbs):	22.95
Profile:	Concave

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

APEX ARC-8 18x9.5" ET22 Hyper Black Concave Wheel 19.2lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:180709

Part#: ARC81895ET22HBK

Ships in 5 Business Days

$ 409.00 USD

Add to Wish List

Qty

$ 409.00 USD

Add to Wish List

18x9.5" ET22 Hyper Black Concave APEX ARC-8 Wheel 19.2lbs

Wheel Specs
Fitment:	Rear
Size:	18x9.5"
Offset (mm):	22
Weight (lbs):	19.2
Profile:	Concave

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

OMP Corsica Steering Wheel - Dished 330mm, Black Suede

T#:391802

Part#: OD/2012

Ships in 4 Business Days

$ 275.00 USD

Add to Wish List

Qty

$ 275.00 USD

Add to Wish List

Classic 3-spoke OMP steering wheel in 330mm diameter and 95mm dish. Anodized aluminum center with OMP horn button and suede on the rim. The steering wheel rim has a round shape instead of exaggerated oval found on other racing wheels. A top-center band gives you a strong reference point for when the wheel is angled or back to center.

Show More Show Less

OMP Racing GP Racing Steering Wheel -- Black Polyurethane

T#:393744

Part#: OD/1981

Ships in 4 Business Days

$ 159.00 USD

Add to Wish List

Qty

$ 159.00 USD

Add to Wish List

Sporty 3-spoke OMP Racing GP steering wheel in 330mm diameter. Anodized aluminum center with OMP horn button and black leather-like polyurethane rim. The steering wheel rim is oval shaped so your fingers wrap around the rim for improved grip. The spokes have contours for resting your thumbs to give you more leverage and grip. The grip itself is textured at the 9 and 3 positions for extra control of the steering wheel. The 330mm size is on the small size compared to most BMW wheels (stock is usually around 380mm) and may block gauges or instruments, depending on steering column adjustment. A steering column hub adapter is required.

Today OMP Racing is one of the world's leading manufacturers of racing safety equipment and tuning accessories with a catalog of over 3,000 different items. Operating from a technologically advanced 80,000 sqft facility in Italy, OMP products are renowned for its quality, the meticulous attention to details that is constantly challenged by setting higher standards.

Show More Show Less

OMP Steel low brackets - 16 holes | Black

T#:393734

Part#: HC/922

Ships in 5 Business Days

$ 129.00 USD

Add to Wish List

Qty

$ 129.00 USD

Add to Wish List

Multi hole steel seat bracket in compliance with FIA Appendix J art. 253. Updated design, minimum 16 different positions. Length: 400 mm Thickness: 3 mm

OMP Corsica Steering Wheel - 350mm | Black/Yellow Leather

T#:391779

Part#: OD/1956

Ships in 10 Business Days

$ 259.00 USD

Add to Wish List

Qty

$ 259.00 USD

Add to Wish List

Classic inspired 3-spoke OMP Corsica Leather steering wheel in 350mm diameter. Anodized aluminum center with OMP horn button and black Leather rim. The steering wheel rim is oval shaped so your fingers wrap around the rim for improved grip. The spokes have angled contours to give you more leverage and grip. A bright yellow top-center band gives you a strong reference point for when the wheel is angled or back to center. The 350mm size is a bit smaller compared to most BMW wheels (stock is usually around 380mm) and may block gauges or instruments, depending on steering column adjustment. A steering column hub adapter is required.

Show More Show Less

OMP Alluminum tall brackets - 36 holes | Black

T#:393737

Part#: HC/925

Ships in 10 Business Days

$ 199.00 USD

Add to Wish List

Qty

$ 199.00 USD

Add to Wish List

Multi hole aluminium seat bracket in compliance with FIA Appendix J art. 253. Updated design, minimum 36 different positions. Length: 495 mm Thickness: 6 mm

OMP WRC Racing Steering Wheel - Mid-depth 350mm dished | Black suede ...

T#:393639

Part#: OD/1979/N

Ships on Aug 7, 2026

$ 249.00 USD

Add to Wish List

Qty

$ 249.00 USD

Add to Wish List

Classic 3-spoke OMP WRC steering wheel in 350mm diameter. Anodized aluminum center with OMP horn button and black suede rim. The steering wheel rim is oval shaped so your fingers wrap around the rim for improved grip.

Show More Show Less

OMP Seat Sliding bracket

T#:393727

Part#: HC/665

Ships on Aug 13, 2026

$ 99.00 USD

Add to Wish List

Qty

$ 99.00 USD

Add to Wish List

Sliding rail kit to be mounted between the seat mount and the seat.

MOMO Mod.08 Steering Wheel - Black - 350mm Suede

T#:343229

Part#: R1908/35S

Ships on Aug 14, 2026

$ 249.00 USD

Add to Wish List

Qty

$ 249.00 USD

Add to Wish List

This steering wheel combines the best of all worlds for both track/street use and racing requirements. It has an anticorodal aluminum core, durable suede covering, and an ergonomic feel for comfort and control. An ideal size for most cars and drivers, and made by renowned MOMO Italy. This is a most attractive and low cost solution. Hub adapter required.

Show More Show Less

OMP Battery Cut Off Switch / Kill Switch

T#:1614

Part#: EA-462

In Stock

$ 65.00 USD

Add to Wish List

Qty

$ 65.00 USD

Add to Wish List

OMP Battery Cut Off Switch / Kill Switch, for use in racecars as an emergency "kill switch", to depower the electrical system in the event of a crash or other emergency. This cut off switch is FIA approved, has 6 poles and alternator protection, as well as a removable key.

Show More Show Less

APEX EC-7 19x8.5" ET35 Anthracite Wheel 21.9lbs

2X Entries For Our G87 M2 Sweepstakes!

T#:201367

Part#: EC71985ET35AN

Ships in 5 Business Days

$ 439.00 USD

Add to Wish List

Qty

$ 439.00 USD

Add to Wish List

19x8.5" ET35 APEX EC-7 Wheel 21.9lbs.

Wheel Specs
Fitment:	Front or Rear
Size:	19x8.5"
Offset (mm):	35
Weight (lbs):	21.9
Profile:	1, minimal dish

APEX light alloy wheels are the next evolution in flow-forged wheel technology for BMWs. Flow-forming is a semi-forging process that produces a wheel typically stronger than a traditional cast wheel yet is still light weight. The wheels are around 10lbs lighter per wheel than a comparable factory wheel! That's reduced unsprung weight that improves all aspects of performance. The spokes and barrel have been designed to allow generous clearance for big brakes. In other words, these wheels are very impressively engineered and look great too! The design is based on classic motorsport themes that blend with BMW styling and appearance. These wheels look right at home on many BMW models. Multiple color and profile options allow you to set just the right look and stance for your car. As well as being pleasing to the eye these are very strong and functional wheels that are at home on the street as well as the racetrack. Don't let the price fool you - these wheels are high quality, high strength, and in high demand.

All APEX wheels are the BMW standard 5/120 bolt pattern and with a 72.6mm center bore. They are a direct fit to most any 1-series (E82), 3-series (E36, E46, E90, E92, F30), Z3, and Z4-series BMWs. The original BMW center cap, TPMS sensors, and original lug bolts are all carried over from your original wheels (wheel bolts may vary if spacers are used). They come in a wide variety of diameter, width, and offset combinations which gives you multiple fitment and application opportunities. For street use we generally recommend a staggered setup with a rear wheel slightly wider than the front. For track and racing applications a square setup is desired with the same width in the front and rear. Wheel offsets may also vary based on the clearances and stance you wish to achieve. Refer to our image gallery for inspiration. If you'd like more input give us a call or e-mail and we'd be happy to go over the many options with you.

Note: careful consideration of wheel width, offset and tire sizing must be observed when choosing and installing larger wheels. Adding larger wheels may lead to rubbing on suspension components or bodywork. Wheel spacers, new alignment settings, inside fender modifications, or other adjustments may be required. For more information on APEX BMW wheels and BMW wheel fitments in general, check out our APEX Wheels page!

Price is per wheel.

Show More Show Less

Project Cars

SELECT YOUR BMW

Sub-Categories

Replacement N55 Performance Filter from Burger Motorsport

Key Features:

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results