BMW Exhaust Parts, Mufflers & Catalytic Converters for BMW 5 Series F10 (2011-2016)

Our Race Inspired exhaust deletes the rear mufflers in the F10 M5 to allow more of the exhaust sound to be heard. We love our M5 but it's just too quiet so we looked at ways to get more of the stock exhaust to be heard. After evaluating the stock exhaust layout it was easy to see that removing the rear mufflers would accomplish what we wanted. But cutting the mufflers off is just the beginning. We then had to develop a set of pipes and design a set of tips that fit perfectly and also looked right at home on the M5 super sedan. And these M5 muffler delete pipes are the finished product.

Our axle-back exhaust is made from a 304 stainless steel tube in the same diameter as the stock exhaust and with mandrel bends for unimpeded flow. It fits with the stock hangers and is clamped to the stock exhaust pipes once the mufflers are cut off. And the entire installation can be done in about an hour with the exhaust on the car. With factory clamps, you can easily reinstall your stock mufflers or a set of Corsa Performance mufflers at any time. Our tips are also stainless in a perfectly proportioned 89mm (3.5" diameter). They fill out the rear bumper valence perfectly - not too small like stock and not boy-racer large. Tips are available in mirror silver or brushed aluminum..

The final result is that removing the stock mufflers really lets the M5 V8 sing! With the mufflers and flapper valves removed the sound on start-up is scintillating. The sound from the S63TU engine is robust and intoxicating - it just needs to be heard! From outside, the muffler-delete exhaust makes the car seem all the more impressive. From the burble at idle to the roar under full throttle there is little doubt that this is a proper M car. Inside the car during normal driving the sound is not changed much thanks to the Active Sound Design system. It's a little louder but not intrusive or irritating. Around town the car sounds much like stock but just a touch louder. The exhaust pops and burbles more with each downshift. On the highway at 70-80 cruising speeds it's as quiet as a muffled exhaust. We tried to get the exhaust to drone but only experienced it at low speeds in a high gear (i.e. - lugging the engine) which we normally wouldn't do.

Our Race Inspired M5 exhaust is perfect for enhancing and accentuating the stock sound. It lets more of the M5's soundtrack come through without extensive exhaust modifications. If you want to enjoy the M5's sound more, think of this as its volume knob turned up.

This item fits the following BMWs:
2012+ F10 BMW M5

Engineered for vehicles with vacuum-actuated exhaust valves, the ECS Remote Vacuum Exhaust Valve Control Kit puts you in complete command of your exhaust sound. This fully standalone system lets you open or close your valves instantly—no reliance on factory controls, drive modes, or complicated wiring.

At its heart is a self-contained vacuum pump and dedicated control module, operating entirely independent of your vehicle’s electronics. The result is broad compatibility with both OEM and aftermarket exhaust systems, allowing for the freedom to switch between aggressive performance sounds and a refined, quiet tone at the touch of a button.

Kit Includes:

Standalone Vacuum Pump – Delivers consistent vacuum for reliable valve function

Wiring Harness Options – Choose from a reversible cigarette lighter power adapter or a length of wire for custom hardwiring

High-Quality Vacuum Hose – Durable, leak-resistant construction for long-lasting performance

Remote Controllers – Compact fobs for easy operation from inside or outside the vehicle

Features:

Instant open/close control for exhaust valves

Operates completely independent of factory electronics

Universal compatibility with vacuum-actuated valve systems

Ideal for both aftermarket and factory exhaust setups

From stealthy early-morning starts to unleashing your exhaust’s full roar on demand, the ECS Remote Vacuum Exhaust Valve Control Kit gives you total control over your car’s voice—whenever and wherever you want it.

Upgrade your exhaust system with the 2.5" Stainless Steel 3-Bolt Flange - Priced Each. This high-quality flange is designed to provide a durable and reliable connection for your exhaust components. Made from stainless steel, it offers corrosion resistance and longevity, ensuring a lasting performance. Whether you're repairing or customizing your exhaust system, this flange is an essential component for a secure fit.

• Durable stainless steel construction
• Corrosion-resistant for long-lasting performance
• Provides a reliable connection for exhaust components
• Suitable for repair or customization of exhaust systems

Upgrade your exhaust system with the Downpipe To Cat-Back Reducer.

Engineered for optimal performance and durability, this reducer allows for seamless connection between your downpipe and cat-back exhaust system. Its high-quality construction ensures a tight seal, reducing exhaust leaks and enhancing overall exhaust flow. With easy installation and compatibility with various exhaust systems, this reducer is a must-have for any performance enthusiast.

• Allows for seamless connection between downpipe and cat-back exhaust
• High-quality construction for durability
• Tight seal reduces exhaust leaks
• Enhances overall exhaust flow
• Easy installation and compatibility with various exhaust systems

Achieving precise exhaust fitment can be tricky—especially when the exhaust hanger has room to slide. This movement can cause annoying rattles or even lead to contact with the underbody or rear bumper. The ECS Tuning Exhaust Locking Collar offers a simple and effective fix. Designed to clamp securely around the exhaust hanger, this collar keeps everything firmly in place, eliminating unwanted movement.

Crafted from high-strength 6031 billet aluminum and finished in a sleek black anodized coating, it delivers both durability and corrosion resistance. With this collar in place, your exhaust stays exactly where it should—no rattles, no surprises.

Product Design:

Made from precision machined 6061 aluminum Black anodized finish Stainless steel M5 X 0.8mm hardware Installation & Support:

Install the locking collar around your exhaust hanger, position the hanger in place, and snug the locking collar down in place against the hanger! ECS Exhaust Hanger Locking Collars are available for 10mm and 12mm exhaust hangers. Please measure your hangers before ordering. The 12mm locking collar can be found HERE.

Achieving precise exhaust fitment can be tricky—especially when the exhaust hanger has room to slide. This movement can cause annoying rattles or even lead to contact with the underbody or rear bumper. The ECS Tuning Exhaust Locking Collar offers a simple and effective fix. Designed to clamp securely around the exhaust hanger, this collar keeps everything firmly in place, eliminating unwanted movement.

Crafted from high-strength 6031 billet aluminum and finished in a sleek black anodized coating, it delivers both durability and corrosion resistance. With this collar in place, your exhaust stays exactly where it should—no rattles, no surprises.

Product Design:

Made from precision machined 6061 aluminum Black anodized finish Stainless steel M5 X 0.8mm hardware Installation & Support:

Install the locking collar around your exhaust hanger, position the hanger in place, and snug the locking collar down in place against the hanger! ECS Exhaust Hanger Locking Collars are available for 10mm and 12mm exhaust hangers. Please measure your hangers before ordering. The 10mm locking collar can be found HERE.

Embark on your custom exhaust project confidently with the ECS Tuning Universal Exhaust catalog, offering quality and price-friendly options. Crafted from T304 Stainless Steel for corrosion resistance, these items feature premium benefits akin to our In-House Engineered Exhaust Systems. With a 3.0" ID (Slip fit) X 65mm OD (Butt) connections, 1.5mm (.060") wall thickness tubing ensures durability. Length on the 65mm OD side is 2.25" while on the 3.0" ID side is 3.50". Ideal for fabricating your unique exhaust system, these universal parts guarantee top-tier quality and longevity.

Benefits:

• Crafted from T304 Stainless Steel for corrosion resistance
• Features premium benefits akin to In-House Engineered Exhaust Systems
• Durable construction with 1.5mm (.060") wall thickness tubing
• Ideal for fabricating custom exhaust projects
• Ensures top-tier quality and longevity

Turner Motorsport Rolled Angle Exhaust Tip - 3.0 Inlet - 3.0 OD - Stepped Left - Chrome brings a sleek and stylish upgrade to BMW exhaust systems. This high-quality exhaust tip features a striking chrome finish and a rolled angle, stepped design that adds both aesthetics and performance to your vehicle. Its precision design ensures a perfect fit and a bold look. With a 3.0-inch inlet and 3.0-inch outer diameter, this exhaust tip is designed to enhance the visual appeal of your BMW's exhaust system.

• Premium Chrome Finish: Adds a high-gloss, polished look to your vehicle’s exhaust.
• Rolled Angle Design: Provides a stylish and aggressive appearance.
• Stepped Left Design: Ensures a precise fit and a distinctive look.
• 3.0-Inch Inlet & Outer Diameter: Perfectly matches BMW exhaust systems for a seamless upgrade.
• Durable Construction: Built to withstand the elements and maintain its shine.

Universal 2.5" inlet to 3.5" outlet exhaust tip. Priced per exhaust tip.

Over the years, it is not uncommon for exhaust tips to be damaged and corroded, becoming a "sore spot" of your BMW. To remedy this unsightly feature, we now offer our very own exhaust tips! Featuring stainless steel construction and a simple, yet sporty design, this exhaust tip will look perfectly at home on almost any model.

Features & Specifications:

Swivel feature for perfect alignment of the exhaust tips in the rear bumper
2.5" Inner Diameter
3.5" Outer Diameter
Brushed Aluminum Finish
Double Wall Construction
Angle Cut Style
Includes Stainless Steel Clamp

We are proud to introduce our latest exhaust offering, the Black Chrome Rolled Angle Exhaust Tip! This tip comes in a gorgeous chrome finish and features a rolled angle, stepped design. Warning - you may become obsessed with cleaning and taking care of these beautiful tips!

Other Features Include:

3.0 Inlet
3.0 Outer Diameter
Black chrome Finish
Left Stepped Design
Rolled Angle Design

Universal 2.5" inlet to 3.5" outlet exhaust tip. Priced per exhaust tip.

Over the years, it is not uncommon for exhaust tips to be damaged and corroded, becoming a "sore spot" of your BMW. To remedy this unsightly feature, we now offer our very own exhaust tips! Featuring stainless steel construction and a simple, yet sporty design, this exhaust tip will look perfectly at home on almost any model.

Features & Specifications:

Swivel feature for perfect alignment of the exhaust tips in the rear bumper
2.5" Inner Diameter
3.5" Outer Diameter
Brushed Aluminum Finish
Double Wall Construction
Angle Cut Style
Includes Stainless Steel Clamp

Universal 2.5" inlet to 3.5" outlet exhaust tip. Priced per exhaust tip.

Over the years, it is not uncommon for exhaust tips to be damaged and corroded, becoming a "sore spot" of your BMW. To remedy this unsightly feature, we now offer our very own exhaust tips! Featuring stainless steel construction and a simple, yet sporty design, this exhaust tip will look perfectly at home on almost any model.

Features & Specifications:

Swivel feature for perfect alignment of the exhaust tips in the rear bumper
2.5" Inner Diameter
3.5" Outer Diameter
Mirror Chrome Finish
Double Wall Construction
Angle Cut Style
Includes Stainless Steel Clamp