BMW Fuel System Parts for BMW 6 Series F13 (2012+)

New DCSS 39/50 High-Performance Pump – F90000295

• Highest flow in-tank brushed fuel pump offering from TI Automotive / Walbro
• No Internal check valve - ideal for racing applications to build oil pressure prior to start-up
• Featuring award-winning DCSS technology
• E85 compatible
• High-pressure relief setting - supports supercharger and turbo applications
• Capable of supporting 900+HP at 60PSI naturally aspirated applications
• Complete Pump and kit combination – TCD495

Fuel: GAS & E85

Horsepower: 900+ at 60PSI, naturally aspirated applications

Over All Pump Length: 131mm

Main Housing Diameter: 39mm

Lower Housing Diameter: 50mm

Fuel Inlet Diameter: 11mm OD

Fuel Outlet Diameter: 11mm OD

Flow Rate: 535LPH at 40psi

Test Voltage: 13.5 Volts

We are proud to bring out this truly awesome product that makes getting the required Flex Fuel hardware on your BMW and A9X Supra with incredible ease and minimal effort, in your own driveway.

Our kit is entirely plug-and-play with the factory vehicle harness. No cutting or splicing of OEM wiring/connectors. It installs in minutes and can be removed without a trace on the car!

Our team used SolidWorks to design a Flow Optimized Flex Fuel Sensor Adapter (FFSA) to ensure fuel flow is unobstructed and with no added pressure drop at full fuel pump flow from the fuel tank to your motor when our kit is installed. This is important when pushing the factory fuel system with all the power Ethanol can provide over petrol!

Flex fuel sensor housing is designed to neatly install into the factory BMW fuel hat location.

Flex Fuel Sensor Adapter also contains two 1/8 NPT ports that allow installation of an auxiliary Fuel Pressure sensor for vehicles that don’t come with an OEM one from the factory for future use. Depending on fitment, either port can be used.

Install the bootmod3 Flex Fuel Plug and Play Kit and flash your flex fuel enabled bootmod3 OTS MultiMap or Custom Map in minutes and you’re off to the races never worrying about alcohol/petrol blend % in your fuel tank. It does not get better or easier than this!

bootmod3 FlexFuel Plug and Play Kit:

• Minutes to install at home as opposed to hours at a shop with car up on lift fabricating/cutting into factory fuel lines and splicing/cutting/pinning into OEM electrical
• 4+ hours in time/cost savings to get going on Flex Fuel as compared to most other kits that require making custom fuel lines, fittings and custom wiring! 
• Fully reversible/removable and back to stock without a trace in minutes
• Custom 3-piece Aluminum-6061 Flex Fuel sensor adapter with built-in sensor bypass to allow for obstruction free fuel flow made to fit in the vehicle factory fuel hat area below the rear seat
• All connecting points sealed with fuel safe Viton o-rings
• Flex Fuel Sensor Adapter housing provides additional 1/8 NPT ports for optional Fuel Pressure sensor addition to vehicles without a factory one for bootmod3 CustomROM v2 support
• CANBUS Enabled Ethanol Content Analyzer (ECA) that integrates with bootmod3 CustomROM for complete and seamless conversion of your BMW to FlexFuel for bootmod3 Flex Fuel enabled OTS MultiMaps and custom tunes with your bootmod3 tuner of choice
• Power/CANBus 4-wire plug and play harness
  • 100% Fully Plug and Play harness to the BMW Fuel Controller connectors (EKP3) on S55, N55 vehicles
  • 100% Fully Plug and Play harness on the BMW Body Domain Controller (BDC/FEM) connector on Gen1 F-series B48/B58
• Continental Flex Fuel sensor 3-wire harness
• Custom Aluminum-6061 CANBus Enclosure for the bootmod3 ECA board
• Custom, kink-free teflon braided line allowing plug and play installation with the OEM fuel hat and factory 5/16” or 3/8” fuel feed line. No cutting or new lines required.
• -6 AN fitting by Racetronix

OEM FUEL HAT LOCATION KIT IS INTENDED FOR OEM FUEL PUMP AND ASSOCIATED WIRING. ANY VARIATIONS TO FUEL LINES OR FUEL PUMPS MAY NOT BE COMPATIBLE. USE THE ENGINE BAY INSTALLATION KIT WHERE AVAILABLE INSTEAD.

Includes a full set of injectors (13538616079 x8), seals (13537584315 x8), and decoupling elements (13537564751 x8.) Why replace a full set? Fuel injectors are indexed, meaning they have to be replaced with injectors of the same index number and are not recommended to be replaced individually. This kit addresses the issue with 8 new injectors and decoupling rings.

More on injector indexing:

The index number is found on the head of the injector after the BMW part number.

Example: 13 53 8 616 079-11. "11" is the index number.

Injectors with index 10 and lower have a different calibration and construction than injectors with index 11 and higher. Because of this the injectors with index 10 and lower cannot be mixed with index 11 and higher in the same engine.

Ensure reliable fuel system operation with this fuel tank breather hose featuring an integrated sucking jet pump. Designed to regulate tank pressure and facilitate seamless fuel transfer, this critical component helps maintain efficient engine performance and balanced fuel levels, especially in vehicles with saddle-style tanks.

The sucking jet pump ensures proper fuel distribution between tank compartments, while the breather hose prevents pressure build-up by managing vapor flow. Over time, constant exposure to fuel vapors and high temperatures can cause wear, leading to uneven fuel levels or reduced engine efficiency.

Replace your worn or damaged breather hose with this premium-quality solution from Bremmen Parts, designed for durability and a perfect fit to restore your vehicle's fuel system to peak performance.

Introducing the Innovate Motorsports MTX Digital Series "Dual Function" Gauges – now available! These 2 1/16" (52mm) gauges come with interchangeable faceplates and bezels, locking connectors for simplified installation, and MTS serial connections for seamless integration with other Innovate devices for data logging.

DISPLAY RANGE

• Ethanol Content %: 0-100%
• Temperature: -40-257 °F (-40-125°C)

KEY FEATURES

• Ethanol Content
• Error reporting for ethanol content sensor (Digital Display)
• Fuel Temperature
• Customizable exterior LED display
• Programmable exterior LED color options
• Selectable unit of measure in °F or °C
• Programmable fuel temperature warning (outer LED)
• 2-Configurable analog outputs
• Ethanol Content: 0v = 0%, 5v = 100%
• Fuel Temperature: 0v = -40 °F, 5v = 257 °F (-40-125°C)

MTX-D: Ethanol Content Percentage & Fuel Temp Gauge Kit includes Gauge (Black Faceplate, Black Bezel), Silver Bezel & White Faceplate, Harness, Program Cable (Serial), Ethanol Content Sensor, Quick Start Installation Guide.

Please note that this is a universal fitment gauge, and installation may vary depending on the vehicle.