MSI 14x1.25 Bullet Nose Racing Wheel Studs with Dry Lube - F10 F30 F8...

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:340355

Part#: MSI-M14X125

Ships on Jun 26, 2026

Starting at $ 25.98 USD

Add to Wish List

Starting at $ 25.98 USD

Add to Wish List

70MM, 80MM, OR 90MM OVERALL LENGTH
OUR HIGHEST-GRADE PREMIUM WHEEL STUD
DRY LUBE WITH BLACK M-PHOSPHATE COATING
STUD FOR RACE/TRACK USE
CORRECT SHOULDER SIZE FOR A WIDE RANGE OF HUBS/BRAKE ROTORS
USE WITH 14x1.5 NUT
For the very best in a race-grade wheel stud, stop looking! These are the wheel studs that our race teams insist on (after years of trying every stud design on the market). MSI Racing specializes in hardware for motorsport use (NASCAR and IMSA) and other advanced industries. We tried them on our Grand-Am/IMSA racecars and were very impressed by the performance and durability of their designs. Race wins and championships can come down to the seconds of a pitstop. We could run any wheel stud in the world and we use these. After testing them over the course of a few endurance seasons we decided to offer them to all of our customers as well.

These studs are available in three overall lengths - 70.5mm, 80.5mm, and 90.5mm. All sizes are made with aircraft quality alloy steel and have roll formed threads for greater strength than cut threads. We use a dry film lubricant HM-30 coating containing Teflon & Moly over a manganese phosphate finish. Manganese is preferred over the more common zinc because it's better at reducing friction and wear to prevent thread galling. With the dry lube applied over the phosphate this is the best corrosion resistance we have seen in any wheel stud! Salt tests have shown this stud is superior to others in corrosion resistance. The dry lube helps the nut engage and glide over the threads for faster engagement without cross threading or binding. Other features of our MSI studs include a large bullet nose nut-starter and a properly sized shank to work with a wider range of BMW wheel, nut, and brake rotor combinations. We intentionally avoid the extra large shoulders you see on other studs because they can interfere with some brake rotor hats. The extra large shoulder can be too large to allow the rotor to pass through and drilling out the holes is required (not cool!) Our studs have the sufficient shank for the brake rotor without interfering.

We configured these studs to have a 14x1.25 thread to go into the wheel hub. But the exposed stud has 14x1.5 threads. We did this because threading a nut is faster on 1.5 threads than a finer 1.25 thread pitch, which saved us time during pitstops. There are also more wheel nut options in 14x1.5. When you order our 14x1.25 studs make sure you also order the 14x1.5 nuts.

FREE red threadlocker with purchase of a full set of wheel studs (16 or more)MSI Dry Lube Bullet Nose Wheel Stud Features:
Dry film lubricant HM-30 coating containing Teflon & Moly over a manganese phosphate finish
Innovative nut-starter and bullet shape radius that all but eliminates cross-threading
Properly sized shank to work with a wide range of brake rotor, wheel, and nut combinations
Heat-treated aircraft quality alloy steel
Developed from over 20 years of top level NASCAR use
These studs are installed using the traditional 'double-nut' method (one regular nut and one jam nut) with thread locking compound (Red Turbo-Lock or similar).

Sold per stud.
Wheel nuts sold separately.

Show More Show Less

Turner Motorsport 14x1.25 Bullet Nose Wheel Stud - Most New BMWs ...

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:554468

Part#: 025937TMS01

Ships on Jun 19, 2026

Sale - Save 34% $ 459.99

This product was last offered at the strikethrough price on
05-03-2026

Starting at $ 303.60 USD

Add to Wish List

Sale - Save 34%

$ 459.99

This product was last offered at the strikethrough price on
05-03-2026

Starting at $ 303.60 USD

Add to Wish List

60MM, 75MM, 82MM, OR 90MM OVERALL LENGTH
EASY INSTALL WITH ALLEN SOCKET
CERTIFIED ISO/TS 16949 AND ISO 9001 BY TUV
MANUFACTURED IN EUROPE
BLACK M-PHOSPHATE COATING
CORRECT SHOULDER SIZE FOR HUBS/BRAKE ROTORS
STUD FOR MIXED STREET/TRACK USE

Wheel studs are among the safest and most beneficial upgrades you can make on a track car. Not only are wheel studs safer than wheel bolts but they make changing wheels/tires much easier. One of the frustrating things about installing your wheels on the hub is that it's difficult to line up the wheel on the bolt holes. As wheels get larger but also heavier it's even more trouble. Add in a wheel spacer and the task is twice as hard. BMW does produce a wheel alignment pin for this purpose but if you're changing wheels often a stud conversion is the better way to go.

Our original bullet nose studs are available in 60mm, 75mm, 82mm, or 90mm. The 75mm works great for cars that do not use a spacer (or a spacer smaller than 10mm). We recommend the 90mm length for cars that have spacers up to 20mm. The 82mm length is a happy medium between the 75mm and the 90mm. These studs come with a OEM-style black zinc coating for excellent corrosion resistance. These studs are perfect for dual-purpose street/track cars. The studs are stronger and safer than wheel bolts with protection against corrosion which makes them suitable for street use. For a dedicated race or track car, where wheel changes or pit stops are more frequent, check out our racing dry lube studs.

Our studs are also designed and manufactured with the properly sized shank to work with a wider range of BMW wheel, nut, and brake rotor combinations. We intentionally avoid the extra large shoulders you see on other studs because they can interfere with some brake rotor hats. The extra large shoulder can be too large to allow the rotor to pass through and drilling out the holes is required (not cool!) Our studs have the sufficient shank for the brake rotor without interfering.

Not all wheel studs are created equal. We don't take a manufacturer's generic wheel stud from their catalog and call it our own. Turner Wheel Studs are manufactured to meet our own specifications. Beware of cheaper studs on the market! We have seen other studs similar to our own designs that are not a true BMW fitment. There are differences that we have ironed out over our years of selling wheel studs for the BMW market. Our stud prices may be slightly higher than the rock bottom prices on the web but we promise that it's a higher quality.
Turner Bullet Nose Wheel Stud Features:

Black phosphorous corrosion resistant coating
Innovative nut-starter and bullet shape radius that all but eliminates cross-threading
Long shank for good brake rotor alignment
Heat-treated aircraft quality alloy steel
Installation Instructions
Click here for installation instructions and more information.

Sold per stud.

Show More Show Less

Wheel Stud Conversion Kit - Full Set - Multiple BMW Chassis

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:380852

Part#: PRF82CH5KT

In Stock

Sale - Save 3% $ 203.99

This product was last offered at the strikethrough price on
05-02-2026

$ 197.87 USD

Add to Wish List

Qty

Sale - Save 3%

$ 203.99

This product was last offered at the strikethrough price on
05-02-2026

$ 197.87 USD

Add to Wish List

Upgrade Your BMW's Wheel Change Process with a Stud Conversion

Optimize your BMW's wheel change process with a stud conversion kit, delivering faster and simpler wheel swaps. This kit consists of Conical Seat Lug Nuts (20) and 82mm Wheel Studs (20), providing permanent wheel hangers, saving time, and streamlining the process.

Permanent wheel hangers for quick and hassle-free wheel changes
Simplifies the wheel installation process compared to wheel bolts
Accommodates various spacer widths for added versatility
Reduces wear on wheel hubs, enhancing longevity
Facilitates quick and easy tire changes and removal

Note: Thread-locking compound is recommended during installation. Studs should be torqued to 15Nm. These studs may be used with spacers up to 20mm.

Show More Show Less

VTT M14 Titanium Wheel Stud Kits

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:7292018

Part#: TISTUD201425

Back Ordered

Starting at $ 335.99 USD

Add to Wish List

Starting at $ 335.99 USD

Add to Wish List

VTT is proud to offer Titanium wheel stud kits for the vehicle owner looking for the lowest possible unsprung weight while maintaining high strength, and good looks. This kit is 60% lighter than factory steel studs and nuts with a total kit of 20 nuts, and studs being 3.1LBS. VTT kit details are as follows: Grade 5 Titanium studs, rated at more than 135,000PSI Tensile Strength Grade 5 Titanium nuts with 60-degree cone seat to fit most all aftermarket wheel applications M5 Hex for easy installation Three Colors Available – Raw, Black, Burnt M14x1.25x75mm on the small end to M14x1.5 on the long end. This will convert M14x1.25 cars into M14x1.5 pattern Installation notes: Apply locktite to the studs (short end) and torque to 20 ft/lb. Lug nuts should be torqued to factory specifications. For safety retorque all hardware (studs and nuts) after 25-50 miles.

Show More Show Less

BMS Elite Titanium Cone Seat Lug Nuts - M14x1.25 - 20

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:21209837

Part#: BMS-ETLN20

Ships in 7 Business Days

$ 199.00 USD

Add to Wish List

Qty

$ 199.00 USD

Add to Wish List

BMS Elite titanium lug nuts are up to 50% lighter than equivalent OEM steel lugs, have a high tensile strength, and do not succumb to heat degradation, rust, or corrosion. Material: Hot forged grade 5 titanium Ti-6AL-4V Color: Black Wight: 22g each Thread: M14x1.25 Seat: 60º Cone/Conical Hex Head: 19mm Type: Open Set: 20 Lug Nuts

Show More Show Less

Titanium Conical Seat Wheel Bolt - 14x1.25x35mm - Set Of 20

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:6908168

Part#: 025384ECS05-0221

Ships on Jul 27, 2026

Sale - Save 10% $ 332.99

This product was last offered at the strikethrough price on
05-03-2026

$ 299.69 USD

Add to Wish List

Qty

Sale - Save 10%

$ 332.99

This product was last offered at the strikethrough price on
05-03-2026

$ 299.69 USD

Add to Wish List

Enhance Your BMW's Performance with Titanium Conical Seat Wheel Bolt - 14x1.25x35mm - Set Of 20

Lightweight titanium construction reduces unsprung weight
Corrosion-resistant for long-lasting durability
Conical seat design ensures optimal wheel fitment
Set of 20 bolts for complete wheel installation

Elevate your BMW's performance with the Titanium Conical Seat Wheel Bolt - 14x1.25x35mm - Set Of 20. Crafted from lightweight titanium, these bolts reduce unsprung weight, enhancing agility and responsiveness. Their corrosion-resistant properties ensure long-lasting durability, even in harsh driving conditions. The conical seat design provides optimal wheel fitment, promoting safety and stability. With a set of 20 bolts included, this kit is perfect for complete wheel installation.

Show More Show Less

Turbo-Lock Blue Medium Threadlocker (10ml Bottle)

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:215383

Part#: 11-010BC

In Stock

$ 8.99 USD

Add to Wish List

Qty

$ 8.99 USD

Add to Wish List

Threadlocker is essential when doing any work to your car, especially prepping it for the track. Loose bolts should never happen! If you are a do-it-youselfer, or do much wrench turning, then you know about threadlocker (generically known as "locktite" or by the brand name Loctite). You also know a little goes a long way. This small bottle of Palm Labs Turbo-Lock blue threadlock is perfect for that small job -- or a few small jobs! This tube has 10 mL (0.34 fluid ounces) of moderate temp, medium-strength threadlocker. This bottle comes with two ways to apply: with a squeeze or with the included brush. There are just too many different uses for this, and no mechanic or DIYer, should be without some in his or her toolbox.

Red or Blue threadlocker? Red is the highest strength so use it when the fastener will not be removed regularly or ever again. The Red will need a great amount of force to break free and maybe even heat. Blue is the medium strength and will break free with hand tools. Use it for fasteners that need extra locking protection but will be removed / disassmebled on a semi-regular basis.

Palm Labs Turbo-Lock Blue Features:

color: blue

Anaerobic Thread-locking Compound

permanent

medium strength

moderate temperature resistant

oil resistant

primerless

acceptable up to 20mm (3/4") bolts
Equivalent or superior to Loctite 242.

MSDS Data Sheet
Technical Data Sheet

Show More Show Less

M14x1.5, 19mm Lug Nut - Black

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:641222

Part#: 40.0001BLK

In Stock

$ 5.99 USD

Add to Wish List

Qty

$ 5.99 USD

Add to Wish List

Replacement M14x1.5 19mm Lug nut

Turbo-Lock Red High-Strength Threadlocker (10ml Bottle)

affirm Starting At 0% APR - Subject To Eligibility. See Lending Terms

T#:215382

Part#: 12-010BC

In Stock

$ 7.99 USD

Add to Wish List

Qty

$ 7.99 USD

Add to Wish List

Threadlocker is essential when doing any work to your car, especially prepping it for the track. Loose bolts should never happen! If you are a do-it-youselfer, or do much wrench turning, then you know about threadlocker (generically known as "locktite" or by the brand name Loctite). You also know a little goes a long way. This small bottle of Palm Labs Turbo-Lock red threadlock is perfect for that small job -- or a few small jobs! This tube has 10 mL (0.34 fluid ounces) of high-temp, high-strength threadlocker. This bottle comes with two ways to apply: with a squeeze or with the included brush. There are just too many different uses for this, and no mechanic or DIYer, should be without some in his or her toolbox.

Red or Blue threadlocker? Red is the highest strength so use it when the fastener will not be removed regularly or ever again. The Red will need a great amount of force to break free and maybe even heat. Blue is the medium strength and will break free with hand tools. Use it for fasteners that need extra locking protection but will be removed / disassmebled on a semi-regular basis.

Palm Labs Turbo-Lock Series 13-OR Features:

color: red/orange

Anaerobic Thread-locking Compound

permanent

high strength

high temperature resistant

oil resistant

primerless

acceptable up to 20mm (3/4") bolts
Equivalent or superior to Loctite 262.

MSDS Data Sheet
Technical Data Sheet

Show More Show Less

Project Cars

SELECT YOUR BMW

Stud Conversion Kits for BMW X Series F15 (2014+)

MSI 14x1.25 Bullet Nose Racing Wheel Studs with Dry Lube - F10 F30 F8...

Turner Motorsport 14x1.25 Bullet Nose Wheel Stud - Most New BMWs ...

Wheel Stud Conversion Kit - Full Set - Multiple BMW Chassis

Upgrade Your BMW's Wheel Change Process with a Stud Conversion

VTT M14 Titanium Wheel Stud Kits

BMS Elite Titanium Cone Seat Lug Nuts - M14x1.25 - 20

Titanium Conical Seat Wheel Bolt - 14x1.25x35mm - Set Of 20

Enhance Your BMW's Performance with Titanium Conical Seat Wheel Bolt - 14x1.25x35mm - Set Of 20

Turbo-Lock Blue Medium Threadlocker (10ml Bottle)

M14x1.5, 19mm Lug Nut - Black

Turbo-Lock Red High-Strength Threadlocker (10ml Bottle)

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results