BMW Exhaust Parts, Mufflers & Catalytic Converters for BMW X Series F16 (2015+)

The oxygen sensor is vital to the performance and drivability of your car. The engine computer relies on data from the sensor to make adjustments in engine efficiency and performance. When your BMW oxygen sensor fails, the computer can no longer sense the air/fuel ratio, so it ends up guessing -- resulting in poor performance, poor gas mileage, and increased pollution. Make sure your BMW engine performs as it should, and doesn't use more fuel than it needs to, by simply changing your oxygen sensor today. There is no lifespan on O2 sensors but there are several fault codes that indicate a failed sensor (O2 monitoring, cat efficiency, O2 heating circuit, O2 readiness, and others). The O2 sensor is heated and has a self-calibration feature so once you get the codes or feel performance has suffered, a new sensor is a good starting point to get you back to peak performance. Bosch's Oxygen sensors are high quality and will give you the the longest and best performance for the price.

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMW Chassis:
E82,E90,E92,E93,F30,F34

Fits BMW Engines including:
N55 - up to 08/2013

The oxygen sensor is part of your BMW's emissions control system and feeds data to BMW engine management computer. The oxygen sensor is positioned in the exhaust pipe and can detect rich and lean mixtures. The goal of the oxygen sensor is to help the engine run as efficiently as possible and also to produce as few emissions as possible. When your BMW oxygen sensor fails, the computer can no longer sense the air/fuel ratio, so it ends up guessing -- resulting in poor performance, poor gas mileage, and increased pollution. Make sure your BMW engine performs as it should, and doesn't use more fuel than it needs to, by simply changing your oxygen sensor today.

This item fits the following BMW Chassis:
E82,E90,E92,E93,F30,F34

Fits BMW Engines including:
N55 - up to 08/2013

BMW enthusiasts looking to fabricate a custom exhaust project will find quality and price-friendly options in the ECS Tuning Universal Exhaust catalog. These select items feature the same premium benefits as our In-House Engineered Exhaust Systems, ensuring confidence in their quality and longevity.

Part Design:

• Made from T304 Stainless Steel for corrosion resistance with an attractive brushed finish
• 3.0" outside diameter (OD)
• 1.5mm (.060") wall thickness tubing for durability
• U-Bend Centerline Radius - 5.0" @ 180° angle
• Leg Length "A" - 7.0"
• Leg Length "B" - 14.0"
• Leg Length "C" - 27.0"

Product Development:

• Developed top-tier exhaust components through our In-House Engineered Exhaust Systems
• Direct-fit components for specific European applications now available for custom exhaust projects

Installation and Support:

• Universal parts with no direct fitment to any particular vehicle
• Custom welding and fabrication required
• Special prep/clean procedures must be followed for proper welding due to brushed finish

Elevate your BMW with ECS Tuning Universal Exhaust components, designed for quality and durability in custom exhaust projects.

Achieving precise exhaust fitment can be tricky—especially when the exhaust hanger has room to slide. This movement can cause annoying rattles or even lead to contact with the underbody or rear bumper. The ECS Tuning Exhaust Locking Collar offers a simple and effective fix. Designed to clamp securely around the exhaust hanger, this collar keeps everything firmly in place, eliminating unwanted movement.

Crafted from high-strength 6031 billet aluminum and finished in a sleek black anodized coating, it delivers both durability and corrosion resistance. With this collar in place, your exhaust stays exactly where it should—no rattles, no surprises.

Product Design:

Made from precision machined 6061 aluminum Black anodized finish Stainless steel M5 X 0.8mm hardware Installation & Support:

Install the locking collar around your exhaust hanger, position the hanger in place, and snug the locking collar down in place against the hanger! ECS Exhaust Hanger Locking Collars are available for 10mm and 12mm exhaust hangers. Please measure your hangers before ordering. The 12mm locking collar can be found HERE.

Secures the exhaust manifold to the head. Used on all BMW N-series motors that are turbo-charged.

Genuine BMW Flange Nut
This item fits the following BMW Chassis:
E82 1M Coupe,E71 X6,E82,E89 Z4,E90,E92,E93,F01,F02,F06,F10,F12,F13,F15,F16,F22,F25 X3,F26 X4 X4,F30,F31,F32,F33,F34,F36

Fits BMW Engines including:
N20,N26,N54,N54T,N55
 

Achieving precise exhaust fitment can be tricky—especially when the exhaust hanger has room to slide. This movement can cause annoying rattles or even lead to contact with the underbody or rear bumper. The ECS Tuning Exhaust Locking Collar offers a simple and effective fix. Designed to clamp securely around the exhaust hanger, this collar keeps everything firmly in place, eliminating unwanted movement.

Crafted from high-strength 6031 billet aluminum and finished in a sleek black anodized coating, it delivers both durability and corrosion resistance. With this collar in place, your exhaust stays exactly where it should—no rattles, no surprises.

Product Design:

Made from precision machined 6061 aluminum Black anodized finish Stainless steel M5 X 0.8mm hardware Installation & Support:

Install the locking collar around your exhaust hanger, position the hanger in place, and snug the locking collar down in place against the hanger! ECS Exhaust Hanger Locking Collars are available for 10mm and 12mm exhaust hangers. Please measure your hangers before ordering. The 10mm locking collar can be found HERE.

Embark on your custom exhaust project confidently with the ECS Tuning Universal Exhaust catalog, offering quality and price-friendly options. Crafted from T304 Stainless Steel for corrosion resistance, these items feature premium benefits akin to our In-House Engineered Exhaust Systems. With a 3.0" ID (Slip fit) X 65mm OD (Butt) connections, 1.5mm (.060") wall thickness tubing ensures durability. Length on the 65mm OD side is 2.25" while on the 3.0" ID side is 3.50". Ideal for fabricating your unique exhaust system, these universal parts guarantee top-tier quality and longevity.

Benefits:

• Crafted from T304 Stainless Steel for corrosion resistance
• Features premium benefits akin to In-House Engineered Exhaust Systems
• Durable construction with 1.5mm (.060") wall thickness tubing
• Ideal for fabricating custom exhaust projects
• Ensures top-tier quality and longevity