BMW Engine Parts for BMW F87 M2 N55 3.0L

VTT S55 Crank Bolt Capture - F8X S55 F3x N55

2X Entries Into Our F80 M3 Sweepstakes

T#:557934

Part#: VTT-S55-CBC

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

The S55 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load.

Motiv ReFlex+ for BMW

T#:17970629

Part#: RFXF02UI6

In Stock

$ 859.00 USD

Add to Wish List

Qty

$ 859.00 USD

Add to Wish List

The MOTIV ReFlex+ is an Advanced I/O Integration module allowing a level of precise control of auxiliary components. In addition, the ReFlex can incorporate external data into the factory DME/ECU in parallel through optional CANbus integration. Utilizing the CANbus option, multiple digital and analog signals can be used by the DME/ECU for safety, data logging, or adaptive tuning features. It is unique in its ability to function as a separate standalone, as well as a parallel module in conjunction with the DME/ECU. The ReFlex provides the most accurate and precise supplementary sequential fuel injection with the ability to control other advanced features all in one place. It brings a new level of control, function, and versatility to tuning any modern-day vehicle. Preset crank and cam trigger for most modern-day BMW engines, as well as fully configurable triggers to be synched on any vehicle application. Configurable to operate on 4, 5, 6, and 8-cylinder engines. 3 Point MAP sensor calibration table makes it configurable for almost any MAP or TMAP sensor. Sequential Port Injection with the ability to sense individual injector failures on 4 to 8-cylinder engines. Built-in Ethanol Content Analyzer. The Re|Flex firmware and XDFs include ethanol compensation tables to scale properly for varying ethanol % based on real-time input from the sensor. 2x Additional Outputs. These outputs have 12x12 resolution tables for control in TunerPro R/T. These can be configured to run as on/off, digital, frequency (25hz), or PID. Boost Control WGDC Methanol Solenoid Control PWM (for use with valves such as the Aquamist FAV and the ProMeth Pulse Valve) Nitrous Solenoid Control PWM Auxiliary fuel pump relay trigger 2x Inputs Ethanol Content Sensor Fuel Pressure Sensor (0-10bar) Oil Pressure (0-10bar) Coolant Pressure (0-10bar) EGBP/EMAP (0-10bar) CANbus (not required) enabled communication for the transmission and receiving of digital signals for fully DME/ECU integrated control of external modifications. The CANbus communications also allow for data and errors to be transmitted to and from the vehicle's engine control computer in order to add safeguards and implement engine trips and fail safes. Logging via OBDII is still fully functional and is not affected at all by the communication with the Re|Flex. Some of the developments underway include: Error reporting to and from factory ECU for unparalleled safety Output WGDC by converting an EWG signal to a more conventional DC output for controlling standard 3port and 4port boost solenoids for use with external WG’s The ability to datalog non-factory parameters such as ethanol content, additional pressure sensor, PI IDC, and more! These features make the Re|Flex the most powerful and safest supplementary and auxiliary controller on the market. However, this is only the beginning. As flash platforms find the need for more accessories to control, the Re|Flex was designed to be updated easily by the end user in order to add functionality as it is developed.

Show More Show Less

BMW Oil Cap Crankcase Breather - All BMW w/2 prong oil fill cap ...

2X Entries Into Our F80 M3 Sweepstakes

T#:558084

Part#: VTT-CRANK-BREATH

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

VTT is happy to introduce the first and only available plug and play crankcase breather kits for ALL BMW applications that use the two-prong oil tab style oil fill caps. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay.

Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups for the ultimate in crankcase pressure relieve

Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase.

This breather will fit:
ALL BMW's with the two-prong style oil fill cap including but not limited to N54, N55, S55, S54

NOTE: NOT ALL THE MODELS LISTED HAVE THE SAME HOOD CLEARANCE, WE CANNOT SAY WHICH MODELS WILL HAVE CLEARANCE ISSUES, AND WHICH WILL NOT AS WE HAVE NOT TEST IT ON ALL MODELS. IF YOU ARE ORDERING THE BREATHER FOR ANYTHING OTHER THAN AN N54 TEST CLOSE YOUR HOOD CAREFULLY TO ENSURE CLEARANCE IF IT DOES NOT FIT LET US KNOW, AND WE WILL GET YOU A REFUND ONCE THE BREATHER IS RETURNED.

MODEL LIST OF REPORTED CLEARANCE ISSUES: N55 E/F 3 SERIES

Show More Show Less

BMW B46 B48 B58 Motiv ReFlex 0-10 Bar Pressure Sensor

T#:28537533

Part#: 101-0216

Ships in 5 Business Days

$ 105.00 USD

Add to Wish List

Qty

$ 105.00 USD

Add to Wish List

BMW B46 B48 B58 Motiv ReFlex 0-10 Bar Pressure Sensor is designed for accurate measurement of fluid and air pressure in high-performance applications. Ideal for monitoring a variety of pressures including fuel, boost, coolant, and oil, this sensor provides crucial data for optimizing vehicle performance.

Featuring a 2-Pin DTM connector, this sensor offers a direct plug-and-play connection to the ReFlex+ harness, ensuring a seamless integration with flash platforms via CANbus. Each ReFlex+ unit can support up to two of these sensors, allowing for comprehensive monitoring.

Versatile Measurement: Capable of measuring fuel pressure, boost, coolant, oil, and other fluids.
Easy Integration: 2-Pin DTM connector provides a direct plug-and-play connection.
Comprehensive Monitoring: Supports integration of up to two sensors per ReFlex+ unit.
High-Performance Design: Designed to handle high pressures and deliver accurate readings.

For optimal installation, consider using the 3/8 Female to 3/8 Male SAE Quick Disconnect Adapter with a 1/8" NPT port on an ethanol sensor or the 5/16 Female to 5/16 Male SAE Quick Disconnect Adapter with a 1/8" NPT port on a factory fuel line. Please note that the ethanol sensor is not included.

Show More Show Less

BMW B46 B48 Motiv ReFlex Plug-n-Play Ethanol Sensor Harness

For Vehicles With Motiv ReFlex Unit Currently Installed Only

T#:22723690

Part#: 101-0212

In Stock

$ 49.00 USD

Add to Wish List

Qty

$ 49.00 USD

Add to Wish List

BMW B46 B48 Motiv ReFlex Plug-n-Play Ethanol Sensor Harness simplifies the integration of an ethanol content sensor into your BMW's Re|Flex system. This harness is designed to enhance your vehicle's performance by scaling the sequential port injection based on real-time ethanol content, eliminating the need for manual adjustments. Key benefits include:

Effortless Installation: Plug-n-play design makes it easy to connect an ethanol content sensor without extensive modifications.
Real-Time Adjustments: Allows for automatic scaling of port injection based on real-time ethanol content, optimizing engine performance.
Seamless Integration: For CANbus integrated vehicles, it facilitates integration with the factory DME/ECU (pending feature release by tuning platforms).
No Manual Flashes Required: Removes the need for ground disconnection or map switching on your port injection controller.

Please note that the ethanol sensor is not included with this harness.

Show More Show Less

Vargas N54/55 Billet Crank Seal Guard - BMW N54 N55 3.0L

2X Entries Into Our F80 M3 Sweepstakes

T#:638889

Part#: VTT-CRANKGUARD

In Stock

Starting at $ 89.99 USD

Add to Wish List

Starting at $ 89.99 USD

Add to Wish List

It is a well-known issue on the BMW N54/55 platforms that your serpentine belt can fail for various reasons. When this happens, there is a high chance of the belt getting sucked behind the front damper pulley and then being pushed past the crank seal into your oil pan. From there it can get sucked into the oil pick up causing total engine failure. Even if you do not lose the engine, it is a COSTLY repair to remove the sub-frame and drop the oil pan to remove the belt. The best way to combat this is to watch for oil leaks and keep up on your maintenance. BUT, even with those preventative measures, pre-mature belt failure can occur. This crank seal guard installs over your front crank seal and will keep the belt from being sucked in if a belt failure does occur. This is a cheap way to ensure you do not end up having to replace your motor from oil starvation due to an ingested belt. Vargas' seal is different from those already on market in two major ways. Firstly, it is not offensively priced. Secondly, it is 100% billet with no welds on the tabs to break, no cheap bent thin steel pieces. 100% Billet 6061-T6 aluminum, anodized black for long-term corrosion resistance. Crank Seal Guard includes: One VTT Billet N54/55 Crank Seal Guard Two extended 12.9 Grade bolts, and two stainless washers We highly recommend you install WITH a crank bolt capture at the same time, as you have to remove the damper anyway. Then you will get the benefit of helping eliminate the dreaded spun crank hub and the crank seal issue

Show More Show Less

Vargas "Spline Lock" Crank Hub Solution - Includes Crank Bolt Capture...

2X Entries Into Our F80 M3 Sweepstakes

T#:558795

Part#: VTT-CRANKHUB-1

In Stock

$ 889.99 USD

Add to Wish List

Qty

$ 889.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

DeatschWerks 255 LPH In-Tank Fuel Pump W/ Universal Set Up Kit ...

Not for sale or use in the state of California.

T#:34919033

Part#: 9-201-1000

In Stock

$ 109.00 USD

Add to Wish List

Qty

$ 109.00 USD

Add to Wish List

BMW B58 3.0L ReFlex+ Main Injector Harness - Inline-6

T#:29201081

Part#: 900.1008

In Stock

$ 200.00 USD

Add to Wish List

Qty

$ 200.00 USD

Add to Wish List

BMW B58 3.0L ReFlex+ Main Injector Harness - Inline-6 offers a seamless integration solution for your turbocharged BMW inline-6 engine. Designed to work with the Motive ReFlex Control Unit, this plug-n-play harness ensures a hassle-free installation process for your 6 EV6/USCAR injectors.

Direct Plug-N-Play Installation: Connects directly to the ReFlex+ Control Unit and your EV6/USCAR injectors.
Versatile Connector Options: Includes DTM 3-Pin and 2-Pin connectors for integration with ethanol content sensors and external sensors.
Multiple Sensor Connectors: Features connections for a 0-10 Bar Pressure Sensor and a 0-5v sensor.
Auxiliary Output Wires: Provides 3x unterminated wires for additional low-side triggers from the ReFlex+ Control Unit.
Easy Connection: DTM 8-Pin connector allows for straightforward setup with ReFlex+ Install Harnesses.

Turner Motorsport's harness ensures efficient and reliable performance, streamlining the process of integrating your ReFlex+ Control Unit with your BMW B58 engine.

Show More Show Less

DeatschWerks 340 LPH In-Tank Fuel Pump with a Universal Set Up Kit ...

This is Universal and Not a direct replacement for the Genuine Pump!

T#:6091453

Part#: 9-301-1000

In Stock

$ 169.00 USD

Add to Wish List

Qty

$ 169.00 USD

Add to Wish List

DeatschWerks was founded in 2004 in Oklahoma and has dedicated themselves to providing high quality EFI applications to a wide variety of manufacturers. DW has developed a wide variety of innovative fuel system components including fuel pumps, modular surge tanks, conversion fuel rails, dual-stage fuel filters, and ethanol compatible fuel pressure regulators. The DW300 is DeatschWerks' flagship standard fitment in-tank pump. The DW300 flows 340lph at 40psi and is a popular choice for e85 applications or wherever the highest flowing standard fitment in-tank pump is needed. Quiet operation and pulse width modulation compatibility are delivered via the turbine impeller and computer balanced armature. E85 compatibility is built in via the carbon commutators and a fully encapsulated armature. All DW fuel pumps are backed by a 3-yr no fault warranty. Features: Weight 12.6 oz (360grams) 7.7mm ID/11mm OD inlet fitting Outlet 5/16" Hose Clamp Single Scroll Composite Turbine All instructions are also provided on DeatschWerks' website.

Show More Show Less

Motiv ReFlex+ Control Unit

T#:29101684

Part#: 900.1001

In Stock

$ 729.00 USD

Add to Wish List

Qty

$ 729.00 USD

Add to Wish List

The motive ReFlex+ Control Unit is an advanced I/O integration module that allows precise control of aftermarket components and sends data to the factory DME (ECU) via CANbus communication, expanding performance tuning capabilities. This control unit allows for precise control of fuel pumps, methanol injection kits, nitrous kits, boost controllers, relay triggers, port injection systems, flex fuel systems, and more. Supporting sequential port injection for up to eight injectors and real-time monitoring of injectors, this unit is a great choice for precise control of fuel delivery to your engine.

Show More Show Less

Magnetic Sump/Oil Pan Plug

T#:22723756

Part#: MMR03-0504

In Stock

$ 37.99 USD

Add to Wish List

Qty

$ 37.99 USD

Add to Wish List

Motiv ReFlex Lite: Advanced Sequential Injector Controller - Inline-6...

T#:29234298

Part#: 910.1011

In Stock

$ 479.00 USD

Add to Wish List

Qty

$ 479.00 USD

Add to Wish List

The ReFlex LITE is a simple yet elegant fueling solution for direct injected vehicles that need to add more fuel by installing a port injection system to keep up with their modifications to the vehicle. Using the same precise form of sequential fuel injection as the ReFlex+, the ReFlex LITE brings a more affordable fuel controller without the additional features of the ReFlex+. Sequential port fuel injection for inline-6 engines Firmware and maps are available for multiple vehicles FREE on our website High resolution calibration tables 24x24 cell RPM vs MAP 0-48psi MAP pressure range 250RPM increments up to 8500RPM High resolution datalogging Fault detection status available to monitor in TunerPRO RT Compact in size Universal fitment Simple installation Please Note: The ReFlex LITE does NOT have the ability to analyze and transmit ethanol content to an ECU.

Show More Show Less

Spline Lock Crank Hub Solution W/ Complete Package - N55 S55 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:18733532

Part#: VTT-CRANKHUB-6

In Stock

$ 986.99

This product was last offered at the strikethrough price on
06-28-2026

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

3/8" Quick Disconnect Adapter With 1/8" NPT Port

T#:29500156

Part#: 200.1105

In Stock

$ 24.00 USD

Add to Wish List

Qty

$ 24.00 USD

Add to Wish List

Quick disconnect adapters (QDA) are commonly used to adapt different components into vehicle fuel systems without requiring permanent modification. These adaptersÂ are machined from high-grade aluminum and anodized for corrosion resistance. QDAs incorporate VitonÂ© o-rings which are compatible with most types of fuel, solvents and oils. QDAs maintain a reliable leak-proof seal under normal fuel injection system operating pressures. This particular QDA is sized perfectly to adapt right between the fuel line you were going to connect to your ethanol sensor. 3/8" (9.5mm) female quick disconnect 3/8" (9.5mm) male quick disconnect 1/8" Female pipe thread port * Viton© o-rings Crecent-lock system E-85 compatible Black anodized aluminum

Show More Show Less

Vargas Ignition Coil Kit (Red) - N5x

2X Entries Into Our F80 M3 Sweepstakes

T#:5309610

Part#: VTT-COIL-N5X-RED

Ships in 10 Business Days

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.

Show More Show Less

Vargas Ignition Coil Kit (Blue) - N5x

2X Entries Into Our F80 M3 Sweepstakes

T#:5309605

Part#: VTT-COIL-N5X-BLU

In Stock

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.

Show More Show Less

TurboSmart OPR V2 Oil Pressure Regulator

T#:28504207

Part#: TS-0811-0012

In Stock

10% off MSRP $ 189.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 170.99 USD

Add to Wish List

Qty

10% off MSRP

$ 189.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 170.99 USD

Add to Wish List

Introducing Turbosmart’s OPR V2 Turbocharger Oil Pressure Regulator, a cutting-edge solution launched in 2022 that ensures steady oil pressure for your turbocharger. This innovative regulator features a return-less design with an integrated 44 Micron Stainless Steel Mesh Oil Filter, providing robust performance and protection.

The OPR V2 is the first of its kind, utilizing Turbosmart’s proprietary flow control method to maintain optimal oil pressure regardless of engine oil variables like pressure or temperature. It guarantees a smooth oil flow to your turbocharger, safeguarding critical components such as Exhaust Drive, Back & Charge Pressures from excessive oil pressure that could lead to oil consumption and smoke.

Gone are the days of guesswork with restrictors and complex plumbing for oil pressure regulation. The OPR V2 simplifies the process with its return-less, inline installation and the convenience of a built-in 44 Micron Oil Filter. This filter, made of serviceable and replaceable Stainless Steel Mesh, adds an extra layer of defense against engine oil debris that could harm your turbocharger.

Key Features:

Innovative Patent Pending Design Durable Aluminium (6262 T6) Anodised Body & Valve Regulated Oil Pressure Compatible with Most turbochargers Integrated Stainless Steel (304) Mesh Oil Filter -4AN Inlet and Outlet for easy installation 1/8 NPT Sensor/Gauge Port for monitoring Directional Inlet Feed Logic for optimized performance Laminar Flow Output for consistent oil delivery Compatible with all Engine Oils Designed and Manufactured in Australia

Show More Show Less

MMR Low Temp Thermostat - N54/N55

For 2008 and up models

T#:4565826

Part#: MMR17-0101

Back Ordered

$ 70.99 USD

Add to Wish List

Qty

$ 70.99 USD

Add to Wish List

MMR's Low Temp Oil Thermostat is one of the easiest ways to increase your oil cooling capability. Rated to maintain the oil temps at about 194F (90c) to 230F (110c). Machined from aircraft grade T-6061 aluminum and anodized in MMR's trademark finish for durability. Installation is easy as it fits right into the OEM oil thermostat housing on the N54 and N55. Highly recommended for cars used on the track or with a higher power and torque output than stock.

Show More Show Less

VTT Ignition Coil Conversion Kit - S55/N55 To B58 - Multiple Color Op...

2X Entries Into Our F80 M3 Sweepstakes

T#:22196341

Part#: VTTS55CLCNV

Ships in 9 Business Days

Starting at $ 335.99 USD

Add to Wish List

Starting at $ 335.99 USD

Add to Wish List

VTT is proud to offer its very own Game Changer S55/N55 to B58 Coil conversion kit for the BMW S55/N55 platforms. The 55 series of engines has notoriously had ignition problems with the factory coils, while aftermarket upgrades do exist, they can be bulky. The solution is the BMW B58 ignition coils which are extremely robust and can support well over 1000WHP with no issues. This means a plug-and-play affordable solution that fits like stock, and looks AMAZING doing so! We designed our own 6061-T6 Billet bracket in a plethora of colors including matching shades for every S55/N55 Valve Cover. This means you can mix and match the color of the bracket with coil color, with VC color to truly tailor your engine bay to look exactly how you want it to! The kit comes with the following: 3 – Billet Aluminum Coil Brackets in the color of choice 6 – Plug and play VTT wiring harnesses 6 – Custom VTT stalks to convert the B58 coils to the S55/N55 head (We ensure proper spring length inside the boot for optimal spring-to-plug contact) *NOTE: Flash setting changes may be required when installing the conversion kit to ensure the proper function of the B58 coils with S55/N55 DME. This can be found in almost all flashing software settings such as MHD, Bm3, etc.* **NOTE: THESE BRACKETS FIT STOCK S55 VC, VTT S55 BILLET VC, and MOST N55 made after 2011. If you have an older N55 made before 01/2011. These may not fit. Purchase carefully as items that have been installed or attempted to cannot be returned.**

Show More Show Less

ReFlex+ Install Harness - Flying Lead

T#:29201083

Part#: 900.1016

Ships in 5 Business Days

$ 95.00 USD

Add to Wish List

Qty

$ 95.00 USD

Add to Wish List

A flying lead harness is a wiring harness that is unterminated at one end and has an excess length of wire so that installation can be customized by the end user. That makes this section of the ReFlex+ Install Harness truly universal. On one end, this harness has an 8-pin connector to plug into any one of our ReFlex+ Main Injector Harnesses. The other end of each wire is unterminated and will be connected to the appropriate sensor, ground, or power supply based on installation instructions. Each harness has a wire for: Switched +12v Input w/ inline fuse +5v Input Ground Can HI Can Lo Cam Sensor Signal Crank Sensor Signal Map Sensor Signal

Show More Show Less

MMX Oil Filler Cap - Black

For Most BMW Models 2007 Onwards or Mini Models

T#:4552062

Part#: MMR03-0102-BL

In Stock

$ 127.99 USD

Add to Wish List

Qty

$ 127.99 USD

Add to Wish List

MMX's Performance billet oil filler cap machined from billet T-6061 aluminum has been designed to instantly give your engine bay an subtle aesthetic upgrade. This cap comes in a Black finish. *Note: After exposure to excessive heat over prolonged periods, overall finish fading can occur. Reusing of original seal is required.

Show More Show Less

AutoTecknic Dry Carbon Competition Oil Cap Cover - Type 1 - For Vario...

T#:39971047

Part#: BM-0007

In Stock

$ 64.99 USD

Add to Wish List

Qty

$ 64.99 USD

Add to Wish List

a precision-engineered, lightweight dry carbon fiber upgrade designed to enhance the engine bay of compatible BMW models with an aggressive motorsport look and easy OEM-style installation.

DeatschWerks Performance Fuel Injector Set - 50lb/hr(550cc)

For Custom Applications - Will require additional tuning or modifications. NOT DIRECT DROP IN!

T#:6151339

Part#: 16U-00-0050-6

In Stock

$ 403.99

This product was last offered at the strikethrough price on
06-03-2026

$ 399.00 USD

Add to Wish List

Qty

$ 399.00 USD

Add to Wish List

DeatschWerks was founded in 2004 in Oklahoma and has dedicated themselves to providing high quality EFI applications to a wide variety of manufacturers. DW has developed a wide variety of innovative fuel system components including fuel pumps, modular surge tanks, conversion fuel rails, dual-stage fuel filters, and ethanol compatible fuel pressure regulators. All DeatschWerks high flow fuel injectors are built using only quality OEM cores. In addition, each set is balanced to within a 2% flow variation. This means better fitment, easier tuning, and increased reliability. Full set of 6 50lb/hr 550cc injectors. All relevant tuning data available on DeatschWerks website.

Show More Show Less

MMX Performance - 4-Pin One-Piece Crank Hub Upgrade Kit - With MMR Ca...

T#:45039725

Part#: MMR20-1004FK

Ships in 3 Business Days

$ 1,227.99 USD

Add to Wish List

Qty

$ 1,227.99 USD

Add to Wish List

The centerpiece of this MMX kit is the UK-made CNC-machined one-piece crank hub, created from billet EN36 steel that's heat-treated with a 0.75mm case hardening, making it incredibly strong and durable. Included are four aerospace precision-machined dowels that mechanically lock the hub to the end of the crank itself, plus a brand new OE bolt. Installation of these dowels is certainly not a DIY job. But, to make the job easier for the professionals, ensuring that the required crank modifications are made safely and accurately, the MMX kit also includes a full installation jig that includes a bolt-on drilling guide, a location bolt for this guide, plus an HSS rolled high-speed drill bit. Together, the single-piece design combined with the four-pin location ensures that there is simply no way that the friction plates can ever slip. With the new OE crank bolt tightened appropriately, this delivers a transformational improvement in reliability and peace of mind versus the OE version. Also included is the MMR Crank Bolt Capture Plate. This adds one additional layer of defense, preventing the crank bolt from being able to back out and loosen over time, ensuring everything is tightly held together as intended.

Show More Show Less

Spline N55 S55 Lock Crank Hub Solution W/ Hardware Package

2X Entries Into Our F80 M3 Sweepstakes

T#:18733531

Part#: VTT-CRANKHUB-5

Ships in 10 Business Days

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

MMX Oil Catch Can Kit - N55

T#:4565831

Part#: MMR17-0501FK

Ships in 6 Business Days

$ 476.99 USD

Add to Wish List

Qty

$ 476.99 USD

Add to Wish List

Higher mileage engines and especially ones with direct-injection are prone to carbon build-up on the backs of the inlet valves. However, when deposits are removed by the catch can's filter and separation process, the intake air receives less oil and more oxygen, resulting in a cleaner, more reliable, and better performing engine. MMR's Performance catch can kit For N55 powered M235i's and M2's was designed to help owners ensure their engines are running at optimum performance This is done by removing unwanted oil from the PCV system before it can get back into the intake. The T-6061 billet filter housing, anodized in the trademark MMR finish, comes with a billet bracket for easy installation, including all hoses and fittings necessary for installation. The catch can kit has been designed to offer added performance, allow easy installation and enhanced aesthetics too. Checking the level for any oil removed from the intake system is easy thanks to the integral dipstick. A cap-head bolt mounted in the lower section of the catch can allows for easy draining, or if you prefer, the lower section itself can be easily unscrewed and removed. Features: Effectively prevents oil build-up in the intake system and intercooler walls Maintains optimum engine performance Easy installation with all supplied hardware included Race fittings and PTFE-lined hoses throughout Easy oil level checking and draining

Show More Show Less

Hella Hella Horn - Low Tone

T#:590880

Part#: 2768082

In Stock

$ 36.99 USD

Add to Wish List

Qty

$ 36.99 USD

Add to Wish List

Disc Type Low-Tone, 12 V, 335 Hz with Bracket

Hella Hella Horn - High Tone

T#:592707

Part#: 2768551

In Stock

$ 30.99 USD

Add to Wish List

Qty

$ 30.99 USD

Add to Wish List

Disc Type High-Tone, 12 V, 400 Hz with Bracket

AutoTecknic Dry Carbon Charge Cooler Tank Cap Cover - Gloss Finish ...

T#:39971051

Part#: BM-0032

In Stock

$ 64.99 USD

Add to Wish List

Qty

$ 64.99 USD

Add to Wish List

A premium dry carbon fiber engine bay upgrade that enhances the performance styling of compatible BMW models with a sleek, UV-resistant finish and easy OEM-style installation.

MMX Oil Filter Housing - Black

T#:4552065

Part#: MMR03-0101-BL

Ships in 1 Business Day

$ 142.99 USD

Add to Wish List

Qty

$ 142.99 USD

Add to Wish List

If you are looking for peace of mind over the prone to cracking OEM plastic housing cap, this oil filter housing cap by MMX may be exactly what you are looking for. Composed of billet aluminum, this cap is light, durable, and dresses up your engine bay! Comes finished with a polished anodized dark anthracite coating. Installation is simple as it can be replaced while completing an oil change. *Note: After exposure to excessive heat over prolonged periods, overall finish fading can occur.

Show More Show Less

MMR Crank Hub Kit - N55/S55

T#:4565824

Part#: MMR20-1003FK

Ships in 2 Business Days

$ 849.99 USD

Add to Wish List

Qty

$ 849.99 USD

Add to Wish List

Anyone with a modified N55/S55 knows the risks involved with the OEM Crank Hub. When the engine simply can't handle the stresses its put under or the design is such that it simply does not support extreme conditions, issues can arise. Under certain conditions, the N55/S55 crank hub likes to spin, without warning and even when the engine is in perfect health. MMR has produced a EN36 machined billet one-piece crank hub heat treated with a 0.75mm case hardening which makes it extremely durable. Due to the one-piece design, it ensures that the friction plates cannot slip. This offers a huge jump in reliability when paired with a new properly torques crank bolt. Installation is requires no drilling or modification to the OEM crankshaft ensuring a perfect fit! Included in this kit is MMR's T-6061 machined billet aluminum capture plate anodized in their trademark finish. The MMR Performance capture plate secures the head of the OE crank bolt and prevents it from turning or being able to loosen. *Installation recommended by a professional shop or technician.

Show More Show Less

Vargas Burnt Titanium Magnetic Oil Drain Plug - M12 X 1.5

2X Entries Into Our F80 M3 Sweepstakes

T#:51813315

Part#: VTT-TI-DRAIN

Ships in 5 Business Days

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

The VTT Burnt Titanium Magnetic Oil Drain Plug is a critical upgrade for any performance enthusiast looking to maximize engine longevity.

VTT N5X/S55/N2X Billet BMW Oil Filter Housing Cap - Clear - BMW N52 N...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122266

Part#: VTTFILTERCAPCLR

Ships in 1 Business Day

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

VTT is proud to offer a billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap and the need for a special tool for removal, while adding some pop and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. Vargas Turbo designed these caps to complement their N5X Billet Oil caps and N5X Billet Power Steering caps so that all 3 will have the same design. The caps are offered in 4 colors – Red, Black, Blue, and Clear anodized

Show More Show Less

VTT N5X/S55/N2X Billet BMW Oil Filter Housing Cap - Blue - BMW N52 N5...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122267

Part#: VTTFILTERCAPBLUE

Ships in 4 Business Days

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

VTT is proud to offer a billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap and the need for a special tool for removal, while adding some pop and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. Vargas Turbo designed these caps to complement their N5X Billet Oil caps and N5X Billet Power Steering caps so that all 3 will have the same design. The caps are offered in 4 colors – Red, Black, Blue, and Clear anodized

Show More Show Less

S55 / N55 One-Piece Crank Hub Upgrade Kit - 4-Pin

T#:19891361

Part#: MMR20-1004

Ships in 1 Business Day

$ 1,064.99 USD

Add to Wish List

Qty

$ 1,064.99 USD

Add to Wish List

Both the N55 and S55 engines are plagued by the same issue when chasing high horsepower numbers... the dreaded crankhub failure. Fortunately MMR Performance has released an upgraded version of their already stout single-piece crankhub, but this time offering a 4-pin dowelled location that locks onto the front of the crankshaft. This configuration eliminates the multi-piece crankhub with friction discs in favor of a more robust single piece crankhub. Recommended for high-powered cars over 700 Horsepower

Show More Show Less

Accusump Marine 2 Qt Kit

T#:8246787

Part#: 24-126

Ships on Sep 23, 2026

17% off MSRP $ 1,006.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 839.00 USD

Add to Wish List

Qty

17% off MSRP

$ 1,006.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 839.00 USD

Add to Wish List

OMP Battery Cut Off Switch / Kill Switch

T#:1614

Part#: EA-462

In Stock

$ 65.00 USD

Add to Wish List

Qty

$ 65.00 USD

Add to Wish List

OMP Battery Cut Off Switch / Kill Switch, for use in racecars as an emergency "kill switch", to depower the electrical system in the event of a crash or other emergency. This cut off switch is FIA approved, has 6 poles and alternator protection, as well as a removable key.

Show More Show Less

VTT N5X/S55/N2X Triple Billet Cap Kit - Red - BMW N20/52/54/55 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122280

Part#: TRIPLECAPRED1

Ships on Sep 18, 2026

$ 209.99 USD

Add to Wish List

Qty

$ 209.99 USD

Add to Wish List

Save 10% by buying all 3 VTT Billet Caps together! VTT is proud to offer their billet replacement for the factory plastic Power Steering Cap, Oil Filter Housing Cap, and Oil Fill Cap. These caps do away with the weak plastic construction while adding some pop and color to your engine bay. These caps retain ALL of the factory provisions to ensure proper fitment and operation. Vargas Turbo designed these caps to complement each other, so all 3 will have the same design and color shades. These caps come in 4 colors – Red, Black, Blue, and Clear anodized.

Show More Show Less

AutoTecknic - Carbon Competition Fuel Cap Cover - Various BMW and MIN...

T#:39971046

Part#: BM-0006-BCG

In Stock

$ 65.00 USD

Add to Wish List

Qty

$ 65.00 USD

Add to Wish List

AutoTecknic - Carbon Competition Fuel Cap Cover - Various BMW and MINI Models is a premium exterior upgrade crafted from genuine carbon fiber, designed to enhance the aggressive styling and performance aesthetic of compatible BMW and MINI vehicles with an easy, OEM-fit installation.

Show More Show Less

Blue WG38 Gen V Ultra-Gate 38 - 14PSI

T#:22591972

Part#: TS-0551-1011

In Stock at Vendor

10% off MSRP $ 430.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 387.99 USD

Add to Wish List

Qty

10% off MSRP

$ 430.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 387.99 USD

Add to Wish List

The Gen V WG38 Ultra-Gate 38 external wastegate is your cost-effective, high-performance solution. This 38mm external wastegate is meticulously designed for hassle-free bolt-on applications that make use of the 2-bolt flange.

Show More Show Less

BMW Fuel Line Upgrade - Short Line Kit

T#:29267521

Part#: 900.1025

In Stock

$ 150.00 USD

Add to Wish List

Qty

$ 150.00 USD

Add to Wish List

Factory fuel lines are often not designed or safe for use with ethanol based fuels. Our PTFE fuel lines are the perfect solution for installing into your vehicle without having to permanently modify your vehicle's fuel lines. Simply uninstall the factory line and install our pre-measured lines that come setup with the correct fittings for a plug-n-play install in your vehicle. Please Note: This does NOT include an ethanol Content Sensor.

Show More Show Less

VTT N5X/S55/N2X Triple Billet Cap Kit - Black - BMW N20/52/54/55 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122279

Part#: TRIPLECAPBLK1

Ships in 10 Business Days

$ 220.99 USD

Add to Wish List

Qty

$ 220.99 USD

Add to Wish List

Save 10% by buying all 3 VTT Billet Caps together! VTT is proud to offer their billet replacement for the factory plastic Power Steering Cap, Oil Filter Housing Cap, and Oil Fill Cap. These caps do away with the weak plastic construction while adding some pop and color to your engine bay. These caps retain ALL of the factory provisions to ensure proper fitment and operation. Vargas Turbo designed these caps to complement each other, so all 3 will have the same design and color shades. These caps come in 4 colors – Red, Black, Blue, and Clear anodized.

Show More Show Less

Hella Air Horn Kit

T#:592708

Part#: 3001651

Ships in 1 Business Day

$ 143.99

This product was last offered at the strikethrough price on
05-07-2026

$ 124.99 USD

Add to Wish List

Qty

$ 124.99 USD

Add to Wish List

Get noticed with this air horn kit from Hella!

VTT N5X/S55/N2X Triple Billet Cap Kit - Clear - BMW N20/52/54/55 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122281

Part#: TRIPLECAPCLR1

Ships in 10 Business Days

$ 249.99 USD

Add to Wish List

Qty

$ 249.99 USD

Add to Wish List

Save 10% by buying all 3 VTT Billet Caps together! VTT is proud to offer their billet replacement for the factory plastic Power Steering Cap, Oil Filter Housing Cap, and Oil Fill Cap. These caps do away with the weak plastic construction while adding some pop and color to your engine bay. These caps retain ALL of the factory provisions to ensure proper fitment and operation. Vargas Turbo designed these caps to complement each other, so all 3 will have the same design and color shades. These caps come in 4 colors – Red, Black, Blue, and Clear anodized.

Show More Show Less

Vargas Ignition Coil Kit (Black) - N5x

2X Entries Into Our F80 M3 Sweepstakes

T#:5309609

Part#: VTT-COIL-N5X-BLK

Ships in 10 Business Days

$ 167.99 USD

Add to Wish List

Qty

$ 167.99 USD

Add to Wish List

Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for N5x Engines. VTT N5X coils are tested against Delphi 10571 coils which are an upgrade over stock N5X factory coils. The VTT performance matches or exceeds a Delphi 10571 Coil. The coils are offered in a choice of black, red, and blue.

Show More Show Less

DeatschWerks DW400 In-Tank Fuel Pump W/ Universal Set Up Kit ...

T#:5389791

Part#: 9-401-1001

In Stock at Vendor

$ 239.00 USD

Add to Wish List

Qty

$ 239.00 USD

Add to Wish List

The DW400 surpasses the 400LPH benchmark by delivering an industry leading in-tank flow of 415LPH at 40psi. Even more importantly, the DW400 delivers 31% more flow than its nearest competitor, the Walbro 450 "e85", at pressures between 70 and 100 psi. The DW400 has a 46mm diameter width and is compatible with pump gas, e85, and race fuels. The pump is also compatible with pulse width modulated pump drivers. The pump ships with a universal fitment kit which includes fuel hose, clamps, electrical harness, and filter. As with all DW products, the pump is warrantied for 3-yrs to the original purchaser.

Show More Show Less

VTT N5X/S55/N2X Billet BMW Oil Filter Housing Cap - Black - BMW N52 N...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122264

Part#: VTTFILTERCAPBLK

Ships in 10 Business Days

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

VTT is proud to offer a billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap and the need for a special tool for removal, while adding some pop and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. Vargas Turbo designed these caps to complement their N5X Billet Oil caps and N5X Billet Power Steering caps so that all 3 will have the same design. The caps are offered in 4 colors – Red, Black, Blue, and Clear anodized

Show More Show Less

Spline Lock Crank Hub Solution

2X Entries Into Our F80 M3 Sweepstakes

T#:8061334

Part#: VTT-N55-CRANKHUB

Ships in 10 Business Days

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

VTT N5X/S55/N2X Billet BMW Oil Filter Housing Cap - Red - BMW N52 N54...

2X Entries Into Our F80 M3 Sweepstakes

T#:5122265

Part#: VTTFILTERCAPRED

In Stock

$ 89.99 USD

Add to Wish List

Qty

$ 89.99 USD

Add to Wish List

VTT is proud to offer a billet replacement for the factory plastic Oil filter housing cap. This cap does away with the weak plastic cap and the need for a special tool for removal, while adding some pop and color to your engine bay. These oil filter housing caps retain ALL of the factory provisions for the filter basket, including the lower pins which are important for the proper function of pressure bypass, etc. They also have cooling fins to help with oil temps. Vargas Turbo designed these caps to complement their N5X Billet Oil caps and N5X Billet Power Steering caps so that all 3 will have the same design. The caps are offered in 4 colors – Red, Black, Blue, and Clear anodized

Show More Show Less

Project Cars

SELECT YOUR BMW

BMW Engine Parts for BMW F87 M2 N55 3.0L

Sub-Categories

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results