BMW Engine Parts for BMW X5 M S63 4.4L

Elevate your custom installation with the ECS -10AN O-Ring Boss fitting, a crucial component that connects your ECS Tuning Catch Can to a 3/4" ID hose. This fitting simplifies your plumbing setup, ensuring a seamless solution.

Featuring a pre-installed Viton O-ring, this fitting is engineered for excellence, providing a leak-proof seal that resists the effects of oil and fuel exposure, guaranteeing long-term durability.

The 3/4" nipple is thoughtfully designed with barbs to secure hose position effectively, minimizing the risk of hose disconnection. Keep in mind that clamps and hoses are available for separate purchase. These fittings are sold individually, with most installations requiring a pair of them.

If you're experiencing hard starting, flaky charging, or other electrical issues, your engine ground strap may be the culprit. On E70/E71 BMWs, the engine ground strap is a thin, non-insulated cable that spans from the left engine mount arm to the frame horn. Despite the seemingly simple nature of this part, on older cars, it is known to cause massive headaches. Due to its non-insulated design, years of exposure to water, dirt, and road salt will cause the wire to corrode, ultimately leading to complete failure. A break in this cable will cause an open circuit, resulting in issues with the vehicle's electrical system and potentially leading to a no-start condition.

To solve this issue, ECS has engineered an exact-fit, upgraded ground strap for your BMW X5/X6! Unlike its OEM counterpart, this design features insulated, large-gauge copper wire for dependable conductivity and long-lasting durability. Additionally, factory-style lugs are zinc-coated, crimped, and soldered, ensuring protection against corrosion and oxidation.

Whether you're replacing a visibly corroded strap or proactively preventing failure, this solution from ECS is sure to provide lasting performance and protection.

FEATURES

Direct-fit replacement and upgrade for E70 X5 and E71 X6 applications Solves intermittent grounding issues caused by aging OEM straps Clean, stealthy design that fits seamlessly in factory engine bays Factory length and lug orientation for drop-in fitment 2 AWG tinned copper cable for excellent conductivity and corrosion resistance Zinc-coated lugs, crimped and soldered to resist moisture and oxidation Black UL1015-grade insulation withstands oil, heat, and abrasion Discreet ECS label for a clean, OEM+ look Replaces OEM part number 12427557027.

The Schwaben Piston Ring Filer is a vital tool for obtaining the precise end gap necessary for optimal piston ring performance.

This filer allows you to swiftly and accurately file piston rings to exact measurements, enhancing your engine’s efficiency and lifespan. By simply positioning the piston ring and turning the handle, you can easily rotate the abrasive wheel for a smooth and effective filing process.

**Note:** For the Schwaben Universal Piston Ring Compressor, check out T25805755!

Key Features:

• Optimize Performance: Achieve the perfect end gap crucial for top engine efficiency.
• Quick and Precise: File rings to exact specifications with ease.
• Easy Operation: Position the piston ring and turn the handle to effortlessly rotate the abrasive wheel.
• Enhanced Engine Longevity: Accurate end gaps contribute to longer engine life and better performance.

Instructions:

1. Position the Ring: Place the piston ring on the outer edge against the stop and align the ends squarely against the grinding wheel. Apply light, even pressure against the wheel to prevent grinding too large a gap.
2. Operate the Tool: Turn the handle so the grinding wheel turns towards the inside edge of the ring (counter-clockwise when viewed from the handle side of the tool).
3. Exercise Caution: This is a diamond grinding wheel. It cuts fast!

Checking Piston Ring Gap:

1. Deburr the Ring Ends: Carefully remove any burrs on the ring ends before placing the ring in the bore. A light touch with a fine abrasive stone works well.
2. Clean the Rings: Thoroughly clean the rings with lacquer thinner or acetone, as the paint coating from the factory may occasionally scratch the cylinder bore. Always wear gloves during this process.
3. Position the Ring in the Cylinder: Place the ring squarely in the cylinder bore, about 1" down from the deck surface. An upside-down flat-top piston will help you properly square the ring.
4. Measure the End Gap: Use a feeler gauge to measure the ring's end gap. Apply light grinding pressure and check frequently to avoid making the end gap too large.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Looking to update your old torque wrenches? The Schwaben 3/8" Drive Digital Torque Wrench is your answer. 

This digital torque wrench uses an easy-to-read display to show torque amounts and settings, features a push button release, reversible 3/8" drive, 45 tooth ratchet head, and a comfortable no-slip grip and adjustment wheel.

Specifications:

• Setting Range: 45-220 ft lbs (60-300 Nm)
• Display Units: ft-lbs, N-m, Inch-lbs, cm-kg2, and m-kg
• Size: 22" (550mm) length for easy leverage
• Accuracy: +- 3%
• Include blow molded holding case
• Requires one 3V CR2030 battery (included)

Meet modern emission regulations while preserving engine performance with the ECS Baffled Oil Catch Can. Designed for BMW and MINI vehicles, this system efficiently captures blow-by gases, preventing excessive oil vapor ingestion into the intake tract. The innovative 4-chamber baffle system maximizes oil/air separation, reducing carbon build-up and pollutants. Featuring a 1/4" drain fitting for easy maintenance, this catch can minimizes oil deposits, ensuring cleaner emissions and enhanced engine performance.

Key Benefits:

• Efficient 4-chamber baffle system for maximum oil/air separation
• Recirculated design reduces oil ingestion, promoting cleaner emissions
• Durable 6061-T6 billet machined body with anodized black finish for longevity
• Integrated dipstick and sealed reservoir for easy oil inspection and maintenance
• Serviceable design with removable baffle plates for cleaning
• Easy installation with customizable mounting options and leak-free fittings
• Engineered and manufactured in the USA for superior performance and durability

Note: Not for sale or use in the state of California on any pollution-controlled vehicle as per the California Air Resources Board.