VTT is proud to offer our “OBD-LOCK” OBD port locking tool. This is tool is made from billet 6061-T6 aluminum and is designed to completely lock out your OBD port from being accessed. This is useful for people who do not want dealers, techs, etc from accessing their OBD port, and possibly changing a tune, etc. This is also perfect for anti-theft prevention as it will not allow a would-be thief to hook up to the car’s OBD port, duplicate a key, etc. The OBD-LOCK cannot be removed without physically destroying the OBD port if you do not have the proper tools. VTT uses 5 types of screw head designs for every 200 OBD-LOCKS made. This means that worldwide only 40 OBD-LOCKS are using the same head design. For each batch of 200, we redesign the screw heads meaning every batch of 200 OBD-LOCKS will use different screw heads and tools. Each OBD-LOCK sent has its head design chosen at random. After Extensive testing, we have found that our OBD lock fits EVERY SINGLE OBD port we have tried, this means it will fit every single OBD port currently on the market from a high-end BMW to a Ford F150 diesel.
Show More Show Less
VTT is proud to offer their billet replacement for the factory plastic Coolant Reservoir cap. This cap does away with the weak plastic cap while adding some pop, and color to your engine bay. This coolant cap retains ALL of the factory provisions by simply allowing you to snap the factory pressure-relief into the new Billet Cap. VTT also designed these caps to complement their N5X Billet Oil caps, N5XBillet Oil filter housing caps, and Billet Power Steering cap, so all 4 will have the same design. These caps are offered in 4 colors – Red, Black, Blue, and Clear anodized Replaces Genuine BMW Reservoir Cap # 17117639020 Note: Fitment includes 99% of all BMW with a coolant Reservoir tank from the E series forward, meaning then fit even the brand New G8X M3/4 with the S58, all B58, etc. If your BMW is an E90 or newer this cap most likely will fit
Show More Show Less
VTT is proud to offer their billet replacement for the factory plastic Coolant Reservoir cap. This cap does away with the weak plastic cap while adding some pop, and color to your engine bay. This coolant cap retains ALL of the factory provisions by simply allowing you to snap the factory pressure-relief into the new Billet Cap. VTT also designed these caps to complement their N5X Billet Oil caps, N5XBillet Oil filter housing caps, and Billet Power Steering cap, so all 4 will have the same design. These caps are offered in 4 colors – Red, Black, Blue, and Clear anodized Replaces Genuine BMW Reservoir Cap # 17117639020 Note: Fitment includes 99% of all BMW with a coolant Reservoir tank from the E series forward, meaning then fit even the brand New G8X M3/4 with the S58, all B58, etc. If your BMW is an E90 or newer this cap most likely will fit
Show More Show Less
The VTT B58/S58 Head Port Block-Off kit is designed to either seal off the factory head ports used by the OEM low-side PCV system. These ports in the cylinder head utilize engine vacuum to evacuate crankcase gases, but in the process, can allow oil to enter the intake manifold, leading to valve carbon buildup and other performance issues over time. The Block-Off kit offered by VTT completely seals the factory head ports to prevent oil intrusion and unwanted vacuum leaks. This kit does NOT require any tapping, meaning no metal to get into the engine, etc. You simply tap the plugs into place. Key Features Eliminates oil draw-through into the intake manifold Prevents carbon buildup on intake valves Utilizes precision-machined plugs for boost sealing Fully reversible — Block-offs can be removed if needed No tapping is required. Easy install, by tapping the blocks into place.
Show More Show Less
VTT is proud to offer Titanium wheel stud kits for the vehicle owner looking for the lowest possible unsprung weight while maintaining high strength, and good looks. This kit is 60% lighter than factory steel studs and nuts with a total kit of 20 nuts, and studs being 3.1LBS. VTT kit details are as follows: Grade 5 Titanium studs, rated at more than 135,000PSI Tensile Strength Grade 5 Titanium nuts with 60-degree cone seat to fit most all aftermarket wheel applications M5 Hex for easy installation Three Colors Available – Raw, Black, Burnt M14x1.25x75mm on the small end to M14x1.5 on the long end. This will convert M14x1.25 cars into M14x1.5 pattern Installation notes: Apply locktite to the studs (short end) and torque to 20 ft/lb. Lug nuts should be torqued to factory specifications. For safety retorque all hardware (studs and nuts) after 25-50 miles.
Show More Show Less
VTT is proud to offer their billet replacement for the factory plastic Coolant Reservoir cap. This cap does away with the weak plastic cap while adding some pop, and color to your engine bay. This coolant cap retains ALL of the factory provisions by simply allowing you to snap the factory pressure-relief into the new Billet Cap. VTT also designed these caps to complement their N5X Billet Oil caps, N5XBillet Oil filter housing caps, and Billet Power Steering cap, so all 4 will have the same design. These caps are offered in 4 colors – Red, Black, Blue, and Clear anodized Replaces Genuine BMW Reservoir Cap # 17117639020 Note: Fitment includes 99% of all BMW with a coolant Reservoir tank from the E series forward, meaning then fit even the brand New G8X M3/4 with the S58, all B58, etc. If your BMW is an E90 or newer this cap most likely will fit
Show More Show Less
VTT is happy to introduce the first and only available plug and play ONE-WAY crankcase breather kit for BMW S58 applications. With this breather simply remove your oil cap, install the breather, and instantly free up horsepower, improve turbo draining, remove crankcase pressure, all while adding a cool look to your engine bay. FITS with the engine cover on. Engine cover can be removed, and installed without removing the breather. Can be used by itself with the stock PCV system to eliminate crankcase pressure, or with any number of PCV setups, including our VTT Engine catch can for the ultimate in crankcase pressure relief. Made from 6061-T6 Aircraft aluminum anodized black for a long-lasting finish, 4 stainless steel baffles for complete oil control, a PTFE one way check ball, a high-quality filter, and clamp all work together to keep crankcase pressure where it belongs, out of your crankcase. This breather will fit all S58 Vehicles that use the most common oil fill cap design. This does NOT mean it fits all BMW vehicles. The breather sits about 2.5' tall from the valve cover oil cap area, and the filter is 2-3/4' in diameter NOTE: NOT ALL THE S58 MODELS LISTED HAVE THE SAME HOOD CLEARANCE, WE CANNOT SAY WHICH MODELS WILL HAVE CLEARANCE ISSUES AND WHICH WILL NOT AS WE HAVE NOT TESTED FIT ON ALL MODELS. PLEASE TEST CLOSE YOUR HOOD CAREFULLY TO ENSURE CLEARANCE. IF IT DOES NOT FIT LET US KNOW, AND WE WILL GET YOU A REFUND ONCE THE BREATHER IS RETURNED.
Show More Show Less
Do you work on a lot of BMW engines from various platforms? Tired of having to adjust universal engine stand plates to fit your engine? Hate not having access to the flywheel end with the engine on the stand? Vargas answered yes to all of those things and made a tool for anyone that works on BMWs often, and wanted a strong bolt-on engine stand plate that keeps the flywheel end of the engine open! The engine stand plates are machined from a solid billet of 6061-T6 aluminum and anodized in 5 colors for long-lasting corrosion resistance. These are lightweight, and rated for over 1200 lbs!
Show More Show Less
Looking to fix the diff bolt issue on your F9X X3/4M? VTT has taken a 3 pronged approach by offering a triple solution, one part of the solution is the front diff bushing inserts. These are pressed into the factory bushing, and fill the voids in the bushing. This keeps the stock bushing ride compliance but removes any unwanted movement. These are sold as a set Kit includes: Two Billet Bushing inserts Two 46mm Hardened Steel Washers
Show More Show Less
Heat is the enemy of power, and the last thing you want is hot coolant heating your charge air even further right before it enters the charge cooler, but this is what BMW has done on the S58. This is done for emissions and quick warm-up purposes. However, If you are looking to make power on the S58, and are upgrading your charge cooler, or adding PI. While you are there, it takes 30 seconds to remove the coolant lines from the TB connections and replace them with our billet coolant delete kit. This completely removes the coolant from the Throttle body and provides a bypass for the coolant. Simply remove the two lines going to the throttle body, and run our hose in their place. You leave the coolant fittings on the TB open and avoid any unwanted heat being introduced into your charge tract. In our opinion a must for full effort builds. We take the work out of it for you. Kit included: One Plug and Play TB Coolant Delete Hose Kit Features: Billet 6061 Anodized coolant fittings for long leak-free life Reinforced 7-ply silicone hose for strength and longevity Vibration-resistant crimp clamps 100% plug and play, NO cutting or removing factory clamps or hoses. Fully reversible
Show More Show Less
Get rid of the plastic oil cap on your BMW and add some nice billet pop to your engine bay. Look no further than the VTT Billet Oil cap. These are a true Billet oil cap machined from 6061-T6 aluminum and anodized in a variety of colors. These are NOT a thin cap that snaps over your existing oil cap.
Show More Show Less
Soft bushings are the enemy of launching hard, and keeping your drivetrain together. The BMW Transfer Case bushings are notoriously soft, and that is the opposite of what you want when launching a car hard. You can replace the bushing with a solid one, but this is time-consuming usually requires lowering or removing the transfer case, and results in a lot of added NVH. The best path is simply to reduce the amount of flex of the factory bushing so you keep the nice manners when cruising around town, and at idle, but when its time to the launch the transfer case cannot move as it could without the insert. These come as a set of two with 2 bolts to keep them in place. Install time once you get to them is about 2-3 minutes. Could not be easier. Put some lube on them, push them in, and tighten the screws. These are a MUST for high-power G8X, and F9X X3/X4M Builds. All platforms they fit are below. Features: 6061- T6 aluminum construction Easy to install Fully reversible Do not add NVH
Show More Show Less
Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for the B58. VTT B58 Coils are tested against a factory Bosch B58 coil. The VTT performance matches or exceeds the factory B58 Bosch Coil. The coils are offered in a choice of black, red, and blue.
Show More Show Less
These are made from 100% Pre-Preg Carbon Fiber for a perfect fit. The carbon fiber gives it just the right look to add to your performance vehicle! Each holder has dual Suction cups and will stick to any smooth surface. We suggest mounting them in the upper left or right corner of your windshield with a full view of the sky. Dragy holder features Stop your Dragy from flying off the dash and having to search for it Position your Dragy in the optimal position for the best satellite coverage VTT Dragy holder exposes the entire top of the Dragy so nothing is blocking the receiver from the Satellite The charging port is not blocked and can be accessed with the cover on
Show More Show Less
Get rid of the plastic oil cap on your BMW and add some nice billet pop to your engine bay. Look no further than the VTT Billet Oil cap. These are a true Billet oil cap machined from 6061-T6 aluminum and anodized in a variety of colors. These are NOT a thin cap that snaps over your existing oil cap.
Show More Show Less
VTT noticed a hole in the F9X X3/4M market for a high-quality, lightweight, NVH-friendly, and easy-to-install Diff Lock Down kit to improve diff stability under launching, and hard cornering. So we did something about it and went to work on a very innovative design that 100% positively locks the diff down from movement, while shielding it from adding a ton of NVH, and can be used with the stock diff, and subframe bushings. This design uses existing mounting points on the vehicle, you do NOT have to remove the subframe or the Diff to install. Simply remove 4 differential bolts, drill two holes in the subframe slightly bigger, install two M8 riv-nuts, and install the lockdown, you do not even have to move the exhaust. A typical install can be 30-45 minutes for someone who is experienced working on vehicles, an hour or two if you like taking it slow. Features: Lightweight 1.5 lbs for the entire lockdown plate Uses FOUR connection points on the Diff, and three on the subframe for the ultimate in positive diff location, this will stop all diff movement on launch, saving your guibos, etc 100% Billet construction from 6061-T6 aluminum Anodized in 3 colors for corrosion resistance, a long-lasting finish, and good looks The subframe does NOT have to be removed for installation Uses all 12.9 grade hardware Does not add excessive NVH Positively locks down the diff to eliminate all unwanted movement under launches, acceleration, cornering, etc.
Show More Show Less
VTT is proud to offer their billet replacement for the factory plastic Coolant Reservoir cap. This cap does away with the weak plastic cap while adding some pop, and color to your engine bay. This coolant cap retains ALL of the factory provisions by simply allowing you to snap the factory pressure-relief into the new Billet Cap. VTT also designed these caps to complement their N5X Billet Oil caps, N5XBillet Oil filter housing caps, and Billet Power Steering cap, so all 4 will have the same design. These caps are offered in 4 colors – Red, Black, Blue, and Clear anodized Replaces Genuine BMW Reservoir Cap # 17117639020 Note: Fitment includes 99% of all BMW with a coolant Reservoir tank from the E series forward, meaning then fit even the brand New G8X M3/4 with the S58, all B58, etc. If your BMW is an E90 or newer this cap most likely will fit
Show More Show Less
This VTT charge air cooler is perfectly designed to reduce heat soak and increase power and efficiency! This increased airflow lets the engine breathe better and perform under hard and light acceleration. The team at VTT was able to take the limited space given to them by the factory, and add not only a larger more efficient core, but also much better-designed/flowing runners, and end tanks.
Show More Show Less
This VTT charge air cooler is perfectly designed to reduce heat soak and increase power and efficiency! This increased airflow lets the engine breathe better and perform under hard and light acceleration. The team at VTT was able to take the limited space given to them by the factory, and add not only a larger more efficient core, but also much better-designed/flowing runners, and end tanks.
Show More Show Less
Vargas has contacted multiple coil manufacturing companies, paying for individual coils to be made then putting them through rigorous testing in the USA to ensure they matched or exceeded factory output. Once satisfied with the testing, the best performing coils were made to various colors and specs. Vargas is proud to offer a new line of ignition coil replacements for the B58. VTT B58 Coils are tested against a factory Bosch B58 coil. The VTT performance matches or exceeds the factory B58 Bosch Coil. The coils are offered in a choice of black, red, and blue.
Show More Show Less
These are made from molded plastic for a perfect fit. Each holder has dual Suction cups and will stick to any smooth surface. We suggest mounting them in the upper left or right corner of your windshield with a full view of the sky. Dragy holder features Stop your Dragy from flying off the dash and having to search for it Position your Dragy in the optimal position for the best satellite coverage VTT Dragy holder exposes the entire top of the Dragy so nothing is blocking the receiver from the Satellite The charging port is not blocked and can be accessed with the cover on
Show More Show Less
This VTT charge air cooler is perfectly designed to reduce heat soak and increase power and efficiency! This increased airflow lets the engine breathe better and perform under hard and light acceleration. The team at VTT was able to take the limited space given to them by the factory, and add not only a larger more efficient core, but also much better-designed/flowing runners, and end tanks.
Show More Show Less
While BMW did a beautiful job on the F9X X3/4M’s they sure decided to get cheap out on the strut bars. Ugly steel bars with no real pop or aesthetically pleasing qualities seem like an afterthought to such a well-thought-out car. Well, here at VTT we decided to do something about it, and immediately took our bars off, and let our engineers go to work on a solution. What they came up with is beautiful, and functional. 100% CNc machined from 6061-T6 aluminum and anodized in a variety of colors The result adds a gorgeous look to your X3/4M engine bay, and what BMW should have done from the factory.
Show More Show Less
This VTT charge air cooler is perfectly designed to reduce heat soak and increase power and efficiency! This increased airflow lets the engine breathe better and perform under hard and light acceleration. The team at VTT was able to take the limited space given to them by the factory, and add not only a larger more efficient core, but also much better-designed/flowing runners, and end tanks
Show More Show Less
Get rid of the plastic oil cap on your BMW and add some nice billet pop to your engine bay. Look no further than the VTT Billet Oil cap. These are a true Billet oil cap machined from 6061-T6 aluminum and anodized in a variety of colors. These are NOT a thin cap that snaps over your existing oil cap.
Show More Show Less
The VTT S58 Head Port Check Valve Kit is designed to convert the factory head ports used by the OEM low-side PCV system. These ports in the cylinder head utilize engine vacuum to evacuate crankcase gases, but in the process, can allow oil to enter the intake manifold, leading to valve carbon buildup and other performance issues over time. VTT's Billet Check Valve kit converts the head ports into a robust internal PCV system using precision-engineered check valves. These one-way valves allow vacuum to function as intended while blocking boost pressure from entering the crankcase or charge tract.
Show More Show Less
For dedicated drag racing applications where every ounce of weight and simplicity matters, the VTT S58 Remote Oil Plate is the ultimate "delete" solution.
Engineered for those who demand total control over their PCV system, the VTT Screw-In Oil Cap Adapter provides a robust solution for crankcase ventilation.
The VTT-FAB Billet MAP Sensor Bung is the definitive choice for tuners and fabricators seeking a reliable mounting solution for B48, B58, and S58 platforms.
The VTT 6-Bar MAP sensor kit provides the necessary overhead to monitor boost levels with a linear voltage scale that makes software calibration straightforward.
The VTT High Performance Drop-In Air Filter is the ultimate solution for BMW X3M and X4M owners looking to unlock hidden power without the complexity of a full intake system.
The VTT-FAB-038 Billet Front Oil Feed Block-Off is a precision-engineered solution for enthusiasts and fabricators building custom turbocharger systems.
The Vargas EWG Actuator Bracket is the definitive solution for enthusiasts looking to merge BMW’s advanced factory EWG control with the high-performance capabilities of Garrett G-Series turbochargers.
Show More Show Less
