BMW Internal Engine Parts

VTT S55 Crank Bolt Capture - F8X S55 F3x N55

2X Entries Into Our F80 M3 Sweepstakes

T#:557934

Part#: VTT-S55-CBC

In Stock

$ 129.99 USD

Add to Wish List

Qty

$ 129.99 USD

Add to Wish List

The S55 suffers from a weak point in its crankshaft. It has been reported that when increasing the power to the engine, the crank hub can move or spin slightly under an extreme load.

Vargas "Spline Lock" Crank Hub Solution - Includes Crank Bolt Capture...

2X Entries Into Our F80 M3 Sweepstakes

T#:558795

Part#: VTT-CRANKHUB-1

Ships in 1-2 days

$ 889.99 USD

Add to Wish List

Qty

$ 889.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Rein Piston Rings - Set - Single Piston - E36, Z3

2X Entries Into Our F80 M3 Sweepstakes

T#:591603

Part#: 11251405783

Back Ordered

$ 43.99 USD

Add to Wish List

Qty

$ 43.99 USD

Add to Wish List

Replace your worn out piston rings with OE replacements - 86.415mm

Oil Pump Chain - E36 E46 E34 E39 Z3 Z4

T#:14529

Part#: 11417576915

In Stock

$ 52.99 USD

Add to Wish List

Qty

$ 52.99 USD

Add to Wish List

This is an OEM oil pump chain for BMW's with the M50/M52/M54/S50/S52 6 cylinder engine. We recommend replacing the oil pump chain any time you remove the oil pump from the car.

IWIS is a leader in complex engine parts. Using advanced techniques in research and design allows IWIS to offer parts that not only repair but ultimately improve the way your engine runs.

This item fits the following BMWs:
1992-1998 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
1991-1995 E34 BMW 525i
1997-2003 E39 BMW 525i 528i 530i
2004-2005 E60 BMW 525i 530i
2004-2005 E83 BMW X3 2.5i X3 3.0i
1996-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i
1998-2000 Z3 BMW M Roadster M Coupe
2003-2006 E85 BMW Z4 2.5i Z4 3.0i

Show More Show Less

Spline Lock Crank Hub Solution W/ Complete Package - N55 S55 ...

2X Entries Into Our F80 M3 Sweepstakes

T#:18733532

Part#: VTT-CRANKHUB-6

Ships in 1 Business Day

$ 986.99

This product was last offered at the strikethrough price on
06-28-2026

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Rein Piston Rings - Set - Single Piston

2X Entries Into Our F80 M3 Sweepstakes

T#:592808

Part#: 11251247917

Ships in 3 Business Days

$ 36.99 USD

Add to Wish List

Qty

$ 36.99 USD

Add to Wish List

Replace your worn out piston rings with OE replacements - 85.065mm

Camshaft Timing Chain - E39 E38 E53 X5 with M62 V8 engine

T#:14505

Part#: 11311747437

In Stock

$ 54.99 USD

Add to Wish List

Qty

$ 54.99 USD

Add to Wish List

This is the timing chain that connects the 2 camshaft sprockets. The M62 V8 engine is known for issues with the timing system. Replace the timing chain on your BMW with this OEM part. We also recommend replacing guides and tensioners while replacing the chain. Sold individually. 2 per car.

IWIS is a leader in complex engine parts. Using advanced techniques in research and design allows IWIS to offer parts that not only repair but ultimately improve the way your engine runs.

This item fits the following BMWs:
1997-2003 E39 BMW 540i
1996-2001 E38 BMW 740i 740il
1996-1999 E31 BMW 840i 840ci
2000-2003 E53 BMW X5 4.4i X5 4.6is

Show More Show Less

OEM IWIS Lower Timing Chain - E36, E46, E39, Z3 E60

T#:362220

Part#: 11311432176

In Stock

$ 83.99

This product was last offered at the strikethrough price on
06-08-2026

$ 79.99 USD

Add to Wish List

Qty

$ 79.99 USD

Add to Wish List

IWIS is a leader in complex engine parts. Using advanced techniques in research and design allows IWIS to offer parts that not only repair, but ultimately improve the way your engine runs.

Rein Piston Ring - Priced Per Piston - E28, E30, E34, E36

2X Entries Into Our F80 M3 Sweepstakes

T#:379806

Part#: 11251713192

Ships in 3 Business Days

$ 30.99 USD

Add to Wish List

Qty

$ 30.99 USD

Add to Wish List

For use on stock pistons, will need 6 sets to replace all piston rings in the engine

Rein Piston Ring Set

2X Entries Into Our F80 M3 Sweepstakes

T#:379819

Part#: 11251437077

Ships in 3 Business Days

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

Standard bore replacement piston rings

Rein Piston Ring Set - Priced Per Piston

2X Entries Into Our F80 M3 Sweepstakes

T#:592811

Part#: 11251713178

Ships in 3 Business Days

$ 28.99 USD

Add to Wish List

Qty

$ 28.99 USD

Add to Wish List

Replace your worn rings - 84.000mm

Oil Pump Chain - E46 M3, Z3M Z4M with S54 engine

T#:34869

Part#: 11411401399

In Stock

$ 30.99

This product was last offered at the strikethrough price on
06-19-2026

$ 29.99 USD

Add to Wish List

Qty

$ 29.99 USD

Add to Wish List

This is an OEM oil pump chain for BMW's with the S54 6 cylinder engine. We recommend replacing the oil pump chain any time you remove the oil pump from the car.

IWIS is a leader in complex engine parts. Using advanced techniques in research and design allows IWIS to offer parts that not only repair, but ultimately improve the way your engine runs.

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

N54 Spline Lock Crank Hub Solution With Complete Package

2X Entries Into Our F80 M3 Sweepstakes

T#:18733525

Part#: VTT-CRANKHUB-3

Ships in 3 Business Days

$ 939.99 USD

Add to Wish List

Qty

$ 939.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Spline N55 S55 Lock Crank Hub Solution W/ Hardware Package

2X Entries Into Our F80 M3 Sweepstakes

T#:18733531

Part#: VTT-CRANKHUB-5

Ships in 10 Business Days

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Crankshaft to Camshafts Lower Timing Chain - E39 E38 E53 E31 ...

T#:14503

Part#: 11311741746

In Stock

$ 97.72

This product was last offered at the strikethrough price on
07-16-2026

$ 88.99 USD

Add to Wish List

Qty

$ 88.99 USD

Add to Wish List

This is the timing chain that connects the crankshaft to the camshafts. The M62 V8 engine is known for issues with the timing system. Replace the timing chain on your BMW with this OEM part. We also recommend replacing guides and tensioners while replacing the chain.

IWIS is a leader in complex engine parts. Using advanced techniques in research and design allows IWIS to offer parts that not only repair but ultimately improve the way your engine runs.

This item fits the following BMWs:
1997-2003 E39 BMW 540i
1996-2001 E38 BMW 740i 740il
1996-1999 E31 BMW 840i 840ci
2000-2003 E53 BMW X5 4.4i X5 4.6is

Show More Show Less

Genuine MINI Shaft Seal

T#:405713

Part#: 11117568264

In Stock

27% off MSRP $ 55.36

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 40.59 USD

Add to Wish List

Qty

27% off MSRP

$ 55.36

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 40.59 USD

Add to Wish List

Genuine MINI Hub

T#:406420

Part#: 11237537697

In Stock

$ 73.99 USD

Add to Wish List

Qty

$ 73.99 USD

Add to Wish List

Genuine MINI Crankshaft Sprocket

T#:32419

Part#: 11211485402

Ships in 3 Business Days

6% off MSRP $ 76.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 71.99 USD

Add to Wish List

Qty

6% off MSRP

$ 76.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 71.99 USD

Add to Wish List

Genuine MINI SPROCKET
Fits BMW Engines including:
W10,W11

Rein Piston Rings - Set - Single Piston - E30, E36

2X Entries Into Our F80 M3 Sweepstakes

T#:591604

Part#: 11251727461

Back Ordered

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

Replace your worn out piston rings with OE replacements - 84.000mm

Spline Lock Crank Hub Solution W/ Crank Bolt Capture - N54

2X Entries Into Our F80 M3 Sweepstakes

T#:18733527

Part#: VTT-CRANKHUB-2

Ships in 10 Business Days

$ 871.99 USD

Add to Wish List

Qty

$ 871.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Spline Lock Crank Hub Solution W/ Hardware Package - N54

2X Entries Into Our F80 M3 Sweepstakes

T#:18733526

Part#: VTT-CRANKHUB-4

Ships in 10 Business Days

$ 880.99 USD

Add to Wish List

Qty

$ 880.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution.

Show More Show Less

Spline Lock Crank Hub Solution

2X Entries Into Our F80 M3 Sweepstakes

T#:8061334

Part#: VTT-N55-CRANKHUB

Ships in 10 Business Days

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Under certain conditions, the N55 crank hub likes to spin, without warning and even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and ECS are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

Vargas "Spline Lock" Crank Hub Solution - N54

2X Entries Into Our F80 M3 Sweepstakes

T#:558924

Part#: VTT-N54-CRANKHUB

Ships in 10 Business Days

$ 818.99 USD

Add to Wish List

Qty

$ 818.99 USD

Add to Wish List

Anyone with a modified N54 knows the risks involved. Upping the performance of any engine can come with some inherent risk; if we add more boost but not fuel, detonation will occur (or worse). Furthermore, improper installation, maintenance, or operation can turn a perfectly healthy engine into a paperweight. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The worst failures, however, are the ones we don't plan for. When the engine simply can't handle the stresses its put under, or the design is such that it simply does not support extreme conditions. Enter the N54 crank hub. Under certain conditions, it likes to spin without warning, even when the engine is in perfect health. The engineers at Vargas saw and dealt with this problem time and again, and they saw fit to do something about it. This hub uses a proprietary "Spline Lock" technology that uses high tolerance machined splines that press into the crank and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). Vargas spent many months testing, and retesting this design, utilizing well over 10 different samples to come to the final production version. During testing, the final hub managed to break the testing rig before slipping. These have been bench-tested, and real-world tested on the VTT N54 race car spinning 8K RPM, and making well over 900WHP. Features: Installs the same as a stock hub Does NOT require the crank to be drilled for pins Manufactured from Harndered 17-4SS We suggest the Crank Hub System ONLY be installed by a qualified shop or technician. Timing tools are 100% REQUIRED if installed improperly engine damage may occur. DISCLAIMER: VTT and Turner Motorsport are not responsible for any engine damage caused by improper installation, or misuse of the crank hub solution. The product comes with a 1-year unlimited mileage warranty from manufacturer defects.

Show More Show Less

VTT N54 “Spline Lock” CrankHub Solution Package W/ Crank Bolt Cap...

2X Entries Into Our F80 M3 Sweepstakes

T#:19395579

Part#: VTTCRANKHUBPKG

Ships in 10 Business Days

$ 934.99 USD

Add to Wish List

Qty

$ 934.99 USD

Add to Wish List

VTT is proud to offer the only complete N54 complete crank hub solution that does NOT require the crank to be drilled for pins. Our hub uses our proprietary “Spline Lock” technology that uses high tolerance machined splines which press into the crank, and positively lock the hub to the crank. The splines are machined in such a way that rotational forces drive the hub, and splines deeper into the crank meaning when the hub encounters a situation that would normally slip a stock hub the splined hub is driven into the crank to keep it in place (much like a splined extractor). We spent many months testing, and retesting this design, utilizing well over 10 different samples to come to our final production version. During testing, our final hub managed to break our testing rig before slipping. These have been bench tested, and real-world tested on the VTT N54 race car spinning 8K RPM and making well over 900WHP. This technology means our hub installs the same as a stock hub, no drilling of the crank, which means MUCH less labor is involved and is reversible is ever wanting to be uninstalled leaving no holes in the crank. The “Spline Lock” is ONLY available with the VTT Crank bolt capture for the ULTIMATE Crank Hub solution for your BMW. These parts are designed to be used together, and the spline lock should not run without the CBC VTT “Spline Lock” Crank hubs are CNC manufactured from 440C tool Steel with a Rockwell rating of HRC60 for the ultimate in durability, and toughness. Hub Plus OEM bolt OEM Oil pump sprocket OEM oil sprocket retainer VTT Crank bolt capture

Show More Show Less

Genuine MINI Impulse Sending Wheel

T#:515028

Part#: 11227634295

In Stock

7% off MSRP $ 97.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 90.99 USD

Add to Wish List

Qty

7% off MSRP

$ 97.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 90.99 USD

Add to Wish List

Genuine MINI Cylinder Head Bolts - Set Of 13

T#:405907

Part#: 11127560274

Ships in 1 day

19% off MSRP $ 89.76

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 72.75 USD

Add to Wish List

Qty

19% off MSRP

$ 89.76

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 72.75 USD

Add to Wish List

Genuine MINI Shaft Seal

T#:405712

Part#: 11117568263

Ships in 1 day

26% off MSRP $ 58.10

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 42.79 USD

Add to Wish List

Qty

26% off MSRP

$ 58.10

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 42.79 USD

Add to Wish List

Genuine MINI Exhaust Valve

T#:407264

Part#: 11347547187

In Stock

6% off MSRP $ 65.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 61.99 USD

Add to Wish List

Qty

6% off MSRP

$ 65.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 61.99 USD

Add to Wish List

Genuine MINI Camshaft Sprocket - SOHC

T#:33887

Part#: 11311485403

Ships in 1 day

$ 128.99 USD

Add to Wish List

Qty

$ 128.99 USD

Add to Wish List

Genuine MINI SPROCKET
Fits BMW Engines including:
W10,W11

Genuine MINI Hex Bolt With Washer

T#:29202

Part#: 07137829910

Ships in 1 day

2% off MSRP $ 43.63

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 42.86 USD

Add to Wish List

Qty

2% off MSRP

$ 43.63

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 42.86 USD

Add to Wish List

Genuine MINI HEX BOLT WITH WASHER

Genuine MINI Crankshaft Gear

T#:510222

Part#: 11217588996

In Stock

3% off MSRP $ 33.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 31.95 USD

Add to Wish List

Qty

3% off MSRP

$ 33.00

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 31.95 USD

Add to Wish List

Timing Chain - Upper

T#:362341

Part#: 11311432177

In Stock

$ 45.92

This product was last offered at the strikethrough price on
08-23-2026

$ 37.99 USD

Add to Wish List

Qty

$ 37.99 USD

Add to Wish List

This is the upper timing chain that connects the 2 camshaft sprockets on cars with the M50, M52, M54, S50 or S52 engines. If you need the lower timing chain that connects the crankshaft to the upper sprocket you can find it Here .

IWIS is a leader in complex engine parts. Using advanced techniques in research and design allows IWIS to offer parts that not only repair but ultimately improve the way your engine runs.

This item fits the following BMWs:
1992-1998 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
1991-1995 E34 BMW 525i
1997-2003 E39 BMW 525i 528i 530i
2004-2005 E60 BMW 525i 530i
2004-2006 E83 BMW X3 2.5i X3 3.0i
2000-2006 E53 BMW X5 3.0i
1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i
1997-2000 Z3 BMW Z3 M Roadster M Coupe
2003-2005 E85 BMW Z4 2.5i Z4 3.0i

Show More Show Less

Cylinder Head - N16

T#:15777325

Part#: 11122470427

Ships in 6 Business Days

6% off MSRP $ 4,526.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 4,234.99 USD

Add to Wish List

Qty

6% off MSRP

$ 4,526.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 4,234.99 USD

Add to Wish List

Introducing the Genuine Mini Cylinder Head (Part Number: 11122470427) for your Mini Cooper – the ultimate solution to enhance your engine's performance and reliability.

Precision-engineered to exacting standards, this cylinder head is an authentic replacement part from Genuine Mini, ensuring seamless compatibility and a perfect fit for your Mini Cooper. Crafted with the utmost attention to detail, it's designed to deliver exceptional combustion efficiency, improving power output and fuel economy.

Whether you're looking to replace a worn-out cylinder head or boost your Mini Cooper's performance, this Genuine Mini Cylinder Head is the ideal choice. Rest assured that you're investing in a top-quality component that meets the highest industry standards, backed by the reputation of Genuine Mini for excellence.

Upgrade your Mini Cooper's engine with the Genuine Mini Cylinder Head (Part Number: 11122470427) and experience the perfect balance of performance, durability, and reliability. It's time to unleash the full potential of your Mini Cooper with this authentic and high-quality component.

Show More Show Less

Rein Exhaust Valve - E34, E36, E39, E46, Z3

2X Entries Into Our F80 M3 Sweepstakes

T#:379738

Part#: 11341739823

Ships on Oct 27, 2026

$ 20.99 USD

Add to Wish List

Qty

$ 20.99 USD

Add to Wish List

Replacement exhaust valve

Genuine MINI Piston W/ Rings - ( 0 Size ) Priced Each

T#:33527

Part#: 11257566019

Ships in 6 Business Days

10% off MSRP $ 414.20

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 370.99 USD

Add to Wish List

Qty

10% off MSRP

$ 414.20

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 370.99 USD

Add to Wish List

Genuine MINI MAHLE PISTON
Fits BMW Engines including:
N14

Genuine Mini Hex Bolt With Washer R5X R6X - Priced Each

T#:405708

Part#: 11117540160

In Stock

$ 9.99 USD

Add to Wish List

Qty

$ 9.99 USD

Add to Wish List

Upgrade your Mini's engine with this high-quality Hex Bolt With Washer designed to attach the bottom engine crank housing to the top engine block. This essential component ensures a secure connection between engine parts, enhancing overall performance and reliability. Trust this genuine Mini part for optimal fit and function in your Mini vehicle.

Enhances engine performance
Ensures secure attachment between engine components
Genuine Mini part for optimal fit and reliability
Easy to install for quick replacement

Show More Show Less

Aluminum Cylinder Head Bolt Set

2X Entries Into Our F80 M3 Sweepstakes

T#:594302

Part#: 11120392547

In Stock

$ 12.99

This product was last offered at the strikethrough price on
08-13-2026

$ 7.89 USD

Add to Wish List

Qty

$ 7.89 USD

Add to Wish List

If you remove your cylinder head replacement head bolts are a must. These bolts are designed to be torqued down and not reused.

Connecting Rod Bolt - Priced Each

T#:512851

Part#: 11247593922

In Stock

$ 3.99 USD

Add to Wish List

Qty

$ 3.99 USD

Add to Wish List

Elevate your Mini's engine performance with the connecting rod bolt, essential for securing the connecting rod's bottom half to the rod itself. This vital component ensures the stability and integrity of the engine's operation, providing reliability and optimal functionality.

Crucial for connecting rod stability
Ensures secure attachment of rod components
Essential for engine integrity and reliability
Optimizes engine functionality and performance

Show More Show Less

Rein Exhaust Valve - Sold Each - E28, E30, E34

2X Entries Into Our F80 M3 Sweepstakes

T#:584424

Part#: 11341708896

In Stock

Sale - Save 9% $ 18.35

This product was last offered at the strikethrough price on
05-14-2026

$ 16.65 USD

Add to Wish List

Qty

Sale - Save 9%

$ 18.35

This product was last offered at the strikethrough price on
05-14-2026

$ 16.65 USD

Add to Wish List

Replace your worn valves

OEM Rein Camshaft / Crankshaft Sensor O-Ring - Multiple BMWs ...

2X Entries Into Our F80 M3 Sweepstakes

T#:12463

Part#: 12141748398

In Stock

$ 4.99

This product was last offered at the strikethrough price on
06-29-2026

$ 2.75 USD

Add to Wish List

Qty

$ 2.75 USD

Add to Wish List

This is the o-ring used for most BMW camshaft sensors and crankshaft sensors. Although most sensors that we sell come with this o-ring at no charge, they may be the source of oil or fluid leaks.

RECTANGRING

T#:511589

Part#: 11317587757

Ships in 3 Business Days

2% off MSRP $ 8.50

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 8.37 USD

Add to Wish List

Qty

2% off MSRP

$ 8.50

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 8.37 USD

Add to Wish List

Genuine MINI Hex Bolt With Washer - 07147543890

T#:29902

Part#: 07147543890

In Stock

$ 3.99 USD

Add to Wish List

Qty

$ 3.99 USD

Add to Wish List

Ensure the secure assembly of components in your Mini with the Genuine MINI Hex Bolt With Washer - 07147543890. This high-quality bolt and washer combination is designed specifically for Mini vehicles, providing reliability and peace of mind for various automotive applications.

Genuine OEM part ensures compatibility and fitment
High-quality construction for durability and longevity
Designed to meet Mini's specifications and standards
Ideal for various assembly and maintenance tasks in your Mini

Genuine MINI HEX BOLT WITH WASHER

Show More Show Less

Genuine MINI Connecting Rod Bolt L=45mm - 11241485407

T#:32992

Part#: 11241485407

In Stock

14% off MSRP $ 6.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 5.99 USD

Limited Qty Sale

Add to Wish List

Qty

14% off MSRP

$ 6.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 5.99 USD

Limited Qty Sale

Add to Wish List

Genuine MINI CONNECTING ROD BOLT
Fits BMW Engines including:
W10,W11

Timing Chain - E30 E32 E34

T#:4468

Part#: 11311716986

Ships in 1 Business Day

$ 47.17 USD

Add to Wish List

Qty

$ 47.17 USD

Add to Wish List

This single row timing chain is used on many BMW's from 1979 on. If you are rebuilding your engine we recommend replacing the timing chain.

IWIS is a leader in complex engine parts. Using advanced techniques in research and design allows IWIS to offer parts that not only repair, but ultimately improve the way your engine runs.

This item fits the following BMWs:
1979-1983 E21 BMW 320i 323i
1984-1985 E30 BMW 318i
1979-1981 E12 BMW 528i 530i
1985-1988 E28 BMW 533i 535i 535is
1989-1995 E34 BMW 535i
1979-1989 E24 BMW 633csi 635csi
1979-1987 E23 BMW 733i 735i
1988-1993 E32 BMW 735i 735il

Show More Show Less

Timing Chain - Single Row

T#:578660

Part#: 11311716987

In Stock at Vendor

$ 62.99

This product was last offered at the strikethrough price on
05-07-2026

$ 60.99 USD

Add to Wish List

Qty

$ 60.99 USD

Add to Wish List

The timing chain in any vehicle can begin to stretch and rattle over time. This is a common issue, and though BMW says it is a lifetime part, most enthusiasts decide to change them. If you need only the timing chain instead of a kit, ECS Tuning has your replacement. This is a direct fit replacement for any broken or stretched chain. A great replacement to a damaged chain or one that may have been misplaced out of a timing belt kit.

Show More Show Less

Piston Ring - Priced Per Piston | BMW M54 3.0L Engine

2X Entries Into Our F80 M3 Sweepstakes

T#:591606

Part#: 11257506252

Ships in 3 Business Days

$ 48.99 USD

Add to Wish List

Qty

$ 48.99 USD

Add to Wish List

Piston Ring - Priced Per Piston | BMW M54 3.0L Engine is a vital component in maintaining proper compression and oil control in BMW M54 3.0L engines. Over time, piston rings experience wear from continuous movement within the cylinder bore, leading to decreased engine efficiency. Worn or damaged rings can result in excessive oil consumption, reduced performance, and visible black or blue smoke from the exhaust. Ideal for engine rebuilds, this high-quality replacement ensures optimal sealing and longevity.

Restores proper compression and oil control for improved engine performance
Reduces oil consumption and minimizes exhaust smoke
Direct-fit replacement for BMW M54 3.0L engine pistons
Manufactured from high-strength materials for durability and longevity
Essential for engine rebuilds and maintaining peak efficiency
Designed to withstand high temperatures and pressures for reliable operation

Show More Show Less

Rein Alusil Piston Ring Repair Kit - E38, E39, E53

2X Entries Into Our F80 M3 Sweepstakes

T#:591608

Part#: 11259071606

Ships in 3 Business Days

$ 37.99 USD

Add to Wish List

Qty

$ 37.99 USD

Add to Wish List

Set of rings for one piston

OEM Rein Rocker Arm Shaft Plug - E28 E30 E34

2X Entries Into Our F80 M3 Sweepstakes

T#:583592

Part#: 11331264519

In Stock at Vendor

$ 6.11 USD

Add to Wish List

Qty

$ 6.11 USD

Add to Wish List

This is an OEM Rein replacement rocker arm shaft plug, also referred to by BMW as a Blind Plug. This plug connects to the end of the rocker arm shafts. 4 required per vehicle. Replace your old plugs to keep everything properly sealed.

Show More Show Less

Genuine MINI N18 1.6L Adjustment Sprocket Unit - Outlet Cam

T#:407311

Part#: 11367536085

Ships in 1 day

6% off MSRP $ 674.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 633.99 USD

Add to Wish List

Qty

6% off MSRP

$ 674.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 633.99 USD

Add to Wish List

Genuine MINI N18 1.6L Adjustment Sprocket Unit - Outlet Cam

Upgrade your Mini's performance with the Genuine MINI N18 1.6L Adjustment Sprocket Unit - Outlet Cam. Engineered with precision, this adjustment sprocket unit ensures precise timing for improved engine efficiency. Its durable construction and easy installation make it an ideal choice for Mini owners looking to enhance their driving experience.

Optimizes engine performance
Ensures precise timing
Durable construction
Easy installation

Show More Show Less

Genuine MINI Adjustment Unit - Inlet Cam

T#:407314

Part#: 11367545862

Ships in 1 day

6% off MSRP $ 674.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 633.99 USD

Add to Wish List

Qty

6% off MSRP

$ 674.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 633.99 USD

Add to Wish List

Project Cars

SELECT YOUR BMW

Sub-Categories

Genuine MINI N18 1.6L Adjustment Sprocket Unit - Outlet Cam

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results