Oil Separation & Breather System

When your CPV O-ring fails it causes a slow oil leak on the passenger side of the engine, making an oily mess that frequently resembles a rear main seal leak. Replacing the CPV with an upgraded o-ring ensures a long-term solution to this common problem. 

The factory o-ring over time fails from heat cycling and oil exposure due to the Buna rubber used in OEM o-rings, while the included Viton Fluoroelastomer is resistant to a much higher temperature to ensure prolonged life without leaking. 

Turner Motorsport presents the Crankcase Ventilation System Refresh Kit for BMW owners experiencing malfunctioning or aged CCV systems. This comprehensive kit includes all necessary hoses to complete a refresh, ensuring optimal performance and reliability for your BMW's CCV system.

• Addresses malfunctioning CCV systems
• Ensures proper ventilation of the crankcase
• Comprehensive kit includes all necessary hoses
• Restores performance and reliability
• Compatible with various BMW models

On M52/S52-equipped BMWs, the factory crankcase ventilation (CCV) system is a notorious weak link. Between brittle plastic corrugated hoses that crumble from heat soak and an internal cyclone diaphragm prone to tearing, a failing CCV leads to massive oil consumption, vacuum leaks, and that dreaded "howling" whistle.

This kit addresses these issues with all new components and hardware. Both oil separator hoses, the cyclone separator itself, the mounting grommet, and the retaining bolts are included. Servicing this system is guaranteed to restore performance lost as a result of worn CCV components.

Kit includes:

Cyclone Separator/Crankcase Pressure Regulator Valve High Performance Silicone Breather Hose Return Hose Mounting Grommet Hex Bolt (3)

BMW Oil Separator Valve | M60 3.0 / 4.0L is a vital component that ensures proper crankcase ventilation by separating oil vapors from blow-by gases, preventing excessive oil consumption and maintaining engine efficiency. Designed for BMW models equipped with the M60 3.0L and 4.0L engines, this oil separator valve helps reduce carbon buildup and extends the life of essential engine components. For optimal results, it is recommended to replace the valve cover and crankcase ventilation system (CCV) when changing the separator valve.

• Effectively separates oil vapors to prevent excessive oil consumption
• Helps maintain proper crankcase ventilation for optimal engine performance
• Reduces carbon buildup and prolongs engine longevity
• Direct-fit replacement for BMW M60 3.0L and 4.0L engines
• High-quality materials ensure durability and resistance to engine heat
• Recommended to replace valve cover and CCV for complete system maintenance

Ensure the longevity and efficiency of your BMW engine by replacing a worn oil separator valve with this high-quality replacement.

BMW N63 4.4L Vent Pipe

The BMW N63 4.4L Vent Pipe addresses common issues with oil separators freezing in cold weather conditions. This problem often occurs if the vehicle is driven before it is fully warmed up, leading to a howling noise and multiple oil leaks. The crankcase breather valve in the vent pipe purges oil vapor from the engine block into the valve cover. However, condensation can sometimes cause the valve to freeze, which may result in the oil separator system failing, cracking, or disintegrating. This replacement vent pipe ensures proper function and prevents costly damage by maintaining the integrity of the oil separator system.

Benefits:

• Prevents Freezing Issues: Reduces the risk of oil separator failure in cold weather conditions.
• Eliminates Oil Leaks: Helps prevent leaks caused by frozen oil separators.
• Ensures Proper Ventilation: Maintains effective purging of oil vapor from the engine block.
• Durable Construction: Built to withstand harsh weather conditions and engine stress.
• Direct Replacement: Designed to fit seamlessly with BMW N63 4.4L engines.

Vargas Turbo has you covered when you are installing a custom turbo setup. With all of the adapters you need and all the valves necessary, the only real limiting factor is your imagination!

This is a 1/2" (fits -8AN hos perfectly as well) CNC Billet check valve that can be used for a variety of uses including a vacuum/boost check valve when removing the stock PCV system, and still wanting to run the vacuum to the crankcase. Rated at over 100 psi, with a cracking psi of .25psi.

This part fits the following BMW engines:
2006-2012 N54

The plastic hoses and oil separator can crack or become faulty, leading to vacuum leaks or oil leaks. This is caused by the stress the plastic components are exposed to during heating and cooling cycles, especially if the vehicle is not brought up to operating temperature during driving in cold weather climates.

This kit includes the needed hoses, oil separator, mounting grommet, and hardware.

Fits the following BMWs:
2000-2003 E39 BMW 530i

Vargas Turbo has you covered when you are installing a custom turbo setup. With all of the adapters you need and all the valves necessary, the only real limiting factor is your imagination!

The VTT PCV Flapper delete is used to get rid of the factory flapper, and add a -10 fitting on N54 powered vehicles. This will allow you to run a single or dual external catch can, or your own custom set up.

This fitting is made from 6061-T6 aircraft aluminum anodized black and comes with O-ring, and a stainless steel holding clip.

This part fits the following BMW engines:
2006-2012 N54

The rubber hoses and oil separator can crack or become faulty, leading to vacuum leaks or oil leaks. This is caused by the stress the components are exposed to during heating and cooling cycles, especially if the vehicle is not brought up to operating temperature during driving in cold weather climates.

This kit includes the needed hoses, oil separator, mounting grommet, and hardware.

Fits the following BMWs:
1998-2003 E39 BMW M5

Crankcase Vent Hose ABV0329 is an essential component designed for BMW engines, ensuring optimal performance of the crankcase ventilation system. This high-quality vent hose plays a critical role in regulating and redirecting excess gases from the crankcase back into the engine's intake, reducing harmful emissions and preventing pressure buildup. Crankcase Vent Hose ABV0329 helps maintain engine efficiency and protects against potential damage caused by over-pressurization or oil leaks.

Made from durable, heat-resistant materials, this hose is built to withstand the high temperatures and pressures common in BMW engines. It is a direct-fit replacement, making installation simple and efficient for both professionals and DIY mechanics. Available from Turner Motorsport, Crankcase Vent Hose ABV0329 is the perfect solution for restoring and maintaining your BMW’s crankcase ventilation system.

Key Benefits:

• Ensures proper crankcase ventilation for optimal engine performance
• Reduces harmful emissions by redirecting excess gases into the intake
• Prevents pressure buildup and protects against oil leaks
• Constructed from durable, heat-resistant materials for long-lasting reliability
• Direct-fit replacement, ensuring easy installation for various BMW models
• Available from Turner Motorsport, a trusted source for BMW performance parts

Vargas Turbo has you covered when you are installing a custom turbo setup. With all of the adapters you need and all the valves necessary, the only real limiting factor is your imagination!

This is the adapter fitting that is required to convert your N54 to external PCV if you want to keep your crankcase under vacuum at idle, and anytime you have a vacuum condition in your intake manifold. They are made from 6061-T6 with black anodizing for a long-lasting finish. Includes complete adapter, with all o-rings, and retaining clip.

This must be used in conjunction with  the Vargas billet check valve, and PCV delete fitting or requires plugging of the intake PCV ports. Installs inline on the throttle body, and adds a -8AN male to adapt to a catch cans, or any custom set up.

Made from 6061-T6 with black anodizing for a long-lasting finish. Includes complete adapter, with all o-rings, and retaining clip

This part fits the following BMW engines: 
2006-2012 N54

BMW Oil Separator Valve | E38 E39 540i 740i 740iL M62 4.4L Engine is an essential component designed to maintain optimal engine performance by purging oil vapors from the engine block into the valve cover. This valve features four hoses connecting it to the dipstick, valve cover, and air intake system, ensuring efficient crankcase ventilation. BMW engines, especially in colder climates, are known to experience issues with oil separators freezing if the engine isn't properly warmed up, leading to symptoms such as howling noises followed by oil leaks.

• Effectively purges oil vapors from the engine block to maintain clean operation
• Designed for BMW E38 and E39 models with M62 4.4L engine
• Helps prevent oil separator freezing in cold weather conditions
• Features four hoses connected to the dipstick, valve cover, and air intake for optimal ventilation
• Reduces engine sludge buildup, preventing potential damage and maintaining efficiency
• Durable construction to withstand high temperatures and the demands of the engine

Replace a worn oil separator valve to maintain the proper ventilation and efficiency of your BMW engine, preventing oil leaks and other performance issues.