Vanos System

Genuine BMW E60 M5 E63 M6 Vanos Gearbox Inlet - 11367835343 is a critical component designed to optimize engine performance and reliability in BMW E60 M5 and E63 M6 models. This genuine part ensures precise timing and efficient operation of the VANOS system, maintaining engine efficiency and power output. Crafted to exact OEM specifications, it guarantees perfect fitment and long-lasting durability, making it an essential replacement for maintaining peak engine performance.

• OEM quality ensures perfect fit and function
• Optimizes engine performance and reliability
• Precise timing control for efficient operation
• Ensures consistent power output
• Long-lasting durability for extended service life

Upgrade your BMW E60 M5 or E63 M6 with the Genuine BMW Vanos Gearbox Inlet for enhanced engine performance and reliability.

Genuine BMW Vanos Gearbox, Inlet
This item fits the following BMW Chassis:
E60 M5,E63 M6,E63

Fits BMW Engines including:
S85

VAC's S54 Vanos Hub is designed as a direct replacement for the fragile BMW OE Vanos Hub which typically fails due to a broken drive pin. The VAC Hub has an Upgraded Drive Pin design, which is larger in diameter, as well as more material on the outside wall of the pin. In addition, the hub is made from 4340HT Billet Bar and heat treated to the same BMW OE Rockwell Hardness spec. The upgraded design is not only significantly stronger, but the larger diameter Drive Pins also minimize the huge clearance (approximately 1mm) that was in the original design by BMW and reduces the clearance to 0.2mm. This is critical in helping greatly reduce or eliminate the VANOS noise.

Also, this upgraded design eliminates the need for modifying the Pump Ring or having to buy a replacement, which further saves you money!!!

If you're not sure if your Vanos seals are bad then the only question you need to answer is if you've replaced them. Every unit from the factory came with the same failure prone o-rings and seals, even the re-manufactured units you can still get today. The only real fix is by replacing the seals and o-rings with material that is built to last in the oiled, extreme temperature environment found in these kits. 

A premium product replacement with easy to follow instructions makes rebuilding your Vanos unit a must. Even thought the power loss is barely felt it's the opposite result once you replace the seals, every car that gets rebuilt ends up wowing the customer and all of them saying they didn't realize what they lost. 

There are a number of symptoms that will plague your car as a result of these failing seals such as erratic idle, engine hesitation, stalling, and increased fuel consumption to name a few. If you've been chasing down any of these symptoms with no fix then this could be your issue.

While you 're replacing the seals in your Vanos unit it a good time to install anti-rattle spacers to tighten up the gaps in your stock assembly and get rid of that noisy Vanos clatter.

Rebuild instructions : http://bd8ba3c866c8cbc330ab-7b26c6f3e01bf511d4da3315c66902d6.r6.cf1.rackcdn.com/PDF_12017_BMW_M5X_Dual_Vanos_Rebuild_Kits.pdf

This item fits the following BMWs: 

1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi 
1999-2003 E39 BMW 525i 528i 530i 
2004-2010 E60 BMW 525i 530i 
2004-2006 E83 BMW X3 2.5i X3 3.0i 
2000-2006 E53 BMW X5 3.0i 
1999-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i 
2003-2005 Z4 BMW Z4 2.5i Z4 3.0i 

Take the guesswork out of S54 ownership. This all-inclusive kit targets the two most notorious failure points on the BMW S54 engine: broken exhaust hub tabs and degraded internal seals.

Turner Motorsport S54 VANOS Exhaust Hub Upgrade

The factory S54 exhaust hub is a ticking time bomb. Excessive play between the drive tabs and the oil pump disk creates a rhythmic rattling that eventually shears the tabs off, risking catastrophic engine failure.

While other kits require deep-engine surgery, our Turner Motorsport Hub Upgrade offers a "work smarter" approach.

Precision Engineering: Developed using 3D scanning and CAD modeling for a perfect, interference-free fit.

Superior Materials: Machined from high-strength 4340 steel and hardened to OEM specifications.

No Re-Timing Required: This bolt-on fix eliminates the failure point without the need to disassemble the VANOS unit or disturb engine timing, saving hours of labor.

ECS Tuning VANOS Seal Kit

The original BMW seals are made of Buna-N rubber, which quickly hardens and loses its sealing properties when exposed to synthetic oil and high heat. Our ECS engineering team has corrected this flaw.

Viton™ Upgrade: We utilize high-performance Viton O-rings for the internal seals, seal plate, and solenoid.

Chemical Resistance: These seals are designed to remain pliable and effective for the life of the engine, restoring lost low-end torque and smoothness.

ECS Tuning Rattle Repair Kit

Eliminate the dreaded "marbles in a can" sound. This kit addresses the axial play in the VANOS helical gears.

Hardened Steel: Our rings and washers are precision-ground to resist the wear and deformation that lead to engine rattle.

Silent Operation: Restores the refined sound and feel of your S54 across the entire RPM range.

This solenoid works with the VANOS engine timing system to improve horsepower and torque throughout the RPM range.

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

Genuine BMW Solenoid Valve (Solv) -
This item fits the following BMW Chassis:
E39,E46,E53 X5,E83 X3,E85

Fits BMW Engines including:
M52,M54,M56

If you're not sure if your Vanos seals are bad then the only question you need to answer is if you've replaced them. Every unit from the factory came with the same failure prone o-rings and seals, even the re-manufactured units you can still get today. The only real fix is by replacing the seals and o-rings with material that is built to last in the oiled, extreme temperature environment found in these kits. 

A premium product replacement with easy to follow instructions makes rebuilding your Vanos unit a must. Even thought the power loss is barely felt it's the opposite result once you replace the seals, every car that gets rebuilt ends up wowing the customer and all of them saying they didn't realize what they lost. 

There are a number of symptoms that will plague your car as a result of these failing seals such as erratic idle, engine hesitation, stalling, and increased fuel consumption to name a few. If you've been chasing down any of these symptoms with no fix then this could be your issue.

This kit includes all the right seals and tensioner's for a thorough top end rebuild, this is the best way to rebuild the top half of your engine so you don't have to dig in there again and you can just enjoy the drive.

This item fits the following BMWs: 
1999-2001  E38 BMW  740i 740il 
1999-2003  E39 BMW  540i 
1999-2003  E53 BMW  X5 4.4i X5 4.6i

The BMW M60 and M62 engines found in many 5 series, 7 series, and X5's has two major weak points over time - Vanos seal and timing guides. The timing guides, being the most noticeable and damaging, can be very expensive to have a shop repair when trying to get back on the road. If you have some mechanic abilities and can follow instructions you could get this job done for a lot less, but you'll need the right tools for the job. 

This Schwaben kit features everything you need in one case to perform either job or both making timing service easy and accurate.

Never worry about buying another M60 or M62 timing tool kit again with our LIFETIME REPLACEMENT program - included with your purchase!

Tools included:

• Camshaft locking blocks
• Flywheel locking pin
• Timing chain tension block
• Upper chain tension locks
• Timing wheel alignment tools
• Vanos adjustment socket
• Vanos solenoid socket

Replace your old, leaking VANOS oil pressure feed line to restore proper function and prevent potential failure.

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

Genuine BMW Pressure Hose Assy
This item fits the following BMW Chassis:
E46 M3,E85 Z4M

Fits BMW Engines including:
S54